Abstract: Maize and Indian mustard are significant crops in
semi-arid climate zones of India. Improved water management
requires precise scheduling of irrigation, which in turn requires an
accurate computation of daily crop evapotranspiration (ETc). Daily
crop evapotranspiration comes as a product of reference
evapotranspiration (ET0) and the growth stage specific crop
coefficients modified for daily variation. The first objective of
present study is to develop crop coefficients Kc for Maize and Indian
mustard. The estimated values of Kc for maize at the four crop
growth stages (initial, development, mid-season, and late season) are
0.55, 1.08, 1.25, and 0.75, respectively, and for Indian mustard the Kc
values at the four growth stages are 0.3, 0.6, 1.12, and 0.35,
respectively. The second objective of the study is to compute daily
crop evapotranspiration from ET0 and crop coefficients. Average
daily ETc of maize varied from about 2.5 mm/d in the early growing
period to > 6.5 mm/d at mid season. The peak ETc of maize is 8.3
mm/d and it occurred 64 days after sowing at the reproductive growth
stage when leaf area index was 4.54. In the case of Indian mustard,
average ETc is 1 mm/d at the initial stage, >1.8 mm/d at mid season
and achieves a peak value of 2.12 mm/d on 56 days after sowing.
Improved schedules of irrigation have been simulated based on daily
crop evapo-transpiration and field measured data. Simulation shows a
close match between modeled and field moisture status prevalent
during crop season.
Abstract: This paper proposes the method combining artificial
neural network (ANN) with particle swarm optimization (PSO) to
implement the maximum power point tracking (MPPT) by controlling
the rotor speed of the wind generator. First, the measurements of wind
speed, rotor speed of wind power generator and output power of wind
power generator are applied to train artificial neural network and to
estimate the wind speed. Second, the method mentioned above is
applied to estimate and control the optimal rotor speed of the wind
turbine so as to output the maximum power. Finally, the result reveals
that the control system discussed in this paper extracts the maximum
output power of wind generator within the short duration even in the
conditions of wind speed and load impedance variation.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: We study the performance of compressed beamforming
weights feedback technique in generalized triangular decomposition
(GTD) based MIMO system. GTD is a beamforming technique that
enjoys QoS flexibility. The technique, however, will perform at its
optimum only when the full knowledge of channel state information
(CSI) is available at the transmitter. This would be impossible in
the real system, where there are channel estimation error and limited
feedback. We suggest a way to implement the quantized beamforming
weights feedback, which can significantly reduce the feedback data,
on GTD-based MIMO system and investigate the performance of
the system. Interestingly, we found that compressed beamforming
weights feedback does not degrade the BER performance of the
system at low input power, while the channel estimation error
and quantization do. For comparison, GTD is more sensitive to
compression and quantization, while SVD is more sensitive to the
channel estimation error. We also explore the performance of GTDbased
MU-MIMO system, and find that the BER performance starts
to degrade largely at around -20 dB channel estimation error.
Abstract: The design of an active leg orthosis for tumble
protection is proposed in this paper. The orthosis would be applied to
assist elders or invalids in rebalancing while they fall unexpectedly.
We observe the regain balance motion of healthy and youthful people,
and find the difference to elders or invalids. First, the physical model
of leg would be established, and we consider the leg motions are
achieve through four joints (phalanx stem, ankle, knee, and hip joint)
and five links (phalanges, talus, tibia, femur, and hip bone). To
formulate the dynamic equations, the coordinates which can clearly
describe the position in 3D space are first defined accordance with the
human movement of leg, and the kinematics and dynamics of the leg
movement can be formulated based on the robotics. For the purpose,
assisting elders and invalids in avoiding tumble, the posture variation
of unbalance and regaining balance motion are recorded by the
motion-capture image system, and the trajectory is taken as the desire
one. Then we calculate the force and moment of each joint based on
the leg motion model through programming MATLAB code. The
results would be primary information of the active leg orthosis design
for tumble protection.
Abstract: In the previous multi-solid models,¤ò approach is
used for the calculation of fugacity in the liquid phase. For the first
time, in the proposed multi-solid thermodynamic model,γ approach
has been used for calculation of fugacity in the liquid mixture.
Therefore, some activity coefficient models have been studied that
the results show that the predictive Wilson model is more appropriate
than others. The results demonstrate γ approach using the predictive
Wilson model is in more agreement with experimental data than the
previous multi-solid models. Also, by this method, generates a new
approach for presenting stability analysis in phase equilibrium
calculations. Meanwhile, the run time in γ approach is less than the
previous methods used ¤ò approach. The results of the new model
present 0.75 AAD % (Average Absolute Deviation) from the
experimental data which is less than the results error of the previous
multi-solid models obviously.
Abstract: In this paper, we propose a novel metal oxide
semiconductor field effect transistor with L-shaped channel structure
(LMOS), and several type of L-shaped structures are also designed,
studied and compared with the conventional MOSFET device for the
same average gate length (Lavg). The proposed device electrical
characteristics are analyzed and evaluated by three dimension (3-D)
ISE-TCAD simulator. It can be confirmed that the LMOS devices
have higher on-state drain current and both lower drain-induced
barrier lowering (DIBL) and subthreshold swing (S.S.) than its
conventional counterpart has. In addition, the transconductance and
voltage gain properties of the LMOS are also improved.
Abstract: This paper presents the DC voltage control design of D-STATCOM when the D-STATCOM is used for load voltage regulation. Although, the DC voltage can be controlled by active current of the D-STATCOM, reactive current still affects the DC voltage. To eliminate this effect, the control strategy with elimination effect of the reactive current is proposed and the results of the control with and without the elimination the effect of the reactive current are compared. For obtaining the proportional and integral gains of the PI controllers, the symmetrical optimum and genetic algorithms methods are applied. The stability margin of these methods are obtained and discussed in detail. In addition, the performance of the DC voltage control based on symmetrical optimum and genetic algorithms methods are compared. Effectiveness of the controllers designed was verified through computer simulation performed by using Power System Tool Block (PSB) in SIMULINK/MATLAB. The simulation results demonstrated that the DC voltage control proposed is effective in regulating DC voltage when the DSTATCOM is used for load voltage regulation.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: This paper discusses the performance modeling and availability analysis of Yarn Dyeing System of a Textile Industry. The Textile Industry is a complex and repairable engineering system. Yarn Dyeing System of Textile Industry consists of five subsystems arranged in series configuration. For performance modeling and analysis of availability, a performance evaluating model has been developed with the help of mathematical formulation based on Markov-Birth-Death Process. The differential equations have been developed on the basis of Probabilistic Approach using a Transition Diagram. These equations have further been solved using normalizing condition in order to develop the steady state availability, a performance measure of the system concerned. The system performance has been further analyzed with the help of decision matrices. These matrices provide various availability levels for different combinations of failure and repair rates for various subsystems. The findings of this paper are therefore, considered to be useful for the analysis of availability and determination of the best possible maintenance strategies which can be implemented in future to enhance the system performance.
Abstract: The purpose of this study is to understand how
consumers react to a company's promotional offers with mobile
applications (APP) as premiums. This paper presents the results of an
experimental study where five features of APP were involved: the
cost (free/discounted) for earning APP, the relationship between APP
and the promoted product, the perceived usefulness, the perceived
ease of use, and the perceived playfulness of APP in the context of
light foods purchase. The results support that the above features,
except perceived ease of use, have substantial influences on
consumers' intention to adopt the APP. Among the five features, the
cost for earning APP has the most impact on the adopting intention
of APP. The study also found a positive influence of adopting
intention of APP on the consumer's purchase intention of the
promoted product. Thus, APP-based premiums may enhance the
consumer's purchase intention of a company's promoted products.
Abstract: This paper proposes a novel game theoretical
technique to address the problem of data object replication in largescale
distributed computing systems. The proposed technique draws
inspiration from computational economic theory and employs the
extended Vickrey auction. Specifically, players in a non-cooperative
environment compete for server-side scarce memory space to
replicate data objects so as to minimize the total network object
transfer cost, while maintaining object concurrency. Optimization of
such a cost in turn leads to load balancing, fault-tolerance and
reduced user access time. The method is experimentally evaluated
against four well-known techniques from the literature: branch and
bound, greedy, bin-packing and genetic algorithms. The experimental
results reveal that the proposed approach outperforms the four
techniques in both the execution time and solution quality.
Abstract: In this paper, a new encoding algorithm of spectral envelope based on NLMS in G.729.1 for VoIP is proposed. In the TDAC part of G.729.1, the spectral envelope and MDCT coefficients extracted in the weighted CELP coding error (lower-band) and the higher-band input signal are encoded. In order to reduce allocation bits for spectral envelope coding, a new quantization algorithm based on NLMS is proposed. Also, reduced bits are used to enhance sound quality. The performance of the proposed algorithm is evaluated by sound quality and bit reduction rates in clean and frame loss conditions.
Abstract: This paper analyzes the patterns of the Monte Carlo
data for a large number of variables and minterms, in order to
characterize the circuit path length behavior. We propose models
that are determined by training process of shortest path length
derived from a wide range of binary decision diagram (BDD)
simulations. The creation of the model was done use of feed forward
neural network (NN) modeling methodology. Experimental results
for ISCAS benchmark circuits show an RMS error of 0.102 for the
shortest path length complexity estimation predicted by the NN
model (NNM). Use of such a model can help reduce the time
complexity of very large scale integrated (VLSI) circuitries and
related computer-aided design (CAD) tools that use BDDs.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: This study presents a blower for air management system of fuel cell modules. A blower is composed of BLDC motor and impeller. Magnetic equivalent circuit model and finite element analysis are used to design the motor, and an improved structure is considered to reduce a mechanical loss induced from bearing units. Finally, air blower system combined with the motor and an impeller is manufactured and output properties, such as an air pressure and an amount of flowing air, are measured. Through the experimental results, a validity of the simulated one is confirmed.
Abstract: Wireless sensor network is formed with the combination of sensor nodes and sink nodes. Recently Wireless sensor network has attracted attention of the research community. The main application of wireless sensor network is security from different attacks both for mass public and military. However securing these networks, by itself is a critical issue due to many constraints like limited energy, computational power and lower memory. Researchers working in this area have proposed a number of security techniques for this purpose. Still, more work needs to be done.In this paper we provide a detailed discussion on security in wireless sensor networks. This paper will help to identify different obstacles and requirements for security of wireless sensor networks as well as highlight weaknesses of existing techniques.
Abstract: In the present study, the response of Nili Ravi buffalo
oocytes to recombinant human follicle stimulating hormone (rhFSH)
(Organon) on meiotic maturation in vitro was examined. Oocytes
were matured in vitro in medium containing either 0 or 0.05 IU/ ml
rhFSH and the stage of nuclear maturation recorded after 24 hours.
The percentage of oocytes in the control group undergoing germinal
vesicle breakdown (GVBD) observed after 24 hours of culture was
29 % whereas as in rhFSH group the percentage was 10 % were at
this stage (P< 0.001).Thus in the presence of rhFSH, a significantly
greater number of oocytes had progressed to the more advanced
stages of nuclear maturation. Indeed, the maturation of GV
(Germinal Vesicle) stage oocytes to the metaphase II (M II) stage
after 24 hours was significantly (P< 0.0001) increased by the
addition of rhFSH (82 % VS 47 %). The percentage of degenerated
oocytes after 24 hours of culture was 24 % in control group, whereas
in rhFSH group the percentage was 8 % after 24 hours. Degeneration
of the oocytes after 24 hours was not significantly (P = 0. 9361)
decreased.
Abstract: In this paper some results on strict stability heve beeb extended for fuzzy differential equations with impulse effect using Lyapunov functions and Razumikhin technique.
Abstract: In many cases, there are some time lag between the consumption of inputs and the production of outputs. This time lag effect should be considered in evaluating the performance of organizations. Recently, a couple of DEA models were developed for considering time lag effect in efficiency evaluation of research activities. Multi-periods input(MpI) and Multi-periods output(MpO) models are integrate models to calculate simple efficiency considering time lag effect. However, these models can’t discriminate efficient DMUs because of the nature of basic DEA model in which efficiency scores are limited to ‘1’. That is, efficient DMUs can’t be discriminated because their efficiency scores are same. Thus, this paper suggests a super-efficiency model for efficiency evaluation under the consideration of time lag effect based on the MpO model. A case example using a long term research project is given to compare the suggested model with the MpO model.