Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: In this paper a technique for increasing the
convergence rate of fractionally spaced channel equalizer is
proposed. Instead of symbol-spaced updating of the equalizer filter, a
mechanism has been devised to update the filter at a higher rate. This
ensures convergence of the equalizer filter at a higher rate and
therefore less time-consuming. The proposed technique has been
simulated and tested for two-ray modeled channels with various
delay spreads. These channels include minimum-phase and nonminimum-
phase channels. Simulation results suggest that that
proposed technique outperforms the conventional technique of
symbol-spaced updating of equalizer filter.
Abstract: In wireless sensor networks,the mobile agent technology is used in data fusion. According to the node residual energy and the results of partial integration,we design the node clustering algorithm. Optimization of mobile agent in the routing within the cluster strategy for wireless sensor networks to further reduce the amount of data transfer. Through the experiments, using mobile agents in the integration process within the cluster can be reduced the path loss in some extent.
Abstract: A new approach for facial expressions recognition based on face context and adaptively weighted sub-pattern PCA (Aw-SpPCA) has been presented in this paper. The facial region and others part of the body have been segmented from the complex environment based on skin color model. An algorithm has been proposed to accurate detection of face region from the segmented image based on constant ratio of height and width of face (δ= 1.618). The paper also discusses on new concept to detect the eye and mouth position. The desired part of the face has been cropped to analysis the expression of a person. Unlike PCA based on a whole image pattern, Aw-SpPCA operates directly on its sub patterns partitioned from an original whole pattern and separately extracts features from them. Aw-SpPCA can adaptively compute the contributions of each part and a classification task in order to enhance the robustness to both expression and illumination variations. Experiments on single standard face with five types of facial expression database shows that the proposed method is competitive.
Abstract: Antimosy-doped tin oxide (ATO) particles were
prepared via chemical coprecipitation and reverse emulsion. The size
and size distribution of ATO particles were obviously decreased via
reverse microemulsion method. At the relatively high yield the ATO
particles were nearly spherical in shape, meanwhile the crystalline
structure and excellent conductivity were reserved, which could satisfy
the requirement as composite fillers, such as dielectric filler of
polyimide film.
Abstract: This work explores blind image deconvolution by recursive function approximation based on supervised learning of neural networks, under the assumption that a degraded image is linear convolution of an original source image through a linear shift-invariant (LSI) blurring matrix. Supervised learning of neural networks of radial basis functions (RBF) is employed to construct an embedded recursive function within a blurring image, try to extract non-deterministic component of an original source image, and use them to estimate hyper parameters of a linear image degradation model. Based on the estimated blurring matrix, reconstruction of an original source image from a blurred image is further resolved by an annealed Hopfield neural network. By numerical simulations, the proposed novel method is shown effective for faithful estimation of an unknown blurring matrix and restoration of an original source image.
Abstract: Mechanical interaction between endothelial cells (ECs) and the extracellular matrix (or collagen gel) is known to influence the sprouting response of endothelial cells during angiogenesis. This influence is believed to impact on the capability of endothelial cells to sense soluble chemical cues. Quantitative analysis of endothelial-cell-mediated displacement of the collagen gel provides a means to explore this mechanical interaction. Existing analysis in this context is generally limited to 2D settings. In this paper, we investigate the mechanical interaction between endothelial cells and the extracellular matrix in terms of the endothelial-cellmediated displacement of the collagen gel in both 2D and 3D. Digital image correlation and Digital volume correlation are applied on confocal reflectance image stacks to analyze cell-mediated displacement of the gel. The skeleton of the sprout is extracted from phase contrast images and superimposed on the displacement field to further investigate the link between the development of the sprout and the displacement of the gel.
Abstract: The development of Internet technology in recent years has led to a more active role of users in creating Web content. This has significant effects both on individual learning and collaborative knowledge building. This paper will present an integrative framework model to describe and explain learning and knowledge building with shared digital artifacts on the basis of Luhmann-s systems theory and Piaget-s model of equilibration. In this model, knowledge progress is based on cognitive conflicts resulting from incongruities between an individual-s prior knowledge and the information which is contained in a digital artifact. Empirical support for the model will be provided by 1) applying it descriptively to texts from Wikipedia, 2) examining knowledge-building processes using a social network analysis, and 3) presenting a survey of a series of experimental laboratory studies.
Abstract: In the urban traffic network, the intersections are the
“bottleneck point" of road network capacity. And the arterials are the
main body in road network and the key factor which guarantees the
normal operation of the city-s social and economic activities. The
rapid increase in vehicles leads to seriously traffic jam and cause the
increment of vehicles- delay. Most cities of our country are
traditional single control system, which cannot meet the need for the
city traffic any longer. In this paper, Synchro6.0 as a platform to
minimize the intersection delay, optimizesingle signal cycle and split
for Zhonghua Street in Handan City. Meanwhile, linear control
system uses to optimize the phase for the t arterial road in this
system. Comparing before and after use the control, capacities and
service levels of this road and the adjacent road have improved
significantly.
Abstract: In this paper we considered the Neumann problem for
the fourth order differential equation. First we define the weighted Sobolev space
2 Wα and generalized solution for this equation. Then we consider the existence and uniqueness of the generalized solution,
as well as give the description of the spectrum and of the domain of definition of the corresponding operator.
Abstract: Higher-order Statistics (HOS), also known as
cumulants, cross moments and their frequency domain counterparts,
known as poly spectra have emerged as a powerful signal processing
tool for the synthesis and analysis of signals and systems. Algorithms
used for the computation of cross moments are computationally
intensive and require high computational speed for real-time
applications. For efficiency and high speed, it is often advantageous
to realize computation intensive algorithms in hardware. A promising
solution that combines high flexibility together with the speed of a
traditional hardware is Field Programmable Gate Array (FPGA). In
this paper, we present FPGA-based parallel architecture for the
computation of third-order cross moments. The proposed design is
coded in Very High Speed Integrated Circuit (VHSIC) Hardware
Description Language (VHDL) and functionally verified by
implementing it on Xilinx Spartan-3 XC3S2000FG900-4 FPGA.
Implementation results are presented and it shows that the proposed
design can operate at a maximum frequency of 86.618 MHz.
Abstract: Efficient preprocessing is very essential for automatic
recognition of handwritten documents. In this paper, techniques on
segmenting words in handwritten Arabic text are presented. Firstly,
connected components (ccs) are extracted, and distances among
different components are analyzed. The statistical distribution of this
distance is then obtained to determine an optimal threshold for words
segmentation. Meanwhile, an improved projection based method is
also employed for baseline detection. The proposed method has been
successfully tested on IFN/ENIT database consisting of 26459
Arabic words handwritten by 411 different writers, and the results
were promising and very encouraging in more accurate detection of
the baseline and segmentation of words for further recognition.
Abstract: As an economic and safe structure, Bi-steel is widely
used in reinforced concrete with less consumption of steel. In this
paper, III Bi-steel concrete beam has been analyzed. Through careful
observation and theoretical analysis, the new calculating formulae for
structural rigidity and crack have been formulated for this Bi-steel
concrete beam. And structural rigidity and the crack features have also
been theoretically analyzed.
Abstract: Wastages such as grated coconut meat, spent tea and used sugarcane had contributed negative impacts to the environment. Vermicomposting method is fully utilized to manage the wastes towards a more sustainable approach. The worms that are used in the vermicomposting are Eisenia foetida and Eudrillus euginae. This research shows that the vermicompost of wastages has voltage of electrical energy and is able to light up the Light-Emitting Diode (LED) device. Based on the experiment, the use of replicated and double compartments of the component will produce double of voltage. Hence, for conclusion, this harmless and low cost technology of vermicompost can act as a dry cell in order to reduce the usage of hazardous chemicals that can contaminate the environment.
Abstract: A numerical method for Riccati equation is presented in this work. The method is based on the replacement of unknown functions through a truncated series of hybrid of block-pulse functions and Chebyshev polynomials. The operational matrices of derivative and product of hybrid functions are presented. These matrices together with the tau method are then utilized to transform the differential equation into a system of algebraic equations. Corresponding numerical examples are presented to demonstrate the accuracy of the proposed method.
Abstract: Cross sections of As radionuclides in the interaction of natGe with 14-30 MeV protons have been deduced by off-line y-ray spectroscopy to find optimal reaction channels leading to radiotracers for positron emission tomography. The experimental results were compared with the previous results and those estimated by the compound nucleus reaction model.
Abstract: In 2002 an amendment to SOLAS opened for
lightweight material constructions in vessels if the same fire safety as
in steel constructions could be obtained. FISPAT (FIreSPread
Analysis Tool) is a computer application that simulates fire spread
and fault injection in cruise vessels and identifies fire sensitive areas.
It was developed to analyze cruise vessel designs and provides a
method to evaluate network layout and safety of cruise vessels. It
allows fast, reliable and deterministic exhaustive simulations and
presents the result in a graphical vessel model. By performing the
analysis iteratively while altering the cruise vessel design it can be
used along with fire chamber experiments to show that the
lightweight design can be as safe as a steel construction and that
SOLAS regulations are fulfilled.
Abstract: This paper presents a method to support dynamic
packing in cases when no collision-free path can be found. The
method, which is primarily based on path planning and shrinking of
geometries, suggests a minimal geometry design change that results
in a collision-free assembly path. A supplementing approach to
optimize geometry design change with respect to redesign cost is
described. Supporting this dynamic packing method, a new method
to shrink geometry based on vertex translation, interweaved with
retriangulation, is suggested. The shrinking method requires neither
tetrahedralization nor calculation of medial axis and it preserves the
topology of the geometry, i.e. holes are neither lost nor introduced.
The proposed methods are successfully applied on industrial
geometries.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.