Abstract: This study aimed to investigate the magnetic resonance
(MR) signal enhancement ratio (ER) of contrast-enhanced MR
angiography (CE-MRA) in normal rats with gadobenate dimeglumine
(Gd-BOPTA) using a clinical 3T scanner and an extremity coil. The
relaxivities of Gd-BOPTA with saline only and with 4.5% human
serum albumin (HSA) were also measured. Compared with
Gadolinium diethylenetriaminepentaacetic acid (Gd-DTPA),
Gd-BOPTA had higher relaxivities. The maximum ER of aorta (ERa),
kidney, liver and muscle with Gd-BOPTA were higher than those with
Gd-DTPA. The maximum ERa appeared at 1.2 min and decayed to half
at 10 min after Gd-BOPTA injection. This information is helpful for
the design of CE-MRA study of rats.
Abstract: This work is undertaken to develop a methodology to enhance the management of dredged marine and river sediments in the North of France. The main objective of this study is to determine the main characteristics of these sediments. In this order, physical, mineralogical and chemical properties of both types of sediments are measured. Moreover, their potential impacts on the environment are assessed throughout leaching tests. From the obtained results, the potential of their use in road engineering is discussed.
Abstract: Bir El Djir is an important coastal township in Oran
department, located at 450 Km far away from Algiers on northwest of
Algeria. In this coastal area, the urban sprawl is one of the main
problems that reduce the limited highly fertile land. So, using the
remote sensing and GIS technologies have shown their great
capabilities to solve many earth resources issues.
The aim of this study is to produce land use and cover map for the
studied area at varied periods to monitor possible changes that may
occurred, particularly in the urban areas and subsequently predict
likely changes. For this, two spatial images SPOT and Landsat
satellites from 1987 and 2014 respectively were used to assess the
changes of urban expansion and encroachment during this period
with photo-interpretation and GIS approach.
The results revealed that the town of Bir El Djir has shown a
highest growth rate in the period 1987-2014 which is 1201.5 hectares
in terms of area. These expansions largely concern the new real estate
constructions falling within the social and promotional housing
programs launched by the government.
The most urban expansion is characterized by the new
construction in the form of spontaneous or peripheral precarious
habitat, but also unstructured slums settled especially in the
southeastern part of town.
Abstract: Reverse Logistics (RL) Network is considered as
complex and dynamic network that involves many stakeholders such
as: suppliers, manufactures, warehouse, retails and costumers, this
complexity is inherent in such process due to lack of perfect
knowledge or conflicting information. Ontologies on the other hand
can be considered as an approach to overcome the problem of sharing
knowledge and communication among the various reverse logistics
partners. In this paper we propose a semantic representation based on
hybrid architecture for building the Ontologies in ascendant way, this
method facilitates the semantic reconciliation between the
heterogeneous information systems that support reverse logistics
processes and product data.
Abstract: The ad hoc networks are the future of wireless
technology as everyone wants fast and accurate error free information
so keeping this in mind Bit Error Rate (BER) and power is optimized
in this research paper by using the Genetic Algorithm (GA). The
digital modulation techniques used for this paper are Binary Phase
Shift Keying (BPSK), M-ary Phase Shift Keying (M-ary PSK), and
Quadrature Amplitude Modulation (QAM). This work is
implemented on Wireless Ad Hoc Networks (WLAN). Then it is
analyze which modulation technique is performing well to optimize
the BER and power of WLAN.
Abstract: In this paper, fractional order feedback control of a ball
beam model is investigated. The ball beam model is a particular
example of the double Integrator system having strongly nonlinear
characteristics and unstable dynamics which make the control of
such system a challenging task. Most of the work in fractional order
control systems are in theoretical nature and controller design and its
implementation in practice is very small. In this work, a successful
attempt has been made to design a fractional order PIλDμcontroller
for a benchmark laboratory ball and beam model. Better performance
can be achieved using a fractional order PID controller and it is
demonstrated through simulations results with a comparison to the
classic PID controller.
Abstract: This study presents the optimal design and formulation of a kinematic model of a flexible slider crank mechanism. The objective of the proposed innovative design is to take extra advantage of the compliant mechanism and maximize the fatigue life by applying the Taguchi method. A formulated kinematic model is developed using a pseudo-rigid-body model (PRBM). By means of mathematic models, the kinematic behaviors of the flexible slider crank mechanism are captured using MATLAB software. Finite element analysis (FEA) is used to show the stress distribution. The results show that the optimal shape of the flexible hinge includes a force of 8.5N, a width of 9mm and a thickness of 1.1mm. Analysis of variance shows that the thickness of the proposed hinge is the most significant parameter, with an F test of 15.5. Finally, a prototype is manufactured to prepare for testing the kinematic and dynamic behaviors.
Abstract: Fishes, in general, follow ammonotelic mode of excretion. However, certain stress factors may provoke them to excrete urea. In the present study, the possible role of ureogenesis to avoid accumulation of toxic ammonia under water-restricted condition was tested in Heteropneustes fossilis. A total of hundred fishes were collected and sacrificed. Excretory urea and ammonia were estimated in the water of the aquarium and glutamate dehydrogenase acitivity was measured in the hepatic tissue. During the experimental period, excretory ammonia in Heteropneustes fossilis was found between 931% to 16% above the baseline ammonia and excretory urea was found between 112% to 898% above the baseline urea. A high degree of correlation with r (coefficient of correlation) above 0.9 is observed between excretory ammonia and urea in Heteropneustes fossilis. However, only a moderate degree of correlation is observed between the activity of glutamate dehydrogenase and excretory ammonia and urea.
Abstract: Extreme rainfall frequency analysis for Meteorological Sub-Division 4 of India was analyzed using L-moments approach. Serial Correlation and Mann Kendall tests were conducted for checking serially independent and stationarity of the observations. The discordancy measure for the sites was conducted to detect the discordant sites. The regional homogeneity was tested by comparing with 500 generated homogeneous regions using a 4 parameter Kappa distribution. The best fit distribution was selected based on ZDIST statistics and L-moments ratio diagram from the five extreme value distributions GPD, GLO, GEV, P3 and LP3. The LN3 distribution was selected and regional rainfall frequency relationship was established using index-rainfall procedure. A regional mean rainfall relationship was developed using multiple linear regression with latitude and longitude of the sites as variables.
Abstract: Stirred tanks are widely used in all industrial sectors. The need for further studies of the mixing operation and its different aspects comes from the diversity of agitation tools and implemented geometries in addition to the specific characteristics of each application. Viscous fluids are often encountered in industry and they represent the majority of treated cases, as in the polymer sector, food processing, pharmaceuticals and cosmetics. That's why in this paper, we will present a three-dimensional numerical study using the software Fluent, to study the effect of varying the fluid viscosity in a stirred tank with a Rushton turbine. This viscosity variation was performed by adding carboxymethylcellulose (CMC) to the fluid (water) in the vessel. In this work, we studied first the flow generated in the tank with a Rushton turbine. Second, we studied the effect of the fluid viscosity variation on the thermodynamic quantities defining the flow. For this, three viscosities (0.9% CMC, 1.1% CMC and 1.7% CMC) were considered.
Abstract: In this investigation variation of cyclic loading effect on fatigue crack growth is the studied. This study is performed on 2024 T351 and 7050-T74 aluminum alloys, used in aeronautical structures. The propagation model used in this study is NASGRO model. In constant amplitude loading (CA), effect of stress ratio has been investigated. Fatigue life and fatigue crack growth rate were affected by this factor. Results showed an increasing in fatigue crack growth rates (FCGRs) with increasing stress ratio. Variable amplitude loading (VAL) can take many forms i.e. with a single overload, overload band… etc. The shape of these loads affects strongly the fracture life and FCGRs. The application of a single overload (ORL) decrease the FCGR and increase the delay crack length caused by the formation of a larger plastic zone compared to the plastic zone due without VAL. The fatigue behavior of the both material under single overload has been compared.
Abstract: In this investigation an empirical study was made on fatigue crack initiation on 7075 T6 and 7075 T71 Al-alloys under constant amplitude loading. In initiation stage, local strain approach at the notch was applied. Single Edge Notch Tensile specimen with semi circular notch is used. Based on experimental results, effect of mean stress, is highlights on fatigue initiation life. Results show that fatigue life initiation is affected by notch geometry and mean stress.
Abstract: The tribological outcomes of micro dent are found to be outstanding in many engineering and natural surfaces. Ceramic (Al2O3) is considered one of the most potential material to bearing surfaces particularly, artificial hip or knee implant. A well-defined micro dent on alumina oxide interface could further decrease friction and wear rate, thus increase their stability and durability. In this study we fabricated circular micro dent surface profiles (Dia: 400µm, Depth 20µm, P: 1.5mm; Dia: 400µm, Depth 20µm, P: 2mm) on pure Al2O3 (99.6%) substrate by using a micro tool machines. A preliminary tribological experiment was carried out to compare friction coefficient of these fabricated dent surfaces with that of non-textured surfaces. The experiment was carried on well know pin-on-disk specimens while other experimental parameters such as hertz pressure, speed, lubrication, and temperature were maintained to standard of simulated hip joints condition. The experiment results revealed that micro dent surface texture reduced 15%, 8% and 4% friction coefficient under 0.132,0.162, 0.187 GPa contact pressure respectively. Since this is a preliminary tribological study, we will pursue further experiments considering higher ranges of dent profiles and longer run experiments. However, the preliminary results confirmed the suitability of fabricating dent profile to ceramic surfaces by using micro tooling, and also their improved tribological performance in simulated hip joints.
Abstract: Integrins are a large family of multidomain α/β cell
signaling receptors. Some integrins contain an additional inserted I
domain, whose earliest expression appears to be with the chordates,
since they are observed in the urochordates Ciona intestinalis (vase
tunicate) and Halocynthia roretzi (sea pineapple), but not in integrins
of earlier diverging species. The domain-s presence is viewed as a
hallmark of integrins of higher metazoans, however in vertebrates,
there are clearly three structurally-different classes: integrins without
I domains, and two groups of integrins with I domains but separable
by the presence or absence of an additional αC helix. For example,
the αI domains in collagen-binding integrins from Osteichthyes
(bony fish) and all higher vertebrates contain the specific αC helix,
whereas the αI domains in non-collagen binding integrins from
vertebrates and the αI domains from earlier diverging urochordate
integrins, i.e. tunicates, do not. Unfortunately, within the early
chordates, there is an evolutionary gap due to extinctions between the
tunicates and cartilaginous fish. This, coupled with a knowledge gap
due to the lack of complete genomic data from surviving species,
means that the origin of collagen-binding αC-containing αI domains
remains unknown. Here, we analyzed two available genomes from
Callorhinchus milii (ghost shark/elephant shark; Chondrichthyes –
cartilaginous fish) and Petromyzon marinus (sea lamprey;
Agnathostomata), and several available Expression Sequence Tags
from two Chondrichthyes species: Raja erinacea (little skate) and
Squalus acanthias (dogfish shark); and Eptatretus burgeri (inshore
hagfish; Agnathostomata), which evolutionary reside between the
urochordates and osteichthyes. In P. marinus, we observed several
fragments coding for the αC-containing αI domain, allowing us to
shed more light on the evolution of the collagen-binding integrins.
Abstract: Diesel Engines emit complex mixtures of inorganic
and organic compounds in the form of both solid and vapour phase
particles. Most of the particulates released are ultrafine nanoparticles
which are detrimental to human health and can easily enter the body
by respiration. The emissions standards on particulate matter release
from diesel engines are constantly upgraded within the European
Union and with future regulations based on the particles numbers
released instead of merely mass, the need for effective aftertreatment
devices will increase. Standard particulate filters in the form of wall
flow filters can have problems with high soot accumulation,
producing a large exhaust backpressure. A potential solution would
be to combine the standard filter with a flow through filter to reduce
the load on the wall flow filter. In this paper soot particle trapping has
been simulated in different continuous flow filters of monolithic
structure including the use of promoters, at laminar flow conditions.
An Euler Lagrange model, the discrete phase model in Ansys used
with user defined functions for forces acting on particles. A method
to quickly screen trapping of 5 nm and 10 nm particles in different
catalysts designs with tracers was also developed.
Simulations of square duct monoliths with promoters show that the
strength of the vortices produced are not enough to give a high
amount of particle deposition on the catalyst walls. The smallest
particles in the simulations, 5 and 10 nm particles were trapped to a
higher extent, than larger particles up to 1000 nm, in all studied
geometries with the predominant deposition mechanism being
Brownian diffusion. The comparison of the different filters designed
with a wall flow filter does show that the options for altering a design
of a flow through filter, without imposing a too large pressure drop
penalty are good.
Abstract: An experiment was performed in the south of
Morocco in order to evaluate the effect of deficit irrigation by treated
wastewater on chickpea production. We applied six irrigation
treatments on a local variety of chickpea by supplying alternatively
50 or 100% of ETm in a completely randomized design.
We found a highly significant difference between treatments in
terms of biomass production. Drought stress during the vegetative
period showed highest yield with 6.5 t/ha which was more than the
yield obtained for the control (4.9 t/ha). The optimal crop stage in
which deficit irrigation can be applied is the vegetative growth stage,
as the crop has a chance to develop its root system, to be able to
cover the plant needs for water and nutrient supply during the rest of
cycle, and non stress conditions during the flowering and seed filling
stages allow the plant to optimize its photosynthesis and carbon
translocation, therefore increase its productivity.
Abstract: At present, dictionary attack has been the basic tool for
recovering key passwords. In order to avoid dictionary attack, users
purposely choose another character strings as passwords. According to
statistics, about 14% of users choose keys on a keyboard (Kkey, for
short) as passwords. This paper develops a framework system to attack
the password chosen from Kkeys and analyzes its efficiency. Within
this system, we build up keyboard rules using the adjacent and parallel
relationship among Kkeys and then use these Kkey rules to generate
password databases by depth-first search method. According to the
experiment results, we find the key space of databases derived from
these Kkey rules that could be far smaller than the password databases
generated within brute-force attack, thus effectively narrowing down
the scope of attack research. Taking one general Kkey rule, the
combinations in all printable characters (94 types) with Kkey adjacent
and parallel relationship, as an example, the derived key space is about
240 smaller than those in brute-force attack. In addition, we
demonstrate the method's practicality and value by successfully
cracking the access password to UNIX and PC using the password
databases created
Abstract: This study is concerned with pH solution detection
using 2 × 4 flexible sensor array based on a plastic polyethylene
terephthalate (PET) substrate that is coated a conductive layer and a
ruthenium dioxide (RuO2) sensitive membrane with the technologies
of screen-printing and RF sputtering. For data analysis, we also
prepared a dynamic measurement system for acquiring the response
voltage and analyzing the characteristics of the working electrodes
(WEs), such as sensitivity and linearity. In this condition, an array
measurement system was designed to acquire the original signal from
sensor array, and it is based on the method of digital signal processing
(DSP). The DSP modifies the unstable acquisition data to a direct
current (DC) output using the technique of digital filter. Hence, this
sensor array can obtain a satisfactory yield, 62.5%, through the design
measurement and analysis system in our laboratory.
Abstract: The hard clam (meretrix lusoria) cultivated industry
has been developed vigorously for recent years in Taiwan, and
seawater quality determines the cultivated environment. The pH
concentration variation affects survival rate of meretrix lusoria
immediately. In order to monitor seawater quality, solid-state sensing
electrode of ruthenium-doped titanium dioxide (TiO2:Ru) is developed
to measure hydrogen ion concentration in different cultivated
solutions. Because the TiO2:Ru sensing electrode has high chemical
stability and superior sensing characteristics, thus it is applied as a pH
sensor. Response voltages of TiO2:Ru sensing electrode are readout by
instrument amplifier in different sample solutions. Mean sensitivity
and linearity of TiO2:Ru sensing electrode are 55.20 mV/pH and 0.999
from pH1 to pH13, respectively. We expect that the TiO2:Ru sensing
electrode can be applied to real environment measurement, therefore
we collect two sample solutions by different meretrix lusoria
cultivated ponds in the Yunlin, Taiwan. The two sample solutions are
both measured for 200 seconds after calibration of standard pH buffer
solutions (pH7, pH8 and pH 9). Mean response voltages of sample 1
and sample 2 are -178.758 mV (Standard deviation=0.427 mV) and
-180.206 mV (Standard deviation =0.399 mV), respectively. Response
voltages of the two sample solutions are between pH 8 and pH 9 which
conform to weak alkali range and suitable meretrix lusoria growth. For
long-term monitoring, drift of cultivated solutions (sample 1 and
sample 2) are 1.16 mV/hour and 1.03 mV/hour, respectively.
Abstract: Business Process Management (BPM) helps in optimizing the business processes inside an enterprise. But BPM architecture does not provide any help for extending the enterprise. Modern business environments and rapidly changing technologies are asking for brisk changes in the business processes. Service Oriented Architecture (SOA) can help in enabling the success of enterprise-wide BPM. SOA supports agility in software development that is directly related to achieve loose coupling of interacting software agents. Agility is a premium concern of the current software designing architectures. Together, BPM and SOA provide a perfect combination for enterprise computing. SOA provides the capabilities for services to be combined together and to support and create an agile, flexible enterprise. But there are still many questions to answer; BPM is better or SOA? and what is the future track of BPM and SOA? This paper tries to answer some of these important questions.