Abstract: Wireless Sensor Network (WSN) comprises of sensor
nodes which are designed to sense the environment, transmit sensed
data back to the base station via multi-hop routing to reconstruct
physical phenomena. Since physical phenomena exists significant
overlaps between temporal redundancy and spatial redundancy, it is
necessary to use Redundancy Suppression Algorithms (RSA) for sensor
node to lower energy consumption by reducing the transmission
of redundancy. A conventional algorithm of RSAs is threshold-based
RSA, which sets threshold to suppress redundant data. Although
many temporal and spatial RSAs are proposed, temporal-spatial RSA
are seldom to be proposed because it is difficult to determine when
to utilize temporal or spatial RSAs. In this paper, we proposed a
novel temporal-spatial redundancy suppression algorithm, Codebookbase
Redundancy Suppression Mechanism (CRSM). CRSM adopts
vector quantization to generate a codebook, which is easily used to
implement temporal-spatial RSA. CRSM not only achieves power
saving and reliability for WSN, but also provides the predictability
of network lifetime. Simulation result shows that the network lifetime
of CRSM outperforms at least 23% of that of other RSAs.
Abstract: In this study, a three-dimensional haptotaxis model to simulate the migration of a population of cancer cells has been proposed. The invasion of cancer cells is related with the hapto-attractant and the effect of the interface energies between the cells and the ECM. The diffuse interface model, which incorporates the haptotaxis mechanism and interface energies, is employed. The semi-implicit Fourier spectral scheme is adopted for efficient evaluation of the simulation. The simulation results thoroughly reveal the dynamics of cancer-cell migration.
Abstract: In this paper fatigue crack initiation and propagation in notched plate under constant amplitude loading through tensile residual stress field of 2024 T351 Al-alloy plate were investigated. Residual stress field was generated by plastic deformation using finite element method (FEM) where isotropic hardening in Von Mises model was applied. Simulation of fatigue behavior was made on AFGROW code. It was shown that the fatigue crack initiation and propagation were affected by level of residual stress filed. In this investigation, the presence of tensile residual stresses at notch (hole) reduces considerably the total fatigue life. It was shown that the decreasing in stress reduces the fatigue crack growth rates.
Abstract: The study attempted to identify the dominant
intelligences of athletes by comparing the developmental differences
of multiple intelligences between athletes and non-athletes. The
weekly specialized training hours and years of specialized training
was examined to see how it can predict the dominant intelligence with
the age factor controlled. There were 355 participants in the research
(202 athletes and 153 non-athletes). Collected data were analyzed with
one-way MANOVA and multiple hierarchical regression. The results
suggested the dominant intelligences of athletes were Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence. The weekly specialized training hours and years of
specialized training could effectively predict the Interpersonal
Intelligence, Bodily-Kinesthetic Intelligence, and Intrapersonal
Intelligence of athletes. The author suggested the future studies could
focus on the theory construction of weekly specialized training and
years of specialized training. Also, the studies on using “Bridge
strategy" by the athletes to guide disadvantage intelligences with
dominant intelligences are highly valued.
Abstract: In this paper we present an off line system for the
recognition of the handwritten numeric chains. Our work is divided
in two big parts. The first part is the realization of a recognition
system of the isolated handwritten digits. In this case the study is
based mainly on the evaluation of neural network performances,
trained with the gradient back propagation algorithm. The used
parameters to form the input vector of the neural network are
extracted on the binary images of the digits by several methods: the
distribution sequence, the Barr features and the centred moments of
the different projections and profiles. The second part is the
extension of our system for the reading of the handwritten numeric
chains constituted of a variable number of digits. The vertical
projection is used to segment the numeric chain at isolated digits and
every digit (or segment) will be presented separately to the entry of
the system achieved in the first part (recognition system of the
isolated handwritten digits). The result of the recognition of the
numeric chain will be displayed at the exit of the global system.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.
Abstract: Surveillance system is widely used in the traffic
monitoring. The deployment of cameras is moving toward a
ubiquitous camera (UbiCam) environment. In our previous study, a
novel service, called GPS-VT, was firstly proposed by incorporating
global positioning system (GPS) and visual tracking techniques for
the UbiCam environment. The first prototype is called GODTA
(GPS-based Moving Object Detection and Tracking Approach). For a
moving person carried GPS-enabled mobile device, he can be
tracking when he enters the field-of-view (FOV) of a camera
according to his real-time GPS coordinate. In this paper, GPS-VT
service is applied to the tracking of vehicles. The moving speed of a
vehicle is much faster than a person. It means that the time passing
through the FOV is much shorter than that of a person. Besides, the
update interval of GPS coordinate is once per second, it is
asynchronous with the frame rate of the real-time image. The above
asynchronous is worsen by the network transmission delay. These
factors are the main challenging to fulfill GPS-VT service on a
vehicle.In order to overcome the influence of the above factors, a
back-propagation neural network (BPNN) is used to predict the
possible lane before the vehicle enters the FOV of a camera. Then, a
template matching technique is used for the visual tracking of a target
vehicle. The experimental result shows that the target vehicle can be
located and tracking successfully. The success location rate of the
implemented prototype is higher than that of the previous GODTA.
Abstract: This paper aims to propose a novel, robust, and simple method for obtaining a human 3D face model and camera pose (position and orientation) from a video sequence. Given a video sequence of a face recorded from an off-the-shelf digital camera, feature points used to define facial parts are tracked using the Active- Appearance Model (AAM). Then, the face-s 3D structure and camera pose of each video frame can be simultaneously calculated from the obtained point correspondences. This proposed method is primarily based on the combined approaches of Gradient Descent and Powell-s Multidimensional Minimization. Using this proposed method, temporarily occluded point including the case of self-occlusion does not pose a problem. As long as the point correspondences displayed in the video sequence have enough parallax, these missing points can still be reconstructed.
Abstract: Active vibration isolation systems are less commonly
used than passive systems due to their associated cost and power
requirements. In principle, semi-active isolation systems can deliver
the versatility, adaptability and higher performance of fully active
systems for a fraction of the power consumption. Various semi-active
control algorithms have been suggested in the past. This paper
studies the 4DOF model of semi-active suspension performance
controlled by on–off and continuous skyhook damping control
strategy. The frequency and transient responses of model are
evaluated in terms of body acceleration, roll angle and tire deflection
and are compared with that of a passive damper. The results show
that the semi-active system controlled by skyhook strategy always
provides better isolation than a conventional passively damped
system except at tire natural frequencies.
Abstract: The network of delivering commodities has been an important design problem in our daily lives and many transportation applications. The delivery performance is evaluated based on the system reliability of delivering commodities from a source node to a sink node in the network. The system reliability is thus maximized to find the optimal routing. However, the design problem is not simple because (1) each path segment has randomly distributed attributes; (2) there are multiple commodities that consume various path capacities; (3) the optimal routing must successfully complete the delivery process within the allowable time constraints. In this paper, we want to focus on the design optimization of the Multi-State Flow Network (MSFN) for multiple commodities. We propose an efficient approach to evaluate the system reliability in the MSFN with respect to randomly distributed path attributes and find the optimal routing subject to the allowable time constraints. The delivery rates, also known as delivery currents, of the path segments are evaluated and the minimal-current arcs are eliminated to reduce the complexity of the MSFN. Accordingly, the correct optimal routing is found and the worst-case reliability is evaluated. It has been shown that the reliability of the optimal routing is at least higher than worst-case measure. Two benchmark examples are utilized to demonstrate the proposed method. The comparisons between the original and the reduced networks show that the proposed method is very efficient.
Abstract: Nanowire arrays of copper with uniform diameters have
been synthesized by potentiostatic electrochemical metal deposition
(EMD) of copper sulphate and potassium chloride solution within
the nano-channels of porous Indium-Tin Oxide (ITO), also known as
Tin doped Indium Oxide templates. The nanowires developed were
fairly continuous with diameters ranging from 110-140 nm along
the entire length. Single as well as poly-crystalline copper wires
have been prepared by application of appropriate potential during the
EMD process. Scanning electron microscopy (SEM), high resolution
transmission electron microscopy (HRTEM), small angle electron
diffraction (SAED) and atomic force microscopy (AFM) were used
to characterize the synthesized nano wires at room temperature. The
electrochemical response of synthesized products was evaluated by
cyclic voltammetry while surface energy analysis was carried out
using a Goniometer.
Abstract: Phylogenies ; The evolutionary histories of groups of
species are one of the most widely used tools throughout the life
sciences, as well as objects of research with in systematic,
evolutionary biology. In every phylogenetic analysis reconstruction
produces trees. These trees represent the evolutionary histories of
many groups of organisms, bacteria due to horizontal gene transfer
and plants due to process of hybridization. The process of gene
transfer in bacteria and hybridization in plants lead to reticulate
networks, therefore, the methods of constructing trees fail in
constructing reticulate networks. In this paper a model has been
employed to reconstruct phylogenetic network in honey bee. This
network represents reticulate evolution in honey bee. The maximum
parsimony approach has been used to obtain this reticulate network.
Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: In this paper; we are interested principally in dynamic modelling of quadrotor while taking into account the high-order nonholonomic constraints in order to develop a new control scheme as well as the various physical phenomena, which can influence the dynamics of a flying structure. These permit us to introduce a new state-space representation. After, the use of Backstepping approach for the synthesis of tracking errors and Lyapunov functions, a sliding mode controller is developed in order to ensure Lyapunov stability, the handling of all system nonlinearities and desired tracking trajectories. Finally simulation results are also provided in order to illustrate the performances of the proposed controller.
Abstract: The American Health Level Seven (HL7) Reference Information Model (RIM) consists of six back-bone classes that have different specialized attributes. Furthermore, for the purpose of enforcing the semantic expression, there are some specific mandatory vocabulary domains have been defined for representing the content values of some attributes. In the light of the fact that it is a duplicated effort on spending a lot of time and human cost to develop and modify Clinical Information Systems (CIS) for most hospitals due to the variety of workflows. This study attempts to design and develop sharing RIM-based components of the CIS for the different business processes. Therefore, the CIS contains data of a consistent format and type. The programmers can do transactions with the RIM-based clinical repository by the sharing RIM-based components. And when developing functions of the CIS, the sharing components also can be adopted in the system. These components not only satisfy physicians- needs in using a CIS but also reduce the time of developing new components of a system. All in all, this study provides a new viewpoint that integrating the data and functions with the business processes, it is an easy and flexible approach to build a new CIS.
Abstract: The purpose of this study is to design a portable virtual
piano. By utilizing optical fiber gloves and the virtual piano software
designed by this study, the user can play the piano anywhere at any
time. This virtual piano consists of three major parts: finger tapping
identification, hand movement and positioning identification, and
MIDI software sound effect simulation. To play the virtual piano, the
user wears optical fiber gloves and simulates piano key tapping
motions. The finger bending information detected by the optical fiber
gloves can tell when piano key tapping motions are made. Images
captured by a video camera are analyzed, hand locations and moving
directions are positioned, and the corresponding scales are found. The
system integrates finger tapping identification with information about
hand placement in relation to corresponding piano key positions, and
generates MIDI piano sound effects based on this data. This
experiment shows that the proposed method achieves an accuracy rate
of 95% for determining when a piano key is tapped.
Abstract: This paper proposes a novel multi-format stream grid
architecture for real-time image monitoring system. The system, based
on a three-tier architecture, includes stream receiving unit, stream
processor unit, and presentation unit. It is a distributed computing and
a loose coupling architecture. The benefit is the amount of required
servers can be adjusted depending on the loading of the image
monitoring system. The stream receive unit supports multi capture
source devices and multi-format stream compress encoder. Stream
processor unit includes three modules; they are stream clipping
module, image processing module and image management module.
Presentation unit can display image data on several different platforms.
We verified the proposed grid architecture with an actual test of image
monitoring. We used a fast image matching method with the
adjustable parameters for different monitoring situations. Background
subtraction method is also implemented in the system. Experimental
results showed that the proposed architecture is robust, adaptive, and
powerful in the image monitoring system.
Abstract: A measurement system was successfully fabricated to
detect ion concentrations (hydrogen and chlorine) in this study.
PIC18F4520, the microcontroller was used as the control unit in the
measurement system. The measurement system was practically used
to sense the H+ and Cl- in different examples, and the pH and pCl
values were exhibited on real-time LCD display promptly. In the study,
the measurement method is used to judge whether the response voltage
is stable. The change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for H+
measurement, and the above condition is established only 6 sec.
Besides, the change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for Clmeasurement,
and the above condition is established only 5 sec.
Furthermore, the average error quantities would also be considered,
and they are 0.05 and 0.07 for measurements of pH and pCl values,
respectively.