Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: This paper proposes a rotational invariant texture
feature based on the roughness property of the image for psoriasis
image analysis. In this work, we have applied this feature for image
classification and segmentation. The fuzzy concept is employed to
overcome the imprecision of roughness. Since the psoriasis lesion is
modeled by a rough surface, the feature is extended for calculating
the Psoriasis Area Severity Index value. For classification and
segmentation, the Nearest Neighbor algorithm is applied. We have
obtained promising results for identifying affected lesions by using
the roughness index and severity level estimation.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: Wind energy offers a significant advantage such as no
fuel costs and no emissions from generation. However, wind energy
sources are variable and non-dispatchable. The utility grid is able to
accommodate the variability of wind in smaller proportion along with
the daily load. However, at high penetration levels, the variability can
severely impact the utility reserve requirements and the cost
associated with it. In this paper the impact of wind energy is
evaluated in detail in formulating the total utility cost. The objective
is to minimize the overall cost of generation while ensuring the
proper management of the load. Overall cost includes the curtailment
cost, reserve cost and the reliability cost, as well as any other penalty
imposed by the regulatory authority. Different levels of wind
penetrations are explored and the cost impacts are evaluated. As the
penetration level increases significantly, the reliability becomes a
critical question to be answered. Here we increase the penetration
from the wind yet keep the reliability factor within the acceptable
limit provided by NERC. This paper uses an economic dispatch (ED)
model to incorporate wind generation into the power grid. Power
system costs are analyzed at various wind penetration levels using
Linear Programming. The goal of this study is show how the
increases in wind generation will affect power system economics.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: A Disaster Management System (DMS) is very important for countries with multiple disasters, such as Chile. In the world (also in Chile)different disasters (earthquakes, tsunamis, volcanic eruption, fire or other natural or man-made disasters) happen and have an effect on the population. It is also possible that two or more disasters occur at the same time. This meansthata multi-risk situation must be mastered. To handle such a situation a Decision Support System (DSS) based on multiagents is a suitable architecture. The most known DMSs are concernedwith only a singledisaster (sometimes thecombination of earthquake and tsunami) and often with a particular disaster. Nevertheless, a DSS helps for a better real-time response. Analyze the existing systems in the literature and expand them for multi-risk disasters to construct a well-organized system is the proposal of our work. The here shown work is an approach of a multi-risk system, which needs an architecture and well defined aims. In this moment our study is a kind of case study to analyze the way we have to follow to create our proposed system in the future.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: Much attention is paid to the development of space
branch in Kazakhstan at present. Two Earth remote sensing satellites
of Kazakhstan have been launched successfully. Many projects
related to the development of components for satellite are carried in
Kazakhstan, in particular the project related to the development of
star tracker experimental model. It is planned to use the results of this
project for development of star tracker prototype in the future. This
article describes the main stages of development of star tracker
experimental model.
Abstract: The concept of technology as well as itself has
evolved continuously over time, such that, nowadays, this concept is
still marked by myths and realities. Even the concept of science is
frequently misunderstood as technology. In this way, this paper
presents different forms of interpretation of the concept of technology
in the course of history, as well as the social and cultural aspects
associated with it, through an analysis made by means of insights
from sociological studies of science and technology and its multiple
relations with society. Through the analysis of contents, the paper
presents a classification of how technology is interpreted in the social
sphere and search channel efforts to show how a broader
understanding can contribute to better interpretations of how
scientific and technological development influences the environment
in which we operate. The text also presents a particular point of view
for the interpretation of the concept from the analysis throughout the
whole work.
Abstract: Although there had been a many studies that shows
the impact of air pollution on physical health, comparatively less was
known of human behavioral responses and annoyance impacts.
Annoyance caused by air pollution is a public health problem because
it can be an ambient stressor causing stress and disease and can affect
quality of life. The objective of this work is to evaluate the
annoyance caused by air pollution in two different industrialized
urban areas, Dunkirk (France) and Vitoria (Brazil). The populations
of these cities often report feeling annoyed by dust. Surveys were
conducted, and the collected data were analyzed using statistical
analyses. The results show that sociodemographic variables,
importance of air quality, perceived industrial risk, perceived air
pollution and occurrence of health problems play important roles in
the perceived annoyance. These results show the existence of a
common problem in geographically distant areas and allow
stakeholders to develop prevention strategies.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: A quartz crystal microbalance (QCM) nanosensor was developed to detect lysozyme enzyme by functionalizing its gold surface with the attachment of poly(methacroyl-L-phenylalanine) (PMAPA) nanoparticles. PMAPA was chosen as a hydrophobic matrix. The hydrophobic nanoparticles were synthesized by micro-emulsion polymerization method. Hydrophobic QCM nanosensor was tested for real time detection of lysozyme enzyme from aqueous solution. The kinetic and affinity studies were determined by using lysozyme solutions with different concentrations. The responses related with mass (Δm) and frequency (Δf) shifts were used to evaluate adsorption properties.
Abstract: This study presents the moisture variations of
unbound layers from April 2012 to January 2014 in the Interstate 40
(I-40) pavement section in New Mexico. Three moisture probes were
installed at different layers inside the pavement which measure the
continuous moisture variations of the unbound layers. Data show that
the moisture contents of unbound layers are typically constant
throughout the day and month unless there is rainfall. Moisture
contents of all unbound layers change with rainfall. Change in ground
water table may affect the moisture content of unbound layers which
has not been investigated in this study. In addition, the Level 3
predictions of moisture contents using the Pavement Mechanistic-
Empirical (ME) Design software were compared and found quite
reasonable. However, results presented in the current study may not
be applicable for pavement in other regions.
Abstract: IEEE 802.16 (WiMAX) aims to present high speed
wireless access to cover wide range coverage. The base station (BS)
and the subscriber station (SS) are the main parts of WiMAX.
WiMAX uses either Point-to-Multipoint (PMP) or mesh topologies.
In the PMP mode, the SSs connect to the BS to gain access to the
network. However, in the mesh mode, the SSs connect to each other
to gain access to the BS.
The main components of QoS management in the 802.16 standard
are the admission control, buffer management and packet scheduling.
In this paper, we use QualNet 5.0.2 to study the performance of
different scheduling schemes, such as WFQ, SCFQ, RR and SP when
the numbers of SSs increase. We find that when the number of SSs
increases, the average jitter and average end-to-end delay is increased
and the throughput is reduced.
Abstract: The eccentric connectivity index based on degree and
eccentricity of the vertices of a graph is a widely used graph invariant
in mathematics.
In this paper, we present the explicit eccentric connectivity index,
first and second Zagreb indices for a Corona graph and sub divisionrelated
corona graphs.
Abstract: In review the generalized data about different methods
of synthesis of biological activity aminated hydroxyanthraquinones is
presented. The basic regularity of a synthesis is analyzed. Action of
temperature, pH, solubility, catalysts and other factors on a reaction
product yield is revealed.
Abstract: The effects of basil and/or chamomile seed
supplementation on the growth of Hubbard broiler chicks were
evaluated. The antioxidant effects of these supplements were also
assessed. 120 1-day-old broiler chicks were randomly divided into
four equal groups. The control group (group 1) was fed a basal diet
(BD) without supplementation. Groups 2, 3, and 4 were fed the BD
supplemented with 10g basil, 10g chamomile, and 5g basil plus 5g
chamomile per kg of food, respectively. Basil supplementation alone
or in combination with chamomile non-significantly (P≥0.05)
increased final body weight (3.2% and 0.3%, respectively) and
weight gain (3.5% and 3.6%, respectively) over the experimental
period. Chamomile supplementation alone non-significantly (P≥0.05)
reduced final body weight and weight gain over the experimental
period by 1.7% and 1.7%, respectively. In comparison to the control
group, herbal seed supplementation reduced feed intake and
improved the feed conversion and protein efficiency ratios. In
general, basil seed supplementation stimulated chicken growth and
improved the feed efficiency more effectively than chamomile seed
supplementation. The antioxidant activities of basil and/or chamomile
supplementation were examined in the thymus, bursa, and spleen. In
chickens that received supplements, the level of malondialdehyde
was significantly decreased, whereas the activities of glutathione,
superoxide dismutase, and catalase were significantly increased
(P
Abstract: Based on the experimental data, the impact of
resistance and reactance of the winding, as well as the magnetic
permeability of the magnetic circuit steel material on the value of the
electromotive force of the induction converter is investigated. The
obtained results allow estimating the main technological spreads and
determining the maximum level of the electromotive force change.
By the method of experiment planning, the expression of a
polynomial for the electromotive force which can be used to estimate
the adequacy of mathematical models to be used at the investigation
and design of induction converters is obtained.
Abstract: Our goal is development of an algorithm capable of
predicting the directional trend of the Standard and Poor’s 500 index
(S&P 500). Extensive research has been published attempting to
predict different financial markets using historical data testing on an
in-sample and trend basis, with many authors employing excessively
complex mathematical techniques. In reviewing and evaluating these
in-sample methodologies, it became evident that this approach was
unable to achieve sufficiently reliable prediction performance for
commercial exploitation. For these reasons, we moved to an out-ofsample
strategy based on linear regression analysis of an extensive
set of financial data correlated with historical closing prices of the
S&P 500. We are pleased to report a directional trend accuracy of
greater than 55% for tomorrow (t+1) in predicting the S&P 500.
Abstract: Sustainability and eco-friendly requirement of
engineering materials are sort for in recent times, thus giving rise to
the development of bio-composites. However, the natural fibres to
matrix interface interactions remain a key issue in getting the desired
mechanical properties from such composites. Treatment of natural
fibres is essential in improving matrix to filler adhesion, hence
improving its mechanical properties. In this study, investigations
were carried out to determine the effect of sodium hydroxide
treatment on the tensile, flexural, impact and hardness properties of
crushed and uncrushed Luffa cylindrica fibre reinforced recycled low
density polyethylene composites. The LC (Luffa cylindrica) fibres
were treated with 0%, 2%, 4%, 6%, 8% and 10% wt. sodium
hydroxide (NaOH) concentrations for a period of 24 hours under
room temperature conditions. A formulation ratio of 80/20 g (matrix
to reinforcement) was maintained for all developed samples. Analysis
of the results showed that the uncrushed luffa fibre samples gave
better mechanical properties compared with the crushed luffa fibre
samples. The uncrushed luffa fibre composites had a maximum
tensile and flexural strength of 7.65 MPa and 17.08 Mpa respectively
corresponding to a young modulus and flexural modulus of 21.08
MPa and 232.22 MPa for the 8% and 4% wt. NaOH concentration
respectively. Results obtained in the research showed that NaOH
treatment with the 8% NaOH concentration improved the mechanical
properties of the LC fibre reinforced composites when compared with
other NaOH treatment concentration values.