Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: Modelling of the earth's surface and evaluation of
urban environment, with 3D models, is an important research topic.
New stereo capabilities of high resolution optical satellites images,
such as the tri-stereo mode of Pleiades, combined with new image
matching algorithms, are now available and can be applied in urban
area analysis. In addition, photogrammetry software packages gained
new, more efficient matching algorithms, such as SGM, as well as
improved filters to deal with shadow areas, can achieve more dense
and more precise results.
This paper describes a comparison between 3D data extracted
from tri-stereo and dual stereo satellite images, combined with pixel
based matching and Wallis filter. The aim was to improve the
accuracy of 3D models especially in urban areas, in order to assess if
satellite images are appropriate for a rapid evaluation of urban
environments.
The results showed that 3D models achieved by Pleiades tri-stereo
outperformed, both in terms of accuracy and detail, the result
obtained from a Geo-eye pair. The assessment was made with
reference digital surface models derived from high resolution aerial
photography. This could mean that tri-stereo images can be
successfully used for the proposed urban change analyses.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: This paper presents an adaptive thermal comfort
model study in the tropical country of Malaysia. A number of
researchers have been interested in applying the adaptive thermal
comfort model to different climates throughout the world, but so far
no study has been performed in Malaysia. For the use as a thermal
comfort model, which better applies to hot and humid climates, the
adaptive thermal comfort model was developed as part of this
research by using the collected results from a large field study in six
lecture halls with 178 students. The relationship between the
operative temperature and behavioral adaptations was determined. In
the developed adaptive model, the acceptable indoor neutral
temperatures lay within the range of 23.9-26.0C, with outdoor
temperatures ranging between 27.0-34.6C. The most comfortable
temperature for students in lecture hall was 25.7C.
Abstract: Sandwich structure composites produced by epoxy
core and aluminium skin were developed as potential building
materials. Interface bonding between core and skin was controlled by
varying kenaf content. Five different weight percentage of kenaf
loading ranging from 10 wt% to 50 wt% were employed in the core
manufacturing in order to study the mechanical properties of the
sandwich composite. Properties of skin aluminium with epoxy were
found to be affected by drying time of the adhesive. Mechanical
behavior of manufactured sandwich composites in relation with
properties of constituent materials was studied. It was found that 30
wt% of kenaf loading contributed to increase the flexural strength and
flexural modulus up to 102 MPa and 32 GPa, respectively. Analysis
were done on the flatwise and edgewise compression test. For
flatwise test, it was found that 30 wt% of fiber loading could
withstand maximum force until 250 kN, with compressive strength
results at 96.94 MPa. However, at edgewise compression test, the
sandwich composite with same fiber loading only can withstand 31
kN of the maximum load with 62 MPa of compressive strength
results.
Abstract: The 6th version of Universal modeling method for
centrifugal compressor stage calculation is described. Identification
of the new mathematical model was made. As a result of
identification the uniform set of empirical coefficients is received.
The efficiency definition error is 0,86 % at a design point. The
efficiency definition error at five flow rate points (except a point of
the maximum flow rate) is 1,22 %. Several variants of the stage with
3D impellers designed by 6th version program and quasi threedimensional
calculation programs were compared by their gas
dynamic performances CFD (NUMECA FINE TURBO).
Performance comparison demonstrated general principles of design
validity and leads to some design recommendations.
Abstract: Fiber Bragg optic sensor is embedded in composite
material to detect and monitor the damage that occurs in composite
structures. In this paper, we deal with the mode-Ι delamination to
determine the material strength to crack propagation, using the
coupling mode theory and T-matrix method to simulate the FBGs
spectrum for both uniform and non-uniform strain distribution. The
double cantilever beam test is modeled in FEM to determine the
longitudinal strain. Two models are implemented, the first is the
global half model, and the second is the sub-model to represent the
FBGs with higher refined mesh. This method can simulate damage in
composite structures and converting strain to a wavelength shifting in
the FBG spectrum.
Abstract: This study concerned the dynamic behavior of the
wind turbine rotor. Before all we have studied the loads applied to the
rotor, which allows the knowledge their effect on the fatigue, also
studied the rotor with longitudinal crack in order to determine stress,
strain and displacement. Firstly we compared the first six modes
shapes between cracking and uncracking of HAWT rotor. Secondly
we show show evolution of first six natural frequencies with
longitudinal crack propagation. Finally we conclude that the residual
change in the natural frequencies can be used as in shaft crack
diagnosis predictive maintenance.
Abstract: Physical properties of uranium dinitride (UN2) were
investigated in detail using first principle calculations based on
density functional theory (DFT). To study the strong correlation
effects due to 5f uranium valence electrons, the on-site coulomb
interaction correction U via the Hubbard-like term (DFT+U) was
employed. The UN2 structural, mechanical and thermodynamic
properties were calculated within DFT and Various U of DFT+U
approach.
The Perdew–Burke–Ernzerhof (PBE.5.2) version of the
generalized gradient approximation (GGA) is used to describe the
exchange-correlation with the projector-augmented wave (PAW)
pseudo potentials.
A comparative study shows that results are improved by using the
Hubbard formalism for a certain U value correction like the structural
parameter. For some physical properties the variation versus
Hubbard-U is strong like Young modulus but for others it is weakly
noticeable such as bulk modulus.
We noticed also that from U=7.5 eV, elastic results don’t agree
with the cubic cell because of the C44 values which turn out to be
negative.
Abstract: The present paper summarizes the analysis of the
request for consultation of information and data on industrial
emissions made publicly available on the web site of the Ministry of
Environment, Land and Sea on integrated pollution prevention and
control from large industrial installations, the so called “AIA Portal”.
As a matter of fact, a huge amount of information on national
industrial plants is already available on internet, although it is usually
proposed as textual documentation or images.
Thus, it is not possible to access all the relevant information
through interoperability systems and also to retrieval relevant
information for decision making purposes as well as rising of
awareness on environmental issue.
Moreover, since in Italy the number of institutional and private
subjects involved in the management of the public information on
industrial emissions is substantial, the access to the information is
provided on internet web sites according to different criteria; thus, at
present it is not structurally homogeneous and comparable.
To overcome the mentioned difficulties in the case of the
Coordinating Committee for the implementation of the Agreement
for the industrial area in Taranto and Statte, operating before the
IPPC permit granting procedures of the relevant installation located
in the area, a big effort was devoted to elaborate and to validate data
and information on characterization of soil, ground water aquifer and
coastal sea at disposal of different subjects to derive a global
perspective for decision making purposes. Thus, the present paper
also focuses on main outcomes matured during such experience.
Abstract: Collaborative technologies or software known as
groupware are key enabling tools for communication, collaboration
and co-ordination among individuals, work groups and businesses.
Available reviews of the groupware literature are very few,
and mostly neither systematic nor recent.
This paper is an effort to fill this gap, and to provide researchers,
with a more up-to-date and wide systematic literature review. For this
purpose, 1087 scholarly articles, published from 1990 to 2013, on the
topic of groupware, were collected by the literature search. The study
here adopted the systematic approach of lexical analysis for the
analysis of those articles.
Abstract: Verification and Validation of Simulated Process
Model is the most important phase of the simulator life cycle.
Evaluation of simulated process models based on Verification and
Validation techniques checks the closeness of each component model
(in a simulated network) with the real system/process with respect to
dynamic behaviour under steady state and transient conditions. The
process of Verification and Validation helps in qualifying the process
simulator for the intended purpose whether it is for providing
comprehensive training or design verification. In general, model
verification is carried out by comparison of simulated component
characteristics with the original requirement to ensure that each step
in the model development process completely incorporates all the
design requirements. Validation testing is performed by comparing
the simulated process parameters to the actual plant process
parameters either in standalone mode or integrated mode.
A Full Scope Replica Operator Training Simulator for PFBR -
Prototype Fast Breeder Reactor has been developed at IGCAR,
Kalpakkam, INDIA named KALBR-SIM (Kalpakkam Breeder
Reactor Simulator) where in the main participants are
engineers/experts belonging to Modeling Team, Process Design and
Instrumentation & Control design team. This paper discusses about
the Verification and Validation process in general, the evaluation
procedure adopted for PFBR operator training Simulator, the
methodology followed for verifying the models, the reference
documents and standards used etc. It details out the importance of
internal validation by design experts, subsequent validation by
external agency consisting of experts from various fields, model
improvement by tuning based on expert’s comments, final
qualification of the simulator for the intended purpose and the
difficulties faced while co-coordinating various activities.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: This work presents synthesis of α,ω-dithienyl
terminated poly(ethylene glycol) (PEGTh) capable for further chain
extension by either chemical or electrochemical polymeriztion.
PEGTh was characterized by FTIR and 1H-NMR. Further
copolymerization of PEGTh and pyrrole (Py) was performed by
chemical oxidative polymerization using ceric (IV) salt as an oxidant
(PPy-PEGTh). PEG without end group modification was used
directly to prepare copolymers with Py by Ce (IV) salt (PPy-PEG).
Block copolymers with mole ratio of pyrrole to PEGTh (PEG) 50:1
and 10:1 were synthesized. The electrical conductivities of
copolymers PPy-PEGTh and PPy-PEG were determined by four
point probe technique. Influence of the synthetic route and content of
the insulating segment on conductivity and yield of the copolymers
were investigated.
Abstract: Different tools and technologies were implemented
for Crisis Response and Management (CRM) which is generally
using available network infrastructure for information exchange.
Depending on type of disaster or crisis, network infrastructure could
be affected and it could not be able to provide reliable connectivity.
Thus any tool or technology that depends on the connectivity could
not be able to fulfill its functionalities. As a solution, a new message
exchange framework has been developed. Framework provides
offline/online information exchange platform for CRM Information
Systems (CRMIS) and it uses XML compression and packet
prioritization algorithms and is based on open source web
technologies. By introducing offline capabilities to the web
technologies, framework will be able to perform message exchange
on unreliable networks. The experiments done on the simulation
environment provide promising results on low bandwidth networks
(56kbps and 28.8 kbps) with up to 50% packet loss and the solution is
to successfully transfer all the information on these low quality
networks where the traditional 2 and 3 tier applications failed.
Abstract: Eucalyptus species are well reputed for their
traditional use in Asia as well as in other parts of the world; therefore,
the present study was designed to investigate the antimicrobial and
antioxidant activities associated with essential oils from different
Eucalyptus species. Essential oils from the leaves of six Eucalyptus
species, including: Eucalyptus woodwardi, Eucalyptus stricklandii,
Eucalyptus salubris, Eucalyptus sargentii, Eucalyptus torquata and
Eucalyptus wandoo were separated by hydrodistillation and dried
over anhydrous sodium sulphate. DPPH, ferric reducing antioxidant
power, and hydroxyl radical scavenging activity assays were carried
out to evaluate the antioxidant potential of the oils. The results
indicate that examined oils exhibit substantial antioxidant activities
relative to ascorbic acid. Previously, these oils were evaluated for
their antimicrobial activities, against wide range of bacterial and
fungal strains, and they were shown to possess significant
antimicrobial activities. In this study, further investigation into the
growth kinetics of oil-treated microbial cultures was conducted. The
results clearly demonstrate that the microbial growth was markedly
inhibited when treated with sub-MIC concentrations of the oils.
Taken together, the results obtained indicate a high potential of the
examined essential oils as bioactive oils, for nutraceutical and
medical applications, possessing significant antioxidant and anti
microbial activities.
Abstract: Vegetation affects the mean and turbulent flow
structure. It may increase flood risks and sediment transport.
Therefore, it is important to develop analytical approaches for the bed
shear stress on vegetated bed, to predict resistance caused by
vegetation. In the recent years, experimental and numerical models
have both been developed to model the effects of submerged
vegetation on open-channel flow. In this paper, different analytic
models are compared and tested using the criteria of deviation, to
explore their capacity for predicting the mean velocity and select the
suitable one that will be applied in real case of rivers. The
comparison between the measured data in vegetated flume and
simulated mean velocities indicated, a good performance, in the case
of rigid vegetation, whereas, Huthoff model shows the best
agreement with a high coefficient of determination (R2=80%) and the
smallest error in the prediction of the average velocities.
Abstract: In the present work, the alloy of Bismuth-lead is
prepared on the basis of percentage of molecular weight 9:1, 5:5 and
1:9 ratios and grown by Zone- Refining Technique under a vacuum
atmosphere. The EDAX of these samples are done and the results are
reported. Micro hardness test has been used as an alternative test for
measuring material’s tensile properties. The effect of temperature and
load on the hardness of the grown alloy has been studied. Further the
comparative studies of work hardening coefficients are reported.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.