Abstract: Operations research science (OR) deals with good
success in developing and applying scientific methods for problem
solving and decision-making. However, by using OR techniques, we
can enhance the use of computer decision support systems to achieve
optimal management for institutions. OR applies comprehensive
analysis including all factors that effect on it and builds mathematical
modeling to solve business or organizational problems. In addition, it
improves decision-making and uses available resources efficiently.
The adoption of OR by universities would definitely contributes to
the development and enhancement of the performance of OR
techniques. This paper provides an understanding of the structures,
approaches and models of OR in problem solving and decisionmaking.
Abstract: This paper presents a new structure of microstrip band
pass filter (BPF) based on coupled stepped impedance resonators.
Each filter consists of two coupled stepped impedance resonators
connected to microstrip feed lines. The coupled junction is utilized to
connect the two BPFs to the antenna. This two band pass filters are
designed and simulated to operate for the digital communication
system (DCS) and Industrial Scientific and Medical (ISM) bands at
1.8 GHz and 2.45 GHz respectively. The proposed circuit presents
good performances with an insertion loss lower than 2.3 dB and
isolation between the two channels greater than 21 dB. The prototype
of the optimized diplexer have been investigated numerically by
using ADS Agilent and verified with CST microwave software.
Abstract: Carbon fiber reinforced polymersarewidely used to strengthen steel structural elements. These structural elements are normally subjected to static, dynamic and fatigue loadings during their life-time. CFRP laminate is commonly used to strengthen these structures under the subjected loads. A number of studies have focused on the characteristics of CFRP sheets bonded to steel members under static, dynamic and fatigue loadings. However, there is a gap in understanding the bonding behavior between CFRP laminates and steel members under impact loading. This paper shows the effect of high load rates on this bond. CFRP laminate CFK 150/2000 was used to strengthen steel joints using Araldite 420 epoxy. The results show that applying a high load rate significantly affects the bond strength but has little influence on the effective bond length.
Abstract: In this study the instability problem of a modified
Taylor-Couette flow between two vertical coaxial cylinders of radius
R1, R2 is considered. The modification is based on the wavy shape of
the inner cylinder surface, where inner cylinders with different
surface amplitude and wavelength are used. The study aims to
discover the effect of the inner surface geometry on the instability
phenomenon that undergoes Taylor-Couette flow. The study reveals
that the transition processes depends strongly on the amplitude and
wavelength of the inner cylinder surface and resulting in flow
instabilities that are strongly different from that encountered in the
case of the classical Taylor-Couette flow.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: Many wireless sensor network applications require
K-coverage of the monitored area. In this paper, we propose a
scalable harmony search based algorithm in terms of execution
time, K-Coverage Enhancement Algorithm (KCEA), it attempts to
enhance initial coverage, and achieve the required K-coverage degree
for a specific application efficiently. Simulation results show that
the proposed algorithm achieves coverage improvement of 5.34%
compared to K-Coverage Rate Deployment (K-CRD), which achieves
1.31% when deploying one additional sensor. Moreover, the proposed
algorithm is more time efficient.
Abstract: Container handling problems at container terminals
are NP-hard problems. This paper presents an approach using
discrete-event simulation modeling to optimize solution for storage
space allocation problem, taking into account all various interrelated
container terminal handling activities. The proposed approach is
applied on a real case study data of container terminal at Alexandria
port. The computational results show the effectiveness of the
proposed model for optimization of storage space allocation in
container terminal where 54% reduction in containers handling time
in port is achieved.
Abstract: The exact theoretical expression describing the
probability distribution of nonlinear sea-surface elevations derived
from the second-order narrowband model has a cumbersome form
that requires numerical computations, not well-disposed to theoretical
or practical applications. Here, the same narrowband model is reexamined
to develop a simpler closed-form approximation suitable
for theoretical and practical applications. The salient features of the
approximate form are explored, and its relative validity is verified
with comparisons to other readily available approximations, and
oceanic data.
Abstract: A field experiment was carried out at Arab El-
Awammer Research Station, Agric. Res. Center. Assiut Governorate
during summer seasons of 2013 and 2014. The present study assessed
the effect of cowpea with maize intercropping on yield and its
components. The experiment comprised of three treatments (sole
cowpea, sole maize and cowpea-maize intercrop). The experimental
design was a randomized complete block with four replications.
Results indicated that intercropped maize plants with cowpea,
exhibited greater potentiality and resulted in higher values of most of
the studied criteria viz., plant height, number of ears/plant, number of
rows/ear, number of grains/row, grains weight/ear, 100–grain weight
and straw and grain yields. Fresh and dry forage yields of cowpea
were lower in intercropping with maize than sole. Furthermore, the
combined of the two seasons revealed that the total Land Equivalent
Ratio (LER) between cowpea and maize was 1.65. The Aggressivity
(A) maize was 0.45 and cowpea was -0.45. This showed that maize
was the dominant crop, whereas cowpea was the dominated. The
Competitive Ratio (CR) indicated that maize more competitive than
cowpea, maize was 1.75 and cowpea was 0.57. The Actual Yield
Loss (AYL) maize was 0.05 and cowpea was -0.40. The Monetary
Advantage Index (MAI) was 2360.80.
Abstract: Medulloblastoma (MB) is one of the most prevalent
brain tumours among paediatrics. Although its management has
evolved over time still there is need to find new therapeutic targets
for MB that can result in less normal tissue toxicity while improving
survival and reducing recurrence. This literature review is aimed at
finding new potential therapeutic targets for MB focusing on viruses
that can be used as potential targets for MB. The review also gives an
over-view of management of paediatric Medulloblastoma focusing on
Radiotherapy management.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.
Abstract: The tomato is a very important crop, whose
cultivation in the Mediterranean basin is severely affected by the
phytoparasitic weed Phelipanche ramosa. The semiarid regions of
the world are considered the main areas where this parasitic weed is
established causing heavy infestation as it is able to produce high
numbers of seeds (up to 500,000 per plant), which remain viable for
extended period (more than 20 years). In this paper the results
obtained from eleven treatments in order to control this parasitic
weed including chemical, agronomic, biological and biotechnological
methods compared with the untreated test under two plowing depths
(30 and 50 cm) are reported. The split-plot design with 3 replicates
was adopted. In 2014 a trial was performed in Foggia province
(southern Italy) on processing tomato (cv Docet) grown in the field
infested by Phelipanche ramosa. Tomato seedlings were transplant
on May 5, on a clay-loam soil. During the growing cycle of the
tomato crop, at 56-78 and 92 days after transplantation, the number
of parasitic shoots emerged in each plot was detected. At tomato
harvesting, on August 18, the major quantity-quality yield parameters
were determined (marketable yield, mean weight, dry matter, pH,
soluble solids and color of fruits). All data were subjected to analysis
of variance (ANOVA) and the means were compared by Tukey's test.
Each treatment studied did not provide complete control against
Phelipanche ramosa. However, among the different methods tested,
some of them which Fusarium, gliphosate, radicon biostimulant and
Red Setter tomato cv (improved genotypes obtained by Tilling
technology) under deeper plowing (50 cm depth) proved to mitigate
the virulence of the Phelipanche ramose attacks. It is assumed that
these effects can be improved combining some of these treatments
each other, especially for a gradual and continuing reduction of the
“seed bank” of the parasite in the soil.
Abstract: Cavitation in cryogenic liquids is widely present in
contemporary science. In the current study, we re-examine a
previously validated acoustic cavitation model which was developed
for a gas bubble in liquid water. Furthermore, simulations of
cryogenic fluids including the thermal effect, the effect of acoustic
pressure amplitude and the frequency of sound field on the bubble
dynamics are presented. A gas bubble (Helium) in liquids Nitrogen,
Oxygen and Hydrogen in an acoustic field at ambient pressure and
low temperature is investigated numerically. The results reveal that
the oscillation of the bubble in liquid Hydrogen fluctuates more than
in liquids Oxygen and Nitrogen. The oscillation of the bubble in
liquids Oxygen and Nitrogen is approximately similar.
Abstract: This work presents a new planar multiband antenna
based on fractal geometry. This structure is optimized and validated
into simulation by using CST-MW Studio. To feed this antenna we
have used a CPW line which makes it easy to be incorporated with
integrated circuits. The simulation results presents a good matching
input impedance and radiation pattern in the GSM band at 900 MHz
and ISM band at 2.4 GHz. The final structure is a dual band fractal
antenna with 70 x 70 mm² as a total area by using an FR4 substrate.
Abstract: This paper presents a novel design of a microstrip
fractal antenna based on the use of Sierpinski triangle shape, it’s
designed and simulated by using FR4 substrate in the operating
frequency bands (GPS, WiMAX), the design is a fractal antenna with
a modified ground structure. The proposed antenna is simulated and
validated by using CST Microwave Studio Software, the simulated
results presents good performances in term of radiation pattern and
matching input impedance.
Abstract: Knowledge management is considered as an important
factor in improving health care services. KM facilitates the transfer of
existing knowledge and the development of new knowledge in
hospitals. This paper reviews practices adopted by doctors in Kuwait
for capturing, sharing, and generating knowledge. It also discusses
the perceived impact of KM practices on performance of hospitals.
Based on a survey of 277 doctors, the study found that KM practices
among doctors in the sampled hospitals were not very effective. Little
attention was paid to the main activities that support the transfer of
expertise among doctors in hospitals. However, as predicted by
previous studies, good km practices were perceived by doctors to
have a positive impact on performance of hospitals. It was concluded
that through effective KM practices hospitals could improve the
services they provide. Documentation of best practices and capturing
of lessons learnt for re-use of knowledge could help transform the
hospitals into learning organizations.
Abstract: This study investigates how AlGaAs/GaAs thin film
solar cells perform under varying global solar spectrum due to the
changes of environmental parameters such as the air mass and the
atmospheric turbidity. The solar irradiance striking the solar cell is
simulated using the spectral irradiance model SMARTS2 (Simple
Model of the Atmospheric Radiative Transfer of Sunshine) for clear
skies on the site of Setif (Algeria). The results show a reduction in the
short circuit current due to increasing atmospheric turbidity, it is
63.09% under global radiation. However increasing air mass leads to
a reduction in the short circuit current of 81.73%. The efficiency
decreases with increasing atmospheric turbidity and air mass.
Abstract: To develop AZ91D magnesium alloys with improved
properties, we have applied TiN and VN/TiN multilayer coatings
using DC magnetron sputter technique. Coating structure, surface
morphology, chemical bonding and corrosion resistance of coatings
were analyzed by x-ray diffraction (XRD), scanning electron
microscope (SEM), x-ray photoelectron spectroscopy (XPS), and
tafel extrapolation method, respectively. XPS analysis reveal that VN
overlayer reacts with oxygen at the VN/TiN interface and forms more
stable TiN layer. Morphological investigations and the corrosion
results show that VN/TiN multilayer thin film coatings are quite
effective to optimize the corrosion resistance of Mg alloys.
Abstract: This work was one of the tasks of the
Manufacturing2Client project, whose objective was to develop a
frontal deflector to be commercialized in the automotive industry,
using new project and manufacturing methods. In this task, in
particular, it was proposed to develop the ability to predict
computationally the aerodynamic influence of flow in vehicles, in an
effort to reduce fuel consumption in vehicles from class 3 to 8. With
this aim, two deflector models were developed and their aerodynamic
performance analyzed. The aerodynamic study was done using the
Computational Fluid Dynamics (CFD) software Ansys CFX and
allowed the calculation of the drag coefficient caused by the vehicle
motion for the different configurations considered. Moreover, the
reduction of diesel consumption and carbon dioxide (CO2) emissions
associated with the optimized deflector geometry could be assessed.
Abstract: The final step to complete the “Analytical Systems
Engineering Process” is the “Allocated Architecture” in which all
Functional Requirements (FRs) of an engineering system must be
allocated into their corresponding Physical Components (PCs). At
this step, any design for developing the system’s allocated
architecture in which no clear pattern of assigning the exclusive
“responsibility” of each PC for fulfilling the allocated FR(s) can be
found is considered a poor design that may cause difficulties in
determining the specific PC(s) which has (have) failed to satisfy a
given FR successfully. The present study utilizes the Axiomatic
Design method principles to mathematically address this problem and
establishes an “Axiomatic Model” as a solution for reaching good
alternatives for developing the allocated architecture. This study
proposes a “loss Function”, as a quantitative criterion to monetarily
compare non-ideal designs for developing the allocated architecture
and choose the one which imposes relatively lower cost to the
system’s stakeholders. For the case-study, we use the existing design
of U. S. electricity marketing subsystem, based on data provided by
the U.S. Energy Information Administration (EIA). The result for
2012 shows the symptoms of a poor design and ineffectiveness due to
coupling among the FRs of this subsystem.