Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: Red blood cells (RBC) are the most common types of
blood cells and are the most intensively studied in cell biology. The
lack of RBCs is a condition in which the amount of hemoglobin level
is lower than normal and is referred to as “anemia”. Abnormalities in
RBCs will affect the exchange of oxygen. This paper presents a
comparative study for various techniques for classifying the RBCs as
normal or abnormal (anemic) using WEKA. WEKA is an open
source consists of different machine learning algorithms for data
mining applications. The algorithms tested are Radial Basis Function
neural network, Support vector machine, and K-Nearest Neighbors
algorithm. Two sets of combined features were utilized for
classification of blood cells images. The first set, exclusively consist
of geometrical features, was used to identify whether the tested blood
cell has a spherical shape or non-spherical cells. While the second
set, consist mainly of textural features was used to recognize the
types of the spherical cells. We have provided an evaluation based on
applying these classification methods to our RBCs image dataset
which were obtained from Serdang Hospital - Malaysia, and
measuring the accuracy of test results. The best achieved
classification rates are 97%, 98%, and 79% for Support vector
machines, Radial Basis Function neural network, and K-Nearest
Neighbors algorithm respectively.
Abstract: We study the anomalous WWγ and WWZ couplings by
calculating total cross sections of two processes at the LHeC with
electron beam energy Ee=140 GeV and the proton beam energy Ep=7
TeV, and at the FCC-ep collider with the polarized electron beam
energy Ee=80 GeV and the proton beam energy Ep=50 TeV. At the
LHeC with electron beam polarization, we obtain the results for the
difference of upper and lower bounds as (0.975, 0.118) and (0.285,
0.009) for the anomalous (Δκγ, λγ) and (Δκz, λz) couplings,
respectively. As for FCC-ep collider, these bounds are obtained as
(1.101, 0.065) and (0.320, 0.002) at an integrated luminosity of
Lint=100 fb^-1.
Abstract: Lead being a toxic heavy metal that mankind is
exposed to the highest levels of this metal from environmental
pollutants. A total of 180 Male scalp hair samples were collected
from different environments in Greater Cairo (GC), i.e. industrial,
heavy traffic and rural areas (60 samples from each) having different
activities during the period of, 1/5/2010 to 1/11/2012. Hair samples
were collected during five stages. Data proved that the concentration
of lead in male industrial areas of Cairo ranged between 6.2847 to
19.0432 μg/g, with mean value of 12.3288 μg/g. On the other hand,
lead content of hair samples of residential-traffic areas ranged
between 2.8634 to 16.3311 μg/g with mean value of 9.7552 μg/g.
While lead concentration on the hair of the male residents living in
rural area ranged between 1.0499-9.0402μg/g with mean value of
4.7327 μg/g. The Pb concentration in scalp hair of Cairo residents of
residential-traffic and rural traffic areas was observed to follow the
same pattern. The pattern was that of decrease concentration of
summer and its increase in winter. Then, there was a marked increase
in Pb concentration of summer 2012, and this increase was
significant. These were obviously seen for the residential-traffic and
rural areas residents. Pb pollution in residents of industrial areas
showed the same seasonal pattern, but there was marked to decrease
in Pb concentration of summer 2012, and this decrease was
significant. Lead pollution in residents of GC was serious. It is worth
noting that the atmosphere is still contaminated by lead despite a
decade of using unleaded gasoline. Strong seasonal variation in
higher Pb concentration on winter than in summer was found. Major
contributions to the pollution with Pb could include industry
emissions, motor vehicle emissions and long transported dust from
outside Cairo. More attention should be paid to the reduction of Pb
content of the urban aerosol and to the Pb pollution health.
Abstract: This paper reports a structured literature review of the
application of Health Information Technology in developing
countries, defined as the World Bank categories Low-income
countries, Lower-middle-income, and Upper-middle-income
countries. The aim was to identify and classify the various
applications of health information technology to assess its current
state in developing countries and explore potential areas of research.
We offer specific analysis and application of HIT in Libya as one of
the developing countries. A structured literature review was
conducted using the following online databases: IEEE, Science
Direct, PubMed, and Google Scholar. Publication dates were set for
2000-2013. For the PubMed search, publications in English, French,
and Arabic were specified. Using a content analysis approach, 159
papers were analyzed and a total number of 26 factors were identified
that affect the adoption of health information technology. Of the 2681
retrieved articles, 159 met the inclusion criteria which were carefully
analyzed and classified. The implementation of health information
technology across developing countries is varied. Whilst it was
initially expected financial constraints would have severely limited
health information technology implementation, some developing
countries like India have nevertheless dominated the literature and
taken the lead in conducting scientific research. Comparing the
number of studies to the number of countries in each category, we
found that Low-income countries and Lower-middle-income had
more studies carried out than Upper-middle-income countries.
However, whilst IT has been used in various sectors of the economy,
the healthcare sector in developing countries is still failing to benefit
fully from the potential advantages that IT can offer.
Abstract: Map is a powerful and convenient tool in helping us to
navigate to different places, but the use of indirect devices often
makes its usage cumbersome. This study intends to propose a new
map navigation dialogue that uses hand gesture. A set of dialogue
was developed from users’ perspective to provide users complete
freedom for panning, zooming, rotate, tilt and find direction
operations. A participatory design experiment was involved here
where one hand gesture and two hand gesture dialogues had been
analysed in the forms of hand gestures to develop a set of usable
dialogues. The major finding was that users prefer one-hand gesture
compared to two-hand gesture in map navigation.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.
Abstract: Due to the importance of ports to trade and economic
development of the regions in which they are inserted, in recent
decades the number of studies devoted to this subject has increased.
Part of these studies considers the ports as business agglomerations
and focuses on port governance. This is an important approach since
the port performance is the result of activities performed by actors
belonging to the port-logistics chain, which need to be properly
coordinated. This coordination takes place through a port governance
model. Given this context, this study aims to analyze the governance
model of the port of Santos from the perspective of port customers.
To do this, a closed-ended questionnaire based on a conceptual model
that considers the key dimensions associated with port governance
was applied to the international freight forwarders that operate in the
port. The results show the applicability of the considered model and
highlight improvement opportunities to be implemented at the port of
Santos.
Abstract: Monocopter is a single-wing rotary flying vehicle
which has the capability of hovering. This flying vehicle includes two
dynamic parts in which more efficiency can be expected rather than
other Micro UAVs due to the extended area of wing compared to its
fuselage. Low cost and simple mechanism in comparison to other
vehicles such as helicopter are the most important specifications of
this flying vehicle.
In the previous paper we discussed the introduction of the final
system but in this paper, the experimental design process of
Monocopter and its control algorithm has been investigated in
general. Also the editorial bugs in the previous article have been
corrected and some translational ambiguities have been resolved.
Initially by constructing several prototypes and carrying out many
flight tests the main design parameters of this air vehicle were
obtained by experimental measurements. Eventually the required
main monocopter for this project was constructed. After construction
of the monocopter in order to design, implementation and testing of
control algorithms first a simple optic system used for determining
the heading angle. After doing numerous tests on Test Stand, the
control algorithm designed and timing of applying control inputs
adjusted. Then other control parameters of system were tuned in
flight tests. Eventually the final control system designed and
implemented using the AHRS sensor and the final operational tests
performed successfully.
Abstract: Animal fats (camel, sheep, goat, rabbit and chicken)
and vegetable oils (corn, sunflower, palm oil and olive oil) were
substituted with different proportions (1, 5, 10 and 20%) of lard.
Fatty acid composition in TG and 2-MG were determined using
lipase hydrolysis and gas chromatography before and after
adulteration. Results indicated that, genuine lard had a high
proportion (60.97%) of the total palmitic acid at 2-MG. However, it
was 8.70%, 16.40%, 11.38%, 10.57%, 29.97 and 8.97% for camel,
beef, sheep, goat, rabbit and chicken, respectively. It could be noticed
also the position-2-MG is mostly occupied by unsaturated fatty acids
among all tested fats except lard. Vegetable oils (corn, sunflower,
palm oil and olive oil) revealed that the levels of palmitic acid
esterifies at 2-MG position was 6.84, 1.43, 9.86 and 1.70%,
respectively. It could be observed also the studied oils had a higher
level of unsaturated fatty acids in the same position, compared with
animal fats under investigation. Moreover, palmitic acid esterifies at
2-MG and PAEF increased gradually as the substituted levels
increased among all tested fat and oil samples. Statistical analysis
showed that the PAEF correlated well with lard level. The detection
of lard in some commercial processed foods (5 French fries, 4 Butter
fats, 5 processed meat and 6 candy samples) was carried out. Results
revealed that 2 samples of French fries and 4 samples of processed
meat contained lard due to their higher PAEF, while butter fat and
candy were free of lard.
Abstract: This paper proposes a backward/forward sweep
method to analyze the power flow in radial distribution systems. The
distribution system has radial structure and high R/X ratios. So the
newton-raphson and fast decoupled methods are failed with
distribution system. The proposed method presents a load flow study
using backward/forward sweep method, which is one of the most
effective methods for the load-flow analysis of the radial distribution
system. By using this method, power losses for each bus branch and
voltage magnitudes for each bus node are determined. This method
has been tested on IEEE 33-bus radial distribution system and
effective results are obtained using MATLAB.
Abstract: Corrosion inhibitors are widely used in concrete
industry to reduce the corrosion rate of steel rebar which is present in
contact with aggressive environments. The present work aims to
using Zamzam water from well located within the Masjid al-Haram
in Mecca, Saudi Arabia 20 m (66 ft) east of the Kaaba, the holiest
place in Islam as corrosion inhibitor for steel in rain water and
simulated acid rain. The effect of Zamzam water was investigated by
electrochemical impedance spectroscopy (EIS) and Potentiodynamic
polarization techniques in Department of Civil Engineering - IUT
Saint-Nazaire, Nantes University, France. Zamzam water is
considered to be one of the most important steel corrosion inhibitor
which is frequently used in different industrial applications. Results
showed that zamzam water gave a very good inhibition for steel
corrosion in rain water and simulated acid rain.
Abstract: The in-cylinder flow and mixture formations are
significant in view of today’s increasing concern on environmental
issues and stringent emission regulations. In this paper, the numerical
simulations of a SI engine at different engine speeds (2000-5000
rpm) at fixed intake flow pressure of 1 bar are studied using the AVL
FIRE software. The simulation results show that when the engine
speed at fixed intake flow pressure is increased, the volumetric
efficiency of the engine decreases. This is due to a richer fuel
conditions near the engine cylinder wall when engine speed is
increased. Significant effects of impingement are also noted on the
upper and side walls of the engine cylinder. These variations in
mixture formation before ignition could affect the thermodynamics
efficiency and specific fuel consumption that would lead to a reduced
engine performance.
Abstract: In this paper, a coupled damage effect in the
instability of a composite rotor is presented, under dynamic loading
response in the harmonic analysis condition. The analysis of the
stress which operates the rotor is done. Calculations of different
energies and the virtual work of the aerodynamic loads from the rotor
blade are developed. The use of the composite material for the rotor
offers a good stability.
Numerical calculations on the model developed prove that the
damage effect has a negative effect on the stability of the rotor.
The study of the composite rotor in transient system allowed
determining the vibratory responses due to various excitations.
Abstract: Soil erosion is a very complex phenomenon, resulting
from detachment and transport of soil particles by erosion agents.
The kinetic energy of raindrop is the energy available for detachment
and transport by splashing rain. The soil erodibility is defined as the
ability of soil to resist to erosion. For this purpose, an experimental
study was conducted in the laboratory using rainfall simulator to
study the effect of the kinetic energy of rain (Ec) on the soil
erodibility (K). The soil used was a sandy agricultural soil of 62.08%
coarse sand, 19.14% fine sand, 6.39% fine silt, 5.18% coarse silt and
7.21% clay. The obtained results show that the kinetic energy of
raindrops evolves as a power law with soil erodibility.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: This paper focuses on the dynamic behavior of
reinforced concrete (RC) slabs. Therefore, the theoretical modal
analysis was performed using two different types of boundary
conditions. Modal analysis method is the most important dynamic
analyses. The analysis would be modal case when there is no external
force on the structure. By using this method in this paper, the effects
of freely and simply supported boundary conditions on the
frequencies and mode shapes of RC square slabs are studied. ANSYS
software was employed to derive the finite element model to
determine the natural frequencies and mode shapes of the slabs.
Then, the obtained results through numerical analysis (finite element
analysis) would be compared with the exact solution. The main goal
of the research study is to predict how the boundary conditions
change the behavior of the slab structures prior to performing
experimental modal analysis. Based on the results, it is concluded
that simply support boundary condition has obvious influence to
increase the natural frequencies and change the shape of the mode
when it is compared with freely supported boundary condition of
slabs. This means that such support conditions have the direct
influence on the dynamic behavior of the slabs. Thus, it is suggested
to use free-free boundary condition in experimental modal analysis to
precisely reflect the properties of the structure. By using free-free
boundary conditions, the influence of poorly defined supports is
interrupted.
Abstract: The present study was conducted to evaluate the
potential applicability of biological trickling filter system for the
treatment of simulated textile wastewater containing reactive azo
dyes with bacterial consortium under non-sterile conditions. The
percentage decolorization for the treatment of wastewater containing
structurally different dyes was found to be higher than 95% in all
trials. The stable bacterial count of the biofilm on stone media of the
trickling filter during the treatment confirmed the presence,
proliferation, dominance and involvement of the added microbial
consortium in the treatment of textile wastewater. Results of
physicochemical parameters revealed the reduction in chemical
oxygen demand (58.5-75.1%), sulphates (18.9-36.5%), and
phosphates (63.6-73.0%). UV-Visible and FTIR spectroscopy
confirmed decolorization of dye containing wastewater was ultimate
consequence of biodegradation. Toxicological studies revealed the
nontoxic nature of degradative metabolites.
Abstract: In oases, the surface water resources are becoming
increasingly scarce and groundwater resources, which generally have
a poor quality due to the high levels of salinity, are often
overexploited. Water saving have therefore become imperative for
better oases sustainability. If drip irrigation is currently recommended
in Morocco for saving water and valuing, its use in the sub-desert
areas does not keep water safe from high evaporation rates. An
alternative to this system would be the use of subsurface drip
irrigation. This technique is defined as an application of water under
the soil surface through drippers, which deliver water at rates
generally similar to surface drip irrigation. As subsurface drip
irrigation is a recently introduced in Morocco, a better understanding
of the infiltration process around a buried source, in local conditions,
and its impact on plant growth is necessarily required. This study
aims to contribute to improving the water use efficiency by testing
the performance of subsurface irrigation system, especially in areas
where water is a limited source. The objectives of this research are
performance evaluation in arid conditions of the subsurface drip
irrigation system for young date palms compared to the surface drip.
In this context, an experimental test is installed at a farmer’s field in
the area of Erfoud (Errachidia Province, southeastern Morocco),
using the subsurface drip irrigation system in comparison with the
classic drip system for young date palms. Flow measurement to
calculate the uniformity of the application of water was done through
two methods: a flow measurement of drippers above the surface and
another one underground. The latter method has also helped us to
estimate losses through evaporation for both irrigation techniques. In
order to compare the effect of two irrigation modes, plants were
identified for each type of irrigation to monitor certain agronomic
parameters (cumulative numbers of palms and roots development).
Experimentation referred to a distribution uniformity of about 88%;
considered acceptable for subsurface drip irrigation while it is around
80% for the surface drip irrigation. The results also show an increase
in root development and in the number of palm, as well as a
substantial water savings due to lower evaporation losses compared
to the classic drip irrigation.
The results of this study showed that subsurface drip irrigation is
an efficient technique, which allows sustainable irrigation in arid
areas.
Abstract: Oases are complex and fragile agro-ecosystems. They
have always existed in environments characterized by an arid climate,
scarcity of rainfall, high temperatures and high evaporation. These
palms have grown up despite the severity of the physical
characteristics thanks to the water's existence and irrigation practice.
The oases are generally spread along non-perennial rivers (wadis),
shallow water table or deep artesian groundwater. However, the
sustainability of oasis system is threatened by water scarcity and
declining of water table levels particularly in arid areas. Located in
the southern east area of Morocco, Tafilalet plain encompasses one of
the largest palm groves in the kingdom. In recent years, this area has
become increasingly threatened by water shortage and has seen a
sharp deterioration under the effect of several combined
anthropogenic and climatic factors. The Bayoud disease, successive
years of drought, Hassan Addakhil dam construction etc are all
factors that have affected both water and phoenicicole heritage of the
area. The objective of this study is to understand the interaction
between qualitative and quantitative degradation of groundwater
resources, and the palm grove dynamics, while reviewing the
assumption that groundwater resources contribute in a direct way to
the conservation of this oasis agroecosystem. A historical analysis
tracing both the oasis dynamics and the groundwater evolution has
been established. Data were collected from satellite images, surveys
with different actors (farmers, Regional Office for Agricultural
Development, Basin agency...). They were complemented by a
synthesis of numerous technical reports in the area. The results
showed that within 40 years, the thickness of the groundwater table
has dropped in 50 %. Along with this, there has been a downsizing of
date palm by 50 %. Areas with higher groundwater level were the
least affected by the downsizing. So we can say that the shallow
groundwater contribute significantly and directly to the water supply
of date palm through its root system, and largely ensures the oasis
ecosystem sustainability.