Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: The world wide web network is a network with a
complex topology, the main properties of which are the distribution
of degrees in power law, A low clustering coefficient and a weak
average distance. Modeling the web as a graph allows locating the
information in little time and consequently offering a help in the
construction of the research engine. Here, we present a model based
on the already existing probabilistic graphs with all the aforesaid
characteristics. This work will consist in studying the web in order to
know its structuring thus it will enable us to modelize it more easily
and propose a possible algorithm for its exploration.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: The main goal of this paper was evaluate the effect of
diets containing different levels of probiotic on performance and milk
composition of lactating cows.
Eight Holstein cows were distributed in two 4x4 Latin square. The
diets were based on corn silage, concentrate and the treatment (0, 3, 6
or 9 grams of probiotic/animal/day). It was evaluated the dry matter
intake of nutrients, milk yield and composition.
The use of probiotics did not affect the nutrient intake (p>0.05)
neither the daily milk production or corrected to 4% fat (p>0.05).
However, it was observed that there was a significant fall in milk
composition with higher levels of probiotics supplementation.
These results emphasize the need of further studies with different
experimental designs or improve the number of Latin square with
longer periods of adaptation.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: This article describes the information system for
measuring and evaluating the dose rate in the environment of nuclear
power plants Mochovce and Bohunice in Slovakia.
The article presents the results achieved in the implementation of
the EU project – Research of monitoring and evaluation of nonstandard
conditions in the area of nuclear power plants. The
objectives included improving the system of acquisition, measuring
and evaluating data with mobile and autonomous units applying new
knowledge from research.
The article provides basic and specific features of the system and
compared to the previous version of the system, also new functions.
Abstract: Fuzzy systems have been successfully used for
exchange rate forecasting. However, fuzzy system is very confusing
and complex to be designed by an expert, as there is a large set of
parameters (fuzzy knowledge base) that must be selected, it is not a
simple task to select the appropriate fuzzy knowledge base for an
exchange rate forecasting. The researchers often look the effect of
fuzzy knowledge base on the performances of fuzzy system
forecasting. This paper proposes a genetic fuzzy predictor to forecast
the future value of daily US Dollar/Euro exchange rate time’s series.
A range of methodologies based on a set of fuzzy predictor’s which
allow the forecasting of the same time series, but with a different
fuzzy partition. Each fuzzy predictor is built from two stages, where
each stage is performed by a real genetic algorithm.
Abstract: Fritillaria oranensis (Liliaceae) was described in 1874
by pomel from Algeria. Plant samples have been collected from the
mount of Tessala (Sidi-Bel-Abbes). The morphological features of
various organs of the plant are described in detail. In the
morphological part of the study, features of various organs of the
plants such as stem and leaf were determined and illustrated.
Ecological studies provide information about the physical and
chemical structure of soil types in Tessala Mountain. The aim of this
original investigation is to put forth ecological and anatomical
features of these species for the first time, but at the same time given
detailed account of the morphological characteristics of the stem and
leaf of Fritillaria oranensis.
Abstract: Natural gas, as one of the most important sources of
energy for many of the industrial and domestic users all over the
world, has a complex, huge supply chain which is in need of heavy
investments in all the phases of exploration, extraction, production,
transportation, storage and distribution. The main purpose of supply
chain is to meet customers’ need efficiently and with minimum cost.
In this study, with the aim of minimizing economic costs, different
levels of natural gas supply chain in the form of a multi-echelon,
multi-period fuzzy linear programming have been modeled. In this
model, different constraints including constraints on demand
satisfaction, capacity, input/output balance and presence/absence of a
path have been defined. The obtained results suggest efficiency of the
recommended model in optimal allocation and reduction of supply
chain costs.
Abstract: FengShui, an old Chinese discipline, dates back to
more than 5000 years, is one of the design principles that aim at
creating habitable and sustainable spaces in harmony with nature by
systematizing data within its own structure. Having emerged from
Chinese mysticism and embodying elements of faith in its principles,
FengShui argues that the positive energy in the environment channels
human behavior and psychology. This argument is supported with the
thesis of quantum physics that ‘everything is made up of energy’ and
gains an important place.
In spaces where living and working take place with several
principles and systematized rules, FengShui promises a happier, more
peaceful and comfortable life by influencing human psychology, acts,
and soul as well as the professional and social life of the individual.
Observing these design properties in houses, workplaces, offices, the
environment, and daily life as a design paradigm is significant. In this
study, how FengShui, a Central Asian culture emanated from Chinese
mysticism, shapes design and how it is used as an element of
sustainable design will be explained.
Abstract: Recently, an increasing number of researchers have
been focusing on working out realistic solutions to sustainability
problems. As sustainability issues gain higher importance for
organisations, the management of such decisions becomes critical.
Knowledge representation is a fundamental issue of complex
knowledge based systems. Many types of sustainability problems
would benefit from models based on experts’ knowledge. Cognitive
maps have been used for analyzing and aiding decision making. A
cognitive map can be made of almost any system or problem. A
fuzzy cognitive map (FCM) can successfully represent knowledge
and human experience, introducing concepts to represent the essential
elements and the cause and effect relationships among the concepts to
model the behaviour of any system. Integrated waste management
systems (IWMS) are complex systems that can be decomposed to
non-related and related subsystems and elements, where many factors
have to be taken into consideration that may be complementary,
contradictory, and competitive; these factors influence each other and
determine the overall decision process of the system. The goal of the
present paper is to construct an efficient IWMS which considers
various factors. The authors’ intention is to propose an expert based
system design approach for implementing expert decision support in
the area of IWMSs and introduces an appropriate methodology for
the development and analysis of group FCM. A framework for such a
methodology consisting of the development and application phases is
presented.
Abstract: Metallic foams have good potential for lightweight
structures for impact and blast mitigation. Therefore it is important to
find out the optimized foam structure (i.e. cell size, shape, relative
density, and distribution) to maximise energy absorption. In this
paper, quasistatic compression and microstructural characterization
of closed-cell aluminium foams of different pore size and cell
distributions have been carried out. We present results for two
different aluminium metal foams of density 0.49-0.51 g/cc and 0.31-
0.34 g/cc respectively that have been tested in quasi-static
compression. The influence of cell geometry and cell topology on
quasistatic compression behaviour has been investigated using optical
microscope and computed tomography (micro-CT) analysis. It is
shown that the deformation is not uniform in the structure and
collapse begins at the weakest point.
Abstract: The parameters of a two-layer soil can be determined by
processing resistivity data obtained from resistivity measurements
carried out on the soil of interest. The processing usually entails
applying the resistivity data as inputs to an optimisation function.
This paper proposes an algorithm which utilises the square error as an
optimisation function. Resistivity data from previous works were
applied to test the accuracy of the new algorithm developed and the
result obtained conforms significantly to results from previous works.
Abstract: Mech-Degla, Degla-Beida and Frezza are the date
(Phoenix dactylifera L.) common varieties with a more or less good
availability and feeble trade value. Some morphologic and
physicochemical factors were determined. Results show that the
whole date weight is significantly different (P= 95%) concerning
Mech-Degla and Degla-Beida which are more commercialized than
Frezza whereas the pulp mass proportion in relation to whole fruits is
highest for Frezza (88.28%). Moreover, there is a large variability
concerning the weights and densities of constitutive tissues in each
variety. The white tissue is dominant in Mech-Degla in opposite to
the two other varieties. The variance analyze showed that the
difference in weights between brown and white tissues is significant
(P = 95%) for all studied varieties. Some other morphologic and
chemical proprieties of the whole pulps and their two constitutive
parts (brown or pigmented and white) are also investigated. The
predominance of phenolics in Mech-Degla (4.01g/100g, w.b) and
Frezza (4.96 g/100g, w.b) pulps brown part is the main result
revealed in this study.
Abstract: This research aims to investigate callus induction,
somatic embryogenesis and indirect plant regeneration of Crassula
ovata (Mill.) Druce – the famous ornamental plant. Experiment no.1:
Callus induction was obtained from leaf and stem explants on
Murashige and Skoog (MS) medium supplemented with various plant
growth regulators (PGRs). Effects of different PGRs, plant
regeneration and subsequent plantlet conversion were also assessed.
Indirect plant regeneration was achieved from the callus of stem
explants by the addition of 1.5 mg/L Kinetin (KN) alone. Best shoot
induction was achieved (6.5 shoots/per explant) after 60 days. For
successful rooting, regenerated plantlets were sub-cultured on the
same MS media supplemented with 1.5 mg/L KN alone. The rooted
plantlets were acclimatized and the survival rate was 90%.
Experiment no.2: Results revealed that 0.5 mg/L 2,4-D alone and in
combination with 1.0 mg/L 6-Benzyladenine (BA) gave 89.8% callus
from the stem explants as compared to leaf explants. Callus
proliferation and somatic embryo formation were also evaluated by
‘Double Staining Method’ and different stages of somatic
embryogenesis were revealed by scanning electron microscope. Full
Strength MS medium produced the highest number (49.6%) of
cotyledonary stage somatic embryos (SEs). Mature cotyledonary
stage SEs developed into plantlets after 12 weeks of culture. Wellrooted
plantlets were successfully acclimatized at the survival rate of
85%. Indirectly regenerated plants did not show any detectable
variation in morphological and growth characteristics when
compared with the donor plant.
Abstract: This paper presents a 4-DOF nonlinear model of a
cracked de Laval rotor-stator system derived based on Energy
Principles. The model has been used to simulate coupled torsionallateral
response of the faulty system with multiple parametric
excitations; rotor-stator-rub, a breathing transverse crack, eccentric
mass and an axial force. Nonlinearity of a “breathing” crack is
incorporated in the model using a simple hinge mechanism suitable
for a shallow crack. Response of the system while passing via its
critical speed with intermittent rotor-stator rub is analyzed. Effects of
eccentricity with phase and acceleration are investigated. Features of
crack, rub and eccentricity in vibration response are explored for
condition monitoring. The presence of a crack and rub are observable
in the power spectrum despite excitations by an axial force and rotor
unbalance. Obtained results are consistent with existing literature and
could be adopted into rotor condition monitoring strategies.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: Communication and effective information exchange
within technology has become a crucial part of delivering knowledge
to students during the learning process. It enables better
understanding, builds trust and respect, and increases the sharing of
knowledge between students. This paper examines the
communication between undergraduate students and their lecturers
during the traditional lecture and when using the Interactive
Electronic Lecture System (IELS). The IELS is an application that
offers a set of components which support the effective
communication between students and their peers and between
students and their lecturers. Moreover, this paper highlights
communication skills such as sender, receiver, channel and feedback.
It will show how the IELS creates a rich communication environment
between its users and how they communicate effectively. To examine
and assess the effectiveness of communication, an experiment was
conducted on groups of users; students and lecturers. The first group
communicated in the traditional lecture while the second group
communicated by means of the IELS application. The results show
that there was more effective communication between the second
group than the first.
Abstract: This study has been presented which is a detailed
work of seismic microzonation of the city center. For seismic
microzonation area of 225 km2 has been selected as the study area.
MASW (Multichannel analysis of surface wave) and seismic
refraction methods have been used to generate one-dimensional shear
wave velocity profile at 250 locations and two-dimensional profile at
60 locations. These shear wave velocities are used to estimate
equivalent shear wave velocity in the study area at every 2 and 5 m
intervals up to a depth of 60 m. Levels of equivalent shear wave
velocity of soil are used the classified of the study area. After the
results of the study, it must be considered as components of urban
planning and building design of Denizli and the application and use
of these results should be required and enforced by municipal
authorities.
Abstract: Recent advances in wireless networking technologies
introduce several energy aware routing protocols in sensor networks.
Such protocols aim to extend the lifetime of network by reducing the
energy consumption of nodes. Many researchers are looking for
certain challenges that are predominant in the grounds of energy
consumption. One such protocol that addresses this energy
consumption issue is ‘Cluster based hierarchical routing protocol’. In
this paper, we intend to discuss some of the major hierarchical
routing protocols adhering towards sensor networks. Furthermore, we
examine and compare several aspects and characteristics of few
widely explored hierarchical clustering protocols, and its operations
in wireless sensor networks (WSN). This paper also presents a
discussion on the future research topics and the challenges of
hierarchical clustering in WSNs.