Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: The effect of Zn2+, Mg2+, and Ba2+ on Saccharomyces
pastorianus performance was evaluated in this study at independent
and three variable combinations. After 96 h of fermentation, high
wort fermentability (%F) = 29.53 was obtained in medium containing
900:4 ppm Mg2+ + Ba2+. Increased ethanol yield 7.35 %(v/v) and
7.13 %(v/v) were obtained in media containing 900:4 ppm Mg2+ +
Ba2+ and 12:900 ppm Zn2+ + Mg2+. Decrease %F = 22.54 and ethanol
yield 6.18 % (v/v) was obtained in medium containing 12:4 ppm Zn2+
+ Ba2+. In media containing the individual ions, increased %F =
27.94 and 26.03 were recorded for media containing 700 ppm Mg2+
and 2 ppm Ba2+ , with ethanol yield of 7.88% (v/v) and 7.62% (v/v)
respectively. Reduced %F and ethanol yield was observed for 10 ppm
Zn2+ and 4 ppm Ba2+ media. The impact of Ba2+ at 1 and 2 ppm was
significant.
Abstract: As the human race will continue to explore the space
by creating new space transportation means and sending them to other
planets, the enhance of atmospheric reentry study is crucial. In this
context, an analysis of mass recession rate of ablative materials for
thermal shields of reentry spacecrafts is important to be carried out.
The paper describes a new estimation method for calculating the mass
recession of an ablator system made of carbon fiber reinforced plastic
materials. This method is based on Arrhenius equation for low
temperatures and, for high temperatures, on a theory applied for the
recession phenomenon of carbon fiber reinforced plastic materials,
theory which takes into account the presence of the resin inside the
materials. The space mission of USERS spacecraft is considered as a
case study.
Abstract: The effect of particle size on shear strength of
granular materials are investigated using direct shear tests. Small
direct shear test (60 mm by 60 mm by 24 mm deep) were conducted
for particles passing the sieves with opening size of 2.36 mm.
Meanwhile, particles passing the standard 20 mm sieves were tested
using large direct shear test (300 mm by 300 mm by 200 mm deep).
The large direct shear tests and the small direct shear tests carried out
using the same shearing rate of 0.09 mm/min and similar normal
stresses of 100, 200 and 300 kPa. The results show that the peak and
residual shear strength increases as particle size increases.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: Historical and ancestral bonds of the countries in the
Middle East have led to similarities in culture and context of their
societies. In addition, economical resources, such as the oil industry,
have generally been an integrative point in the region. Higher
education of a country is influenced by different national and
international factors and, regarding the mentioned bonds, it is inviting
to study the development of the countries of the Middle East in
higher education and draw some practical implications which can be
used in the educational policymaking of the region. This review
includes a data analysis on the population of international students in
the countries of the Middle East. As its second objective, a review
study on the successful countries, that is, those which host the highest
number of international students, and the strategies they have
developed to reach this state among the countries of the region, has
been conducted. Suggestions are made as to the strategies in higher
education systems of these countries which could prove useful and
practical in the development of internationalization of higher
education in the region, specifically with regard to the recruitment of
international students.
Abstract: Rice straw pellets are a promising fuel as a renewable
energy source. Financial analysis is needed to make a utilization
system using rise straw pellets financially feasible, considering all
regional conditions including stakeholders related to the collection and
storage, production, transportation and heat utilization. We conducted
the financial analysis of feasibility for a heat utilization system using
rice straw pellets which has been developed for the first time in
Nanporo, Hokkaido, Japan. Especially, we attempted to clarify the
effect of factors required for the system to be financial feasibility, such
as the heating energy demand and collection and storage method of
rice straw. The financial feasibility was found to improve when
increasing the heating energy demand and collecting wheat straw in
August separately from collection of rice straw in November because
the costs of storing rice straw and producing pellets were reduced.
However, the system remained financially unfeasible. This study
proposed a contractor program funded by a subsidy from Nanporo
local government where a contracted company, instead of farmers,
collects and transports rice straw in order to ensure the financial
feasibility of the system, contributing to job creation in the region.
Abstract: This study focuses on the cooling of a photovoltaic
panel (PV). Indeed, the cooling improves the conversion capacity of
this one and maintains, under extreme conditions of air temperature,
the panel temperature at an appreciable level which avoids the
altering. To do this, a fan provides forced circulation of air. Because
the fan is supplied by the panel, it is necessary to determine the
optimum operating point that unites efficiency of the PV with the
consumption of the fan. For this matter, numerical simulations are
performed at varying mass flow rates of air, under two extreme air
temperatures (50°C, 25°C) and a fixed solar radiation (1000W.m2) in
a case of no wind.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.
Abstract: A total of 150 meat type chickens comprising 50 each
of Arbor Acre, Marshall and Ross were used for this study which
lasted for 10 weeks at the Federal University of Agriculture,
Abeokuta, Nigeria. Growth performance data were collected from the
third week through week 10 and data obtained were analysed using
the Generalized Linear Model Procedure. Heritability estimates (h2)
for body dimensions carried out on the chicken strains ranged from
low to high. Marshall broiler chicken strain had the highest h2 for
body weight 0.46±0.04, followed by Arbor Acre and Ross with h2
being 0.38±0.12 and 0.26±0.06, respectively. The repeatability
estimates for body weight in the three broiler strains were high, and it
ranged from 0.70 at week 4 to 0.88 at week 10. Relationships
between the body weight and linear body measurements in the broiler
chicken strains were positive and highly significant (p > 0.05).
Abstract: Malathion (ML) is a well known pesticide commonly
used in many agricultural and non-agricultural processes. Its toxicity
has been attributed primarily to the accumulation of acetylcholine
(Ach) at nerve junctions, due to the inhibition of acetylcholinesterase
(AChE). The aim of the current research was to study the protective
effect of the melissa plant extract against reproductive impairment
induced by malathion in 32 male albino rats, and the biological
experiment was divided into four groups (8 in each) that given
malathion (27 mg/kg; 1/50 of the LD50 for an oral dose) and/or
Melissa officinalis (MO) extract (200mg/kg/day) by gavages
technique. The sperm counts, sperm motility, sperm morphology,
FSH, LH, and testosterone levels had been determined in testes
homogenate at the end of the experiment. It is worthy to report that,
rats treated with melissa extract did not show a significant difference
when compared with the control group, while rats given malathion
alone had significantly lower sperm count, sperm motility, and
significantly higher abnormal sperm numbers, than the untreated
control rats as well as having significantly lower serum FSH, LH, and
testosterone levels compared with the control group. Administrations
of melissa extract restore all mentioned histological parameters
towards the control group and the melissa extract had a strong
positive protective effect against malathion toxicity. Results the of
biological parameters were confirmed by the histological
examination of rat testes and indicated that, both control and melissa
groups showing normal seminiferous tubules, while malathion group
testicular tissues had necrosis, edema in the seminiferous tubules and
degeneration of spermatogonial cells lining the seminiferous tubules
with incomplete spermatogenesis. The use of melissa against
malathion improved the histological picture and showing normal
seminiferous tubules with complete spermatogenesis and almost there
was no histopathological changes could be noted.
Abstract: Pomegranate (Punica granatum L.) is an ancient fruit of great medical interest and rich source of antioxidants. Pesticides as dimethoate play a crucial role in the occurrence many diseases in plants, animal and human. Therefore the ability of Pomegranate (Punica granatum L.) to alleviate hepatotoxicity induced by organophosphate pesticide dimethoate was investigated. Albino male rats were divided randomly into 4 groups and kept at 7 animals per group in an environmentally controlled condition for 6 weeks. The first group was served as a control group (basal diet), the second group fed on basal diet supplemented with 5% freeze dried pomegranate seeds, the third group fed on 20 ppm dimethoate contaminated diet and the last group fed on dimethoate contaminated diet supplemented with 5% freeze dried pomegranate seeds. The results revealed that administration of dimethoate caused high significant increased in liver functions: alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP) activities as well as lipid peroxide (malonaldhyde, MDA); on the other hand high significant decreased on glutathione (GSH), glutathione peroxidase (GPx), albumin and total protein were observed. However addition of 5% freeze dried pomegranate seeds significantly improved all previously mentioned parameters. These results indicate the dimethoate induced hepatotoxicity and highlight the protective effect of pomegranate seeds as a potential protective agent against dimethoate induced hepatotoxicity. This may be attributed to the powerful antioxidants (polyphenols, total phenols, and total flavonoids) which present in high levels in pomegranate as well as improving the immunity by activation of antioxidant enzymes GSH and GPx.
Abstract: This research paper aims to identify, analyze and rank
factors affecting labor productivity in Spain with respect to their
relative importance. Using a selected set of 35 factors, a structured
questionnaire survey was utilized as the method to collect data from
companies. Target population is comprised by a random
representative sample of practitioners related with the Spanish
construction industry. Findings reveal the top five ranked factors are
as follows: (1) shortage or late supply of materials; (2) clarity of the
drawings and project documents; (3) clear and daily task assignment;
(4) tools or equipment shortages; (5) level of skill and experience of
laborers. Additionally, this research also pretends to provide simple
and comprehensive recommendations so that they could be
implemented by construction managers for an effective management
of construction labor forces.
Abstract: The most important part of modern lean low NOx combustors is a premixer where swirlers are often used for intensification of mixing processes and further formation of required flow pattern in combustor liner. Swirling flow leads to formation of complex eddy structures causing flow perturbations. It is able to cause combustion instability. Therefore, at design phase, it is necessary to pay great attention to aerodynamics of premixers. Analysis based on unsteady CFD modeling of swirling flow in production combustor swirler showed presence of large number of different eddy structures that can be conditionally divided into three types relative to its location of origin and a propagation path. Further, features of each eddy type were subsequently defined. Comparison of calculated and experimental pressure fluctuations spectrums verified correctness of computations.