Abstract: Design concepts of real-time embedded system can be
realized initially by introducing novel design approaches. In this
literature, model based design approach and in-the-loop testing were
employed early in the conceptual and preliminary phase to formulate
design requirements and perform quick real-time verification. The
design and analysis methodology includes simulation analysis, model
based testing, and in-the-loop testing. The design of conceptual driveby-
wire, or DBW, algorithm for electronic control unit, or ECU, was
presented to demonstrate the conceptual design process, analysis, and
functionality evaluation. The concepts of DBW ECU function can be
implemented in the vehicle system to improve electric vehicle, or EV,
conversion drivability. However, within a new development process,
conceptual ECU functions and parameters are needed to be evaluated.
As a result, the testing system was employed to support conceptual
DBW ECU functions evaluation. For the current setup, the system
components were consisted of actual DBW ECU hardware, electric
vehicle models, and control area network or CAN protocol. The
vehicle models and CAN bus interface were both implemented as
real-time applications where ECU and CAN protocol functionality
were verified according to the design requirements. The proposed
system could potentially benefit in performing rapid real-time
analysis of design parameters for conceptual system or software
algorithm development.
Abstract: This study investigates the use of a time-series of
MODIS NDVI data to identify agricultural land cover change on an
annual time step (2007 - 2012) and characterize the trend. Following
an ISODATA classification of the MODIS imagery to selectively
mask areas not agriculture or semi-natural, NDVI signatures were
created to identify areas cereals and vineyards with the aid of
ancillary, pictometry and field sample data for 2010. The NDVI
signature curve and training samples were used to create a decision
tree model in WEKA 3.6.9 using decision tree classifier (J48)
algorithm; Model 1 including ISODATA classification and Model 2
not. These two models were then used to classify all data for the
study area for 2010, producing land cover maps with classification
accuracies of 77% and 80% for Model 1 and 2 respectively. Model 2
was subsequently used to create land cover classification and change
detection maps for all other years. Subtle changes and areas of
consistency (unchanged) were observed in the agricultural classes
and crop practices. Over the years as predicted by the land cover
classification. Forty one percent of the catchment comprised of
cereals with 35% possibly following a crop rotation system.
Vineyards largely remained constant with only one percent
conversion to vineyard from other land cover classes.
Abstract: Corrosion of concrete sewer pipes induced by
sulphuric acid attack is a recognised problem worldwide, which is not
only an attribute of countries with hot climate conditions as thought
before. The significance of this problem is by far only realised when
the pipe collapses causing surface flooding and other severe
consequences. To change the existing post-reactive attitude of
managing companies, easy to use and robust models are required to
be developed which currently lack reliable data to be correctly
calibrated. This paper focuses on laboratory experiments of
establishing concrete pipe corrosion rate by submerging samples in to
0.5pH sulphuric acid solution for 56 days under 10ºC, 20ºC and 30ºC
temperature regimes. The result showed that at very early stage of the
corrosion process the samples gained overall mass, at 30ºC the
corrosion progressed quicker than for other temperature regimes,
however with time the corrosion level for 10ºC and 20ºC regimes
tended towards those at 30ºC. Overall, at these conditions the
corrosion rates of 10 mm/year, 13,5 mm/year and 17 mm/year were
observed.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: In this paper, an analytical simplified method for
calculating elasto-plastic stresses strains of notched bodies subject to
non-proportional loading paths is discussed. The method was based
on the Neuber notch correction, which relates the incremental elastic
and elastic-plastic strain energy densities at the notch root and the
material constitutive relationship. The validity of the method was
presented by comparing computed results of the proposed model
against finite element numerical data of notched shaft. The
comparison showed that the model estimated notch-root elasto-plastic
stresses strains with good accuracy using linear-elastic stresses. The
prosed model provides more efficient and simple analysis method
preferable to expensive experimental component tests and more
complex and time consuming incremental non-linear FE analysis.
The model is particularly suitable to perform fatigue life and fatigue
damage estimates of notched components subjected to nonproportional
loading paths.
Abstract: Due to rapid pressured of population growth, city has
started to lose its old tradition. City becomes congested with
uncomfortably living. Urban renewal refers orderly development of
settlements as well as land redevelopment. For this paper Chittagong
city has been selected as study area. It had a great tradition but it has
been losing its concord. Land use pattern of this place is also
haphazard due to lack of planning intervention. Renewal plan is
needed to ascertain suitable redevelopment and to recommend on
preservation of city heritage structure. The goal of this study is to
prepare a renewal plan using local planning approach. Social impact
methods have been used to achieve this goal. Both primary and
secondary data are used to achieve the goal. This study may find out
a complete solution for healthy living in old Part of city. This study
will help to preserve its tradition and makes urban lives more livable.
Abstract: This paper shows in detail the mathematical model of
direct and inverse kinematics for a robot manipulator (welding type)
with four degrees of freedom. Using the D-H parameters, screw
theory, numerical, geometric and interpolation methods, the
theoretical and practical values of the position of robot were
determined using an optimized algorithm for inverse kinematics
obtaining the values of the particular joints in order to determine the
virtual paths in a relatively short time.
Abstract: Present paper describes method of obtaining clay
ceramic foam (CCF) and foam concrete (FC), by direct foaming with
high speed mixer-disperser (HSMD). Three foaming agents (FA) are
compared for the FC and CCF production: SCHÄUMUNGSMITTEL
W 53 FLÜSSIG (Zschimmer & Schwarz Gmbh, Germany), SCF-
1245 (Sika, test sample, Latvia) and FAB-12 (Elade, Latvija). CCF
were obtained at 950, 1000°C, 1150°C and 1150°C firing temperature
and have mechanical compressive strength 1.2, 2.55 and 4.3 MPa and
porosity 79.4, 75.1, 71.6%, respectively. Obtained FC has 6-14 MPa
compressive strength and porosity 44-55%. The goal of this work
was development of a sustainable and durable ceramic cellular
structures using HSMD.
Abstract: This paper is part of a study to develop robots for
farming. As such power requirement to operate equipment attach to
such robots become an important factor. Soil-tool interaction plays
major role in power consumption, thus predicting accurately the
forces which act on the blade during the farming is very important for
optimal designing of farm equipment. In this paper, a finite element
investigation for tillage tools and soil interaction is described by
using an inelastic constitutive material law for agriculture
application. A 3-dimensional (3D) nonlinear finite element analysis
(FEA) is developed to examine behavior of a blade with different
rake angles moving in a block of soil, and to estimate the blade force.
The soil model considered is an elastic-plastic with non-associated
Drucker-Prager material model. Special use of contact elements are
employed to consider connection between soil-blade and soil-soil
surfaces. The FEA results are compared with experimental ones,
which show good agreement in accurately predicting draft forces
developed on the blade when it moves through the soil. Also a very
good correlation was obtained between FEA results and analytical
results from classical soil mechanics theories for straight blades.
These comparisons verified the FEA model developed. For analyzing
complicated soil-tool interactions and for optimum design of blades,
this method will be useful.
Abstract: One of the crucial parameters of digital cryptographic
systems is the selection of the keys used and their distribution. The
randomness of the keys has a strong impact on the system’s security
strength being difficult to be predicted, guessed, reproduced, or
discovered by a cryptanalyst. Therefore, adequate key randomness
generation is still sought for the benefit of stronger cryptosystems.
This paper suggests an algorithm designed to generate and test
pseudo random number sequences intended for cryptographic
applications. This algorithm is based on mathematically manipulating
a publically agreed upon information between sender and receiver
over a public channel. This information is used as a seed for
performing some mathematical functions in order to generate a
sequence of pseudorandom numbers that will be used for
encryption/decryption purposes. This manipulation involves
permutations and substitutions that fulfill Shannon’s principle of
“confusion and diffusion”. ASCII code characters were utilized in the
generation process instead of using bit strings initially, which adds
more flexibility in testing different seed values. Finally, the obtained
results would indicate sound difficulty of guessing keys by attackers.
Abstract: Transmission shafts are affected by various forces, for
example, during acceleration or sudden breaks, bending during
transportation, vertical forces that lead to cuts. One of the main
failures in combines is breaking shaft which repairmen refer it.
Structural resistance of canal against torque is very important in the
beginning of the movement. For analyzing stress, a typical sample
from a type of combine was selected, called JD955 combine. Long
shaft in this combine was analyzed with finite element method by
Ansys13 generic package under static load. Conducted analysis
showed that there is a maximum stress in contact surfaces of
indentations and also in place of changing diameter. Safety factor
value is low in parts of the shaft and this increases the probability of
failure at these points. To improve the conditions with the least cost
and an approach of product improvement, using alternative alloy is
important.
Abstract: PhilSHORE is a multi-site, multi-device and multicriteria
decision support tool designed to support the development of
tidal current energy in the Philippines. Its platform is based on
Geographic Information Systems (GIS) which allows for the
collection, storage, processing, analyses and display of geospatial
data. Combining GIS tools with open source web development
applications, PhilSHORE becomes a webGIS-based marine spatial
planning tool. To date, PhilSHORE displays output maps and graphs
of power and energy density, site suitability and site-device analysis.
It enables stakeholders and the public easy access to the results of
tidal current energy resource assessments and site suitability
analyses. Results of the initial development show that PhilSHORE is
a promising decision support tool for ORE project developments.
Abstract: Coal is an important non-renewable energy source of
and can be associated with radioactive elements. In Figueira city,
Paraná state, Brazil, it was recorded high uranium activity near the
coal mine that supplies a local thermoelectric power plant. In this
context, the radon activity (Rn-222, produced by the Ra-226 decay in
the U-238 natural series) was evaluated in groundwater, river water
and effluents produced from the acid mine drainage in the coal reject
dumps. The samples were collected in August 2013 and in February
2014 and analyzed at LABIDRO (Laboratory of Isotope and
Hydrochemistry), UNESP, Rio Claro city, Brazil, using an alpha
spectrometer (AlphaGuard) adjusted to evaluate the mean radon
activity concentration in five cycles of 10 minutes. No radon activity
concentration above 100 Bq.L-1, which was a previous critic value
established by the World Health Organization. The average radon
activity concentration in groundwater was higher than in surface
water and in effluent samples, possibly due to the accumulation of
uranium and radium in the aquifer layers that favors the radon
trapping. The lower value in the river waters can indicate dilution and
the intermediate value in the effluents may indicate radon absorption
in the coal particles of the reject dumps. The results also indicate that
the radon activities in the effluents increase with the sample
acidification, possibly due to the higher radium leaching and the
subsequent radon transport to the drainage flow. The water samples
of Laranjinha River and Ribeirão das Pedras stream, which,
respectively, supply Figueira city and receive the mining effluent,
exhibited higher pH values upstream the mine, reflecting the acid
mine drainage discharge. The radionuclides transport indicates the
importance of monitoring their activity concentration in natural
waters due to the risks that the radioactivity can represent to human
health.
Abstract: The emerging markets of post-USSR countries have
attracted Western multinational companies; however, weak
institutions and unstable host country environments have hindered the
implementation of successful management practices. The Ukrainian
market, in light of recent events, is particularly interesting to study
for its compatibility with Western businesses. This paper focuses on
factors that can facilitate or inhibit the transfer of human resource
management practices from Western headquarters to Ukrainian
subsidiaries. To explain the national context’s effects better, a
business systems approach has been applied to a qualitative study of
16 wholly owned Western subsidiaries, dissecting the reasons for a
weak integration of Western practices in Ukraine. Results show that
underdeveloped institutions have forced companies to develop
additional practices that compensate for national weaknesses, as well
as to adjust to a constantly changing environment. Flexibility and
local responsiveness were observed as vital for success in Ukraine.
Abstract: Transmission system performance analysis is vital to
proper planning and operations of power systems in the presence of
deregulation. Key performance indicators (KPIs) are often used as
measure of degree of performance. This paper gives a novel method
to determine the transmission efficiency by evaluating the ratio of
real power losses incurred from a specified transfer direction.
Available Transmission Transfer Efficiency (ATTE) expresses the
percentage of real power received resulting from inter-area available
power transfer. The Tie line (Rated system path) performance is seen
to differ from system wide (Network response) performance and
ATTE values obtained are transfer direction specific. The required
sending end quantities with specified receiving end ATC and the
receiving end power circle diagram are obtained for the tie line
analysis. The amount of real power loss load relative to the available
transfer capability gives a measure of the transmission grid
efficiency.
Abstract: We report the microstructural and magnetic properties
of Ni50Mn39Sn11 and Ni50Mn36Sn14 ribbon Heusler alloys.
Experimental results were obtained by differential scanning
calorymetry, X-ray diffraction and vibrating sample magnetometry
techniques. The Ni-Mn-Sn system undergoes a martensitic structural
transformation in a wide temperature range. For example, for
Ni50Mn39Sn11 the start and finish temperatures of the martensitic and
austenite phase transformation for ribbon alloy were Ms=336K,
Mf=328K, As=335K and Af=343K whereas no structural
transformation is observed for Ni50Mn36Sn14 alloys. Magnetic
measurements show the typical ferromagnetic behavior with Curie
temperature 207 K at low applied field of 50 Oe. The complex
behavior exhibited by these Heusler alloys should be ascribed to the
strong coupling between magnetism and structure, being their
magnetic behavior determined by the distance between Mn atoms.
Abstract: This study was carried out to investigate the adverse
effect of industrial wastewater on surface water quality in Gebeng
industrial estate, Pahang, Malaysia. Surface water was collected from
six sampling stations. Physicochemical parameters were
characterized based on in-situ and ex-situ analysis according to
standard methods by American Public Health Association (APHA).
Selected heavy metals were determined by using Inductively Coupled
Plasma Mass Spectrometry (ICP MS). The results revealed that the
concentration of heavy metals such as Pb, Cu, Cd, Cr and Hg were
high in samples. The results also showed that the value of Pb and Hg
were higher in the wet season in comparison to dry season.
According to Malaysia National Water Quality Standard (NWQS)
and Water Quality Index (WQI) all the sampling station were
categorized as class IV (highly polluted). The present study revealed
that the adverse effects of careless disposal of wastes and directly
discharge of effluents affected on surface water quality. Therefore,
the authorities should implement the laws to ensure the proper
practices of wastewater management for environmental sustainability
around the study area.
Abstract: Association rule mining is one of the most important fields of data mining and knowledge discovery. In this paper, we propose an efficient multiple support frequent pattern growth algorithm which we called “MSFP-growth” that enhancing the FPgrowth algorithm by making infrequent child node pruning step with multiple minimum support using maximum constrains. The algorithm is implemented, and it is compared with other common algorithms: Apriori-multiple minimum supports using maximum constraints and FP-growth. The experimental results show that the rule mining from the proposed algorithm are interesting and our algorithm achieved better performance than other algorithms without scarifying the accuracy.
Abstract: Steel tubular towers serving as support structures for large wind turbines are subjected to several hundred million stress cycles caused by the turbulent nature of the wind. This causes highcycle fatigue, which could govern the design of the tower. Maintaining the support structure after the wind turbines reach its typical 20-year design life has become a common practice; however, quantifying the changes in the reliability on the tower is not usual. In this paper the effect of fatigue damage in the wind turbine structure is studied whit the use of fracture mechanics, and a method to estimate the reliability over time of the structure is proposed. A representative wind turbine located in Oaxaca, Mexico is then studied. It is found that the system reliability is significantly affected by the accumulation of fatigue damage.
Abstract: The use of energy dissipation systems for seismic applications has increased worldwide, thus it is necessary to develop practical and modern criteria for their optimal design. Here, a direct displacement-based seismic design approach for frame buildings with hysteretic energy dissipation systems (HEDS) is applied. The building is constituted by two individual structural systems consisting of: 1) a main elastic structural frame designed for service loads; and 2) a secondary system, corresponding to the HEDS, that controls the effects of lateral loads. The procedure implies to control two design parameters: a) the stiffness ratio (α=Kframe/Ktotal system), and b) the strength ratio (γ=Vdamper/Vtotal system). The proposed damage-controlled approach contributes to the design of a more sustainable and resilient building because the structural damage is concentrated on the HEDS. The reduction of the design displacement spectrum is done by means of a damping factor (recently published) for elastic structural systems with HEDS, located in Mexico City. Two limit states are verified: serviceability and near collapse. Instead of the traditional trial-error approach, a procedure that allows the designer to establish the preliminary sizes of the structural elements of both systems is proposed. The design methodology is applied to an 8-story steel building with buckling restrained braces, located in soft soil of Mexico City. With the aim of choosing the optimal design parameters, a parametric study is developed considering different values of હ and . The simplified methodology is for preliminary sizing, design, and evaluation of the effectiveness of HEDS, and it constitutes a modern and practical tool that enables the structural designer to select the best design parameters.