Abstract: The ionizing radiations cause different kinds of damages in electronic components. MOSFETs, most common transistors in today’s digital and analog circuits, are severely sensitive to TID damage. In this work, the threshold voltage shift of CD4007 device, which is an integrated circuit including P-channel and N-channel MOS transistors, was investigated for low dose gamma irradiation under different gate bias voltages. We used linear extrapolation method to extract threshold voltage from ID-VG characteristic curve. The results showed that the threshold voltage shift was approximately 27.5 mV/Gy for N-channel and 3.5 mV/Gy for P-channel transistors at the gate bias of |9 V| after irradiation by Co-60 gamma ray source. Although the sensitivity of the devices under test were strongly dependent to biasing condition and transistor type, the threshold voltage shifted linearly versus accumulated dose in all cases. The overall results show that the application of CD4007 as an electronic buffer in a radiation therapy system is limited by TID damage. However, this integrated circuit can be used as a cheap and sensitive radiation dosimeter for accumulated dose measurement in radiation therapy systems.
Abstract: Transmission shafts are affected by various forces, for
example, during acceleration or sudden breaks, bending during
transportation, vertical forces that lead to cuts. One of the main
failures in combines is breaking shaft which repairmen refer it.
Structural resistance of canal against torque is very important in the
beginning of the movement. For analyzing stress, a typical sample
from a type of combine was selected, called JD955 combine. Long
shaft in this combine was analyzed with finite element method by
Ansys13 generic package under static load. Conducted analysis
showed that there is a maximum stress in contact surfaces of
indentations and also in place of changing diameter. Safety factor
value is low in parts of the shaft and this increases the probability of
failure at these points. To improve the conditions with the least cost
and an approach of product improvement, using alternative alloy is
important.
Abstract: In this research, performance of rotavator with horizontal rotary axis and vertical rotary axis has been evaluated and compared. The mean weight diameter (MWD), cross-sectional area disturbed and cone index of soil investigated. Factorial experiments based on a randomized complete block with 18 treatments, three different velocities 2.2, 3.5, 6.1 km/h; three different depth of 5, 10, 15cm and with two rotary plows horizontal axis and vertical axis with three replications were used. Result showed that maximum MWD in 6.1 km/h and 15cm of depth were 55.6 and 52.5mm for horizontal axis rotavator, respectively. The minimum MWD in 2.2 km/h and 5cm of depth for vertical axis rotavator were 34.9 and 35.1mm, respectively. The values of cone index 1861.1 and 2339.5 kPa for vertical axis rotavator and horizontal axis rotavator were obtained, respectively, also the values of cross-sectional area disturbed 687 and 497.2cm2 for vertical axis rotavator and horizontal axis rotavator were obtained, respectively.
Abstract: Deep Brain Stimulation or DBS is a surgical treatment for Parkinson-s Disease with three stimulation parameters: frequency, pulse width, and voltage. The parameters should be selected appropriately to achieve effective treatment. This selection now, performs clinically. The aim of this research is to study chaotic behavior of recorded tremor of patients under DBS in order to present a computational method to recognize stimulation optimum voltage. We obtained some chaotic features of tremor signal, and discovered embedding space of it has an attractor, and its largest Lyapunov exponent is positive, which show tremor signal has chaotic behavior, also we found out, in optimal voltage, entropy and embedding space variance of tremor signal have minimum values in comparison with other voltages. These differences can help neurologists recognize optimal voltage numerically, which leads to reduce patients' role and discomfort in optimizing stimulation parameters and to do treatment with high accuracy.
Abstract: To study the effect of suitable methods for
propagation of True Potato Seed (TPS) progenies, transplant and
selection of the best progenies, a factorial experiment base on a
randomized complete block design was carried out in the research
field of Sahneh region, Kermanshah, Iran during 2009-2010. Five
selective progenies from CIP (International Potato Center) including
CIP.994013, CIP.994002, CIP.994014, CIP.888006, and
CIP.994001 and two transplant preparation methods (Paper pot
preparation for mechanical cultivation and preparation in transplant
trays for manual cultivation) were studied in three replications.
Results showed that different progenies had no significant effect on
plant height (cm) and tuber yield (t ha-1), whereas had a significant
effect on number of tubers per unit area (m2). There was significant
difference between transplant preparation methods for plant height
and tuber yield. The interaction effect of progenies and transplant
preparation method was not significant for these traits. CIP.888006
progeny and paper pot preparation method produced the highest
tuber yields. Also CIP.994002 and CIP.994014 progenies considered
as the best progenies under paper pot preparation method due to high
yields.
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.