Abstract: In oases, the surface water resources are becoming
increasingly scarce and groundwater resources, which generally have
a poor quality due to the high levels of salinity, are often
overexploited. Water saving have therefore become imperative for
better oases sustainability. If drip irrigation is currently recommended
in Morocco for saving water and valuing, its use in the sub-desert
areas does not keep water safe from high evaporation rates. An
alternative to this system would be the use of subsurface drip
irrigation. This technique is defined as an application of water under
the soil surface through drippers, which deliver water at rates
generally similar to surface drip irrigation. As subsurface drip
irrigation is a recently introduced in Morocco, a better understanding
of the infiltration process around a buried source, in local conditions,
and its impact on plant growth is necessarily required. This study
aims to contribute to improving the water use efficiency by testing
the performance of subsurface irrigation system, especially in areas
where water is a limited source. The objectives of this research are
performance evaluation in arid conditions of the subsurface drip
irrigation system for young date palms compared to the surface drip.
In this context, an experimental test is installed at a farmer’s field in
the area of Erfoud (Errachidia Province, southeastern Morocco),
using the subsurface drip irrigation system in comparison with the
classic drip system for young date palms. Flow measurement to
calculate the uniformity of the application of water was done through
two methods: a flow measurement of drippers above the surface and
another one underground. The latter method has also helped us to
estimate losses through evaporation for both irrigation techniques. In
order to compare the effect of two irrigation modes, plants were
identified for each type of irrigation to monitor certain agronomic
parameters (cumulative numbers of palms and roots development).
Experimentation referred to a distribution uniformity of about 88%;
considered acceptable for subsurface drip irrigation while it is around
80% for the surface drip irrigation. The results also show an increase
in root development and in the number of palm, as well as a
substantial water savings due to lower evaporation losses compared
to the classic drip irrigation.
The results of this study showed that subsurface drip irrigation is
an efficient technique, which allows sustainable irrigation in arid
areas.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Chloride resistance in Ultra High Performance
Concrete (UHPC) is determined in this paper. This work deals with
the one dimension chloride transport, which can be potentially
dangerous particularly for the durability of concrete structures. Risk
of reinforcement corrosion due to exposure to the concrete surface to
direct the action of chloride ions (mainly in the form de-icing salts or
groundwater) is dangerously increases. The measured data are
investigated depending on the depth of penetration of chloride ions
into the concrete structure. Comparative measurements with normal
strength concrete are done as well. The experimental results showed
that UHCP have improved resistance of chlorides penetration than
NSC and also chloride diffusion depth is significantly lower in
UHCP.
Abstract: Qatar’s primary source of fresh water is through
seawater desalination. Amongst the major processes that are
commercially available on the market, the most common large scale
techniques are Multi-Stage Flash distillation (MSF), Multi Effect
distillation (MED), and Reverse Osmosis (RO). Although commonly
used, these three processes are highly expensive down to high energy
input requirements and high operating costs allied with maintenance
and stress induced on the systems in harsh alkaline media. Beside that
cost, environmental footprint of these desalination techniques are
significant; from damaging marine eco-system, to huge land use, to
discharge of tons of GHG and huge carbon footprint.
Other less energy consuming techniques based on membrane
separation are being sought to reduce both the carbon footprint and
operating costs is membrane distillation (MD).
Emerged in 1960s, MD is an alternative technology for water
desalination attracting more attention since 1980s. MD process
involves the evaporation of a hot feed, typically below boiling point
of brine at standard conditions, by creating a water vapor pressure
difference across the porous, hydrophobic membrane. Main
advantages of MD compared to other commercially available
technologies (MSF and MED) and specially RO are reduction of
membrane and module stress due to absence of trans-membrane
pressure, less impact of contaminant fouling on distillate due to
transfer of only water vapor, utilization of low grade or waste heat
from oil and gas industries to heat up the feed up to required
temperature difference across the membrane, superior water quality,
and relatively lower capital and operating cost.
To achieve the objective of this study, state of the art flat-sheet
cross-flow DCMD bench scale unit was designed, commissioned, and
tested. The objective of this study is to analyze the characteristics and
morphology of the membrane suitable for DCMD through SEM
imaging and contact angle measurement and to study the water
quality of distillate produced by DCMD bench scale unit.
Comparison with available literature data is undertaken where
appropriate and laboratory data is used to compare a DCMD distillate
quality with that of other desalination techniques and standards.
Membrane SEM analysis showed that the PTFE membrane used
for the study has contact angle of 127º with highly porous surface
supported with less porous and bigger pore size PP membrane. Study
on the effect of feed solution (salinity) and temperature on water
quality of distillate produced from ICP and IC analysis showed that
with any salinity and different feed temperature (up to 70ºC) the
electric conductivity of distillate is less than 5 μS/cm with 99.99%
salt rejection and proved to be feasible and effective process capable
of consistently producing high quality distillate from very high feed
salinity solution (i.e. 100000 mg/L TDS) even with substantial
quality difference compared to other desalination methods such as
RO and MSF.
Abstract: The MIGR’HYCAR research project was initiated to provide decisional tools for risks connected to oil spill drifts in continental waters. These tools aim to serve in the decision-making process once oil spill pollution occurs and/or as reference tools to study scenarios of potential impacts of pollutions on a given site. This paper focuses on the study of the distribution of polycyclic aromatic hydrocarbons (PAHs) and derivatives from oil spill in water as function of environmental parameters. Eight petroleum oils covering a representative range of commercially available products were tested. 41 polycyclic aromatic hydrocarbons (PAHs) and derivates, among them 16 EPA priority pollutants were studied by dynamic tests at laboratory scale. The chemical profile of the water soluble fraction was different from the parent oil profile due to the various water solubility of oil components. Semi-volatile compounds (naphtalenes) constitute the major part of the water soluble fraction. A large variation in composition of the water soluble fraction was highlighted depending on oil type. Moreover, four environmental parameters (temperature, suspended solid quantity, salinity and oil: water surface ratio) were investigated with the Taguchi experimental design methodology. The results showed that oils are divided into three groups: the solubility of Domestic fuel and Jet A1 presented a high sensitivity to parameters studied, meaning they must be taken into account. For Gasoline (SP95-E10) and Diesel fuel, a medium sensitivity to parameters was observed. In fact, the four others oils have shown low sensitivity to parameters studied. Finally, three parameters were found to be significant towards the water soluble fraction.
Abstract: The effect of exogenous application; seed priming or foliar spraying of salicylic acid (SA) on Yecora Rojo and Paragon wheat cv. under NaCl-salinity. Gas exchange parameters, growth parameters, yield and yield components were reduced in both cultivars under salinity stress with foliar spray and soaking seeds. Exogenous application of SA through foliar spraying or seed soaking showed a slight increases or decreases with the application method or between cultivars. SA foliar spraying exhibited a slight improvement over SA seed soaking in most parameters, particularly in Paragon. Although, seed soaking was less effective than foliar spraying, it was a slightly better with Yecora Rojo in some parameters. However, the low SA concentration; 0.5mM tended to improve most parameters in both cultivars. From data of the experiment, it has been concluded that the effect of SA depends on cultivar genotype and SA concentration.
Abstract: Germination and seedling responses of seven safflower seed genotypes (Dinçer, Remzibey, Black Sun2 cultivars and A19, F4, I1, J19 lines) to different salinity concentrations (0, 5, 10 and 20g l-1) and temperatures (10 and 20oC) evaluated in Completely Randomized Factorial Designs in Department of Field Crops of Selcuk University, Konya, Turkey. Seeds in the control (distilled water) had at 10 and 20oC the highest germination percentage (93.88 and 94.32%), shoot length (4.60 and 8.72cm) and root length (4.27 and 6.54cm) shoot dry weight (22.37mg and 25.99mg) and root dry weight (2.22 and 2.47mg). As the salt concentration increased, values of all characters were decreased. In this experiment, in 20g l-1 salt concentration found germination percentage (21.28 and 26.66%), shoot (1.32 and 1.35cm) and root length (1.04 and 1.10cm) shoot (8.05mg and 7.49mg) and root dry weight (0.83 and 0.98mg) at 10 and 20oC.
Abstract: This study aimed to evaluated the surface water quality for agriculture and consumption in the Amphawa District. The surface water quality parameters in this study included water temperature, turbidity, conductivity, salinity, pH, dissolved oxygen, BOD, nitrate, suspended solids, phosphorus, total dissolved solids (TDS), iron (Fe), copper (Cu), zinc (Zn), manganese (Mn), lead (Pb) and cadmium (Cd). The water samples were collected from small excavation, Lychee, Pomelo and Coconut orchards for 3 seasons from January to December 2011.
The surface water quality from small excavation, Lychee, pomelo and coconut orchards were met the type III of surface water quality standard. The concentration of heavy metal and did not differ significantly at 0.05 level, except dissolved oxygen.
The surface water was suitable for consumption by the usual sterile and generally improving water quality through the process before and was suitable for agriculture.
Abstract: A salinity gradient solar pond is a free energy source system for collecting, convertingand storing solar energy as heat. In thispaper, the principles of solar pond are explained. A mathematical model is developed to describe and simulate heat and mass transferbehaviour of salinity gradient solar pond. MATLAB codes are programmed to solve the one dimensional finite difference method for heat and mass transfer equations. Temperature profiles and concentration distributions are calculated. The numerical results are validated with experimental data and the results arefound to be in good agreement.
Abstract: The mixture between two fluids of different salinity has been proven to capable of producing electricity in an ocean salinity energy conversion system known as hydrocratic generator. The system relies on the difference between the salinity of the incoming fresh water and the surrounding sea water in the generator. In this investigation, additional parameter is introduced which is the temperature difference between the two fluids; hence the system is known as Ocean Salinity and Temperature Energy Conversion System (OSTEC). The investigation is divided into two papers. This first paper of Part 1 presents the theoretical formulation by considering the effect of fluid dynamic viscosity known as Viscosity Model and later compares with the conventional formulation which is Density Model. The dynamic viscosity model is used to predict the dynamic of the fluids in the system which in turns gives the analytical formulation of the potential power output that can be harvested.
Abstract: Use of microemulsion in enhanced oil recovery has become more attractive in recent years because of its high level of extraction efficiency. Experimental investigations have been made on characterization of microemulsions of oil-brinesurfactant/ cosurfactant system for its use in enhanced oil recovery (EOR). Sodium dodecyl sulfate, propan-1-ol and heptane were selected as surfactant, cosurfactant and oil respectively for preparation of microemulsion. The effects of salinity on the relative phase volumes and solubilization parameters have also been studied. As salinity changes from low to high value, phase transition takes place from Winsor I to Winsor II via Winsor III. Suitable microemulsion composition has been selected based on its stability and ability to reduce interfacial tension. A series of flooding experiments have been performed using the selected microemulsion. The flooding experiments were performed in a core flooding apparatus using uniform sand pack. The core holder was tightly packed with uniform sands (60-100 mesh) and saturated with brines of different salinities. It was flooded with the brine at 25 psig and the absolute permeability was calculated from the flow rate of the through sand pack. The sand pack was then flooded with the crude oil at 800 psig to irreducible water saturation. The initial water saturation was determined on the basis of mass balance. Waterflooding was conducted by placing the coreholder horizontally at a constant injection pressure at 200 pisg. After water flooding, when water-cut reached above 95%, around 0.5 pore volume (PV) of the above microemulsion slug was injected followed by chasing water. The experiments were repeated using different composition of microemulsion slug. The additional recoveries were calculated by material balance. Encouraging results with additional recovery more than 20% of original oil in place above the conventional water flooding have been observed.
Abstract: A study was conducted in greenhouse environment to
determine the response of five tissue-cultured date palm cultivars, Al-
Ahamad, Nabusaif, Barhee, Khalas, and Kasab to irrigation water
salinity of 1.6, 5, 10, or 20 dS/ m. The salinity level of 1.6dS/m, was
used as a control. The effects of high salinity on plant survival were
manifested at 360 days after planting (DAP) onwards. Three
cultivars, Khalas, Kasab and Barhee were able to tolerate 10 dS/m
salinity level at 24 months after the start of study. Khalas tolerated
the highest salinity level of 20 dS/ m and 'Nabusaif' was found to be the
least tolerant cv. The average heights of palms and the number of
fronds were decreased with increasing salinity levels as time
progressed.
Abstract: There is strong evidence that water channel proteins
'aquaporins (AQPs)' are central components in plant-water relations
as well as a number of other physiological parameters. We had
previously reported the isolation of 24 plasma membrane intrinsic
protein (PIP) type AQPs. However, the gene numbers in rice and the
polyploid nature of bread wheat indicated a high probability of
further genes in the latter. The present work focused on identification
of further AQP isoforms in bread wheat. With the use of altered
primer design, we identified five genes homologous, designated
PIP1;5b, PIP2;9b, TaPIP2;2, TaPIP2;2a, TaPIP2;2b. Sequence
alignments indicate PIP1;5b, PIP2;9b are likely to be homeologues of
two previously reported genes while the other three are new genes
and could be homeologs of each other. The results indicate further
AQP diversity in wheat and the sequence data will enable physical
mapping of these genes to identify their genomes as well as genetic to
determine their association with any quantitative trait loci (QTLs)
associated with plant-water relation such as salinity or drought
tolerance.
Abstract: Evaluation of crop plants resistance to environmental
stresses specially in germination stage is a critical factor in their
selection in different conditions of cultivation. Therefore use of a
procedure in controllable situation can help to evaluate plants
reaction to stress quickly and precisely. In order to study germination
characteristics of flax in water and salinity stress conditions were
conducted two laboratories experimental. The two experimental were
conducted in 4-replicant completing random design for salinity and
water stress. The treatment, for salinity and water stress was three
potential (zero, 40, 80 mM) of NaCl and three potential (zero, -2, -4
bar) of PEG respectively. Germination percentage and rate, in
addition to Radical and plumule length and dry-weight and
plumule/Radical ration were measured. All of characteristics reduce
under water stress conditions. salinity stress significant reduce
germination rate and Radical and plumule length of flax seeds.
Hydropriming and osmopriming significant increased germination
rate, plumule length and plumule/Radical ration ration of flax seeds.
But germination percentage and Radical and plumule dry weight
significant increased only in hydropriming treat. Hydropriming and
osmopriming could not be used to improved germination under saline
and drought stress. But has more tolerance in salinity and drought
stress in flax by less reduce in Radical and plumule length under
saline and drought stress.
Abstract: Researchers have long had trouble in measurement of
Exchangeable Sodium Ratio (ESR) at salt-affected soils. this
parameter are often determined using laborious and time consuming
laboratory tests, but it may be more appropriate and economical to
develop a method which uses a more simple soil salinity index. The
aim of this study was to determine the relationship between
exchangeable sodium ratio (ESR) and sodium adsorption ratio (SAR)
in some salt-affected soils of Khuzestan plain. To this purpose, two
experimental areas (S1, S2) of Khuzestan province-IRAN were
selected and four treatments with three replications by series of
double rings were applied. The treatments were included 25cm,
50cm, 75cm and 100cm water application. The statistical results of
the study indicated that in order to predict soil ESR based on soil
SAR the linear regression model ESR=0.2048+0.0066 SAR
(R2=0.53) & ESR=0.0564+0.0171 SAR (R2=0.76) can be
recommended in Pilot S1 and S2 respectively.
Abstract: Plant growth is affected by the osmotic stress as well as toxicity of salt in leaves. In order to study of salt stress effects on stomatal conductance and growth rate and relationship between them as wells osmotic and Na+-specific effects on these traits, four bread wheat genotypes differing in salt tolerance were selected. Salinity was applied when the leaf 4 was fully expanded. Sodium (Na+) concentrations in flag leaf blade at 3 salinity levels (0, 100 and 200 mM NaCl) were measured. Salt-tolerant genotypes showed higher stomatal conductance and growth rate compared to salt-sensitive ones. After 10 and 20 days exposure to salt, stomatal conductance and relative growth rate were reduced, but the reduction was greater in sensitive genotypes. Growth rate was reduced severely in the first period (1-10 days) of salt commencements and it was due to osmotic effect of salt not Na+ toxicity. In the second period (11-20 days) after salt treatment growth reduced only when salt accumulated to toxic concentrations in the leaves. A positive relationship between stomatal conductance and relative growth rate showed that stomatal conductance can be a reliable indicator of growth rate, and finally can be considered as a sensitive indicator of the osmotic stress. It seems 20 days after salinity, the major effect of salt, especially at low to moderate salinity levels on growth properties was due to the osmotic effect of salt, not to Na+-specific effects within the plant.
Abstract: A greenhouse experiment was conducted to investigate the effects of different types of nutrients induced salinity on the growth, membrane permeability, nitrate reductase activity, proline content and macronutrient concentrations of tomato plants. The plants were subjected to six different treatments: 1 (control) containing basic solution, 2 basic solution+40mM of NaCl, 3 basic solution+40 mM of KNO3, 4 basic solution+20 mM of Ca(NO3)2.4H2O, 5 basic solution+20 mM of Mg(NO3)2.6H2O and 6 basic solution+20 mM of KNO3+5 mM of Ca(NO3)2.4H2O+5 mM of Mg(NO3)2.6H2O. Membrane permeability was increased significantly only with addition of NaCl, and then decreased to its lower level with addition of Ca(NO3)2.4H2O and Mg(NO3)2.6H2O. Proline accumulation were followed the same trend of results when they had been exposed to NaCl salinity. Nitrate reductase activity (NRA) was significantly affected by addition of different types of nutrient induced salinity.
Abstract: Monitoring of microbial flora in aquacultured sea bream, in relation to the physicochemical parameters of the rearing seawater, ended to a model describing the influence of the last to the quality of the fisheries. Fishes were sampled during eight months from four aqua farms in Western Greece and analyzed for psychrotrophic, H2S producing bacteria, Salmonella sp., heterotrophic plate count (PCA), with simultaneous physical evaluation. Temperature, dissolved oxygen, pH, conductivity, TDS, salinity, NO3 - and NH4 + ions were recorded. Temperature, dissolved oxygen and conductivity were correlated, respectively, to PCA, Pseudomonas sp. and Shewanella sp. counts. These parameters were the inputs of the model, which was driving, as outputs, to the prediction of PCA, Vibrio sp., Pseudomonas sp. and Shewanella sp. counts, and fish microbiological quality. The present study provides, for the first time, a ready-to-use predictive model of fisheries hygiene, leading to an effective management system for the optimization of aquaculture fisheries quality.
Abstract: The objective of this research was to identify the
vegetation-soil relationships in Nodushan arid rangelands of Yazd. 5
sites were selected for measuring the cover of plant species and soil
attributes. Soil samples were taken in 0-10 and 10-80 cm layers. The
species studied were Salsola tomentosa, Salsola arbuscula, Peganum
harmala, Zygophylum eurypterum and Eurotia ceratoides. Canonical
correspondence analysis (CCA) was used to analyze the data. Based
on the CCA results, 74.9 % of vegetation-soil variation was explained
by axis 1-3. Axis 1, 2 and 3 accounted for 27.2%, 24.9 % and 22.8%
of variance respectively. Correlation between axis 1, 2, 3 and speciesedaphic
variables were 0.995, 0.989, 0.981 respectively. Soil texture,
lime, salinity and organic matter significantly influenced the
distribution of these plant species. Determination of soil-vegetation
relationships will be useful for managing and improving rangelands
in arid and semi arid environments.
Abstract: Nowadays, biometrical characterizations of Artemia
cysts are used as one of the most important factors in the study of
Artemia populations and intraspecific particularity; meanwhile these
characters can be used as economical indices. For example, typically
high hatching efficiency is possible due to the small diameter of
cysts (high number per gram); therefore small diameter of cysts
show someway high quality of cysts. This study was performed
during a ten year period, including two different ecological
conditions: rainy and drought. It is important from two different
aspects because it covers alteration of A. urmiana during ten years
also its variation in the best and worst environmental situations in
which salinity increased from 173.8 ppt in 1994 to 280.8 ppt in
2003/4. In this study the biometrical raw data of Artemia urmiana
cysts at seven stations from the Urmia Lake in 1994 and their seven
identical locations at 26 studied stations in 2003/4 were reanalyzed
again and compared together. Biometrical comparison of untreated
and decapsulated cysts in each of the seven similar stations showed a
highly significant variation between 1994 and 2003/4. Based on this
study, in whole stations the untreated and decapsulated cysts from
1994 were larger than cysts of 2003/4 without any exception. But
there was no logical relationship between salinity and chorion
thickness in the Urmia Lake. With regard to PCA analyses the
stations of two different studied years certainly have been separated
with factor 1 from each other. In conclusion, the interaction between
genetic and environmental factors can determine and explain
variation in the range of cysts diameter in Artemia.