Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: Froth flotation remains to date as one of the most used
metallurgical processes for concentrating metal-bearing minerals in
ores. Oxide ores are relatively less amenable to froth flotation and
require a judicious choice of reagents for the recovery of metals to be
optimised. Laboratory batch flotation tests were conducted to
determine the effect of two types of gasoil-rinkalore mixtures on the
flotation response of a copper cobalt oxide ore sample. The head
assay conducted on the initial ore sample showed that it contained
about 2.90% of Cu, 0.12% of Co.
Upon the flotation test work, the results obtained indicated that the
concentrate obtained with use of the mixture gazoil-rinkalore RX
yielded 8.24% Cu and 0.22% Co concentrate grades with recoveries
of 76.0% Cu and 78.0% Co respectively. But, the concentrate
obtained by use of the mixture gazoil-rinkalore RX3 yielded
relatively bad results with 5.92% Cu and 0.18% Cu concentrate
grades with recoveries of 70.3% Cu and 65.3% Co respectively.
Abstract: Remote sensing plays a vital role in mapping of
resources and monitoring of environments of the earth. In the present
research study, mapping and monitoring of clay siltations occurred in
the Alkhod Dam of Muscat, Sultanate of Oman are carried out using
low-cost multispectral Landsat and ASTER data. The dam is
constructed across the Wadi Samail catchment for ground water
recharge. The occurrence and spatial distribution of siltations in the
dam are studied with five years of interval from the year 1987 of
construction to 2014. The deposits are mainly due to the clay, sand
and silt occurrences derived from the weathering rocks of ophiolite
sequences occurred in the Wadi Samail catchment. The occurrences
of clays are confirmed by minerals identification using ASTER
VNIR-SWIR spectral bands and Spectral Angle Mapper supervised
image processing method. The presence of clays and their spatial
distribution are verified in the field. The study recommends the
technique and the low-cost satellite data to similar region of the
world.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: Boron-gypsum is a waste which occurs in the boric
acid production process. In this study, the boron content of this waste
is evaluated for the use in synthesis of magnesium borates and such
evaluation of this kind of waste is useful more than storage or
disposal. Magnesium borates, which are a sub-class of boron
minerals, are useful additive materials for the industries due to their
remarkable thermal and mechanical properties. Magnesium borates
were obtained hydrothermally at different temperatures. Novelty of
this study is the search of the solution density effects to magnesium
borate synthesis process for the increasing the possibility of borongypsum
usage as a raw material. After the synthesis process, products
are subjected to XRD and FT-IR to identify and characterize their
crystal structure, respectively.
Abstract: In this research, it is aimed not only microwave synthesis of magnesium borates but also evaluation of magnesium wastes. Synthesis process can be described with the reaction of Mg wastes and boric acid using microwave energy. X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) were applied to synthesized minerals. According to XRD results, magnesium borate hydrate mixtures were obtained as mcallisterite (pdf# = 01-070-1902, Mg2(B6O7(OH)6)2.9(H2O)) at higher crystallinity properties was achieved at the mole ratio raw material 1:1. Also, other kinds of magnesium borate hydrates were obtained at lower crystallinity such as admontite (pdf # = 01-076-0540, MgO(B2O3)3.7(H2O)), inderite (pdf # = 01-072-2308, 2MgO.3B2O3.15(H2O)) and magnesium borate hydrates (pdf # = 01-076-0539, MgO(B2O3)3.6(H2O)). FT-IR spectrums indicated that minor changes were seen at the band values of characteristic stretching in each experiment. At the end of experiments it is seen that using microwave energy may contribute positive effects to design of synthesis process such as reducing reaction time and products at higher crystallinity.
Abstract: Stoneware clay, fired clay (as a grog), calcite waste and class C fly ash in various mixing rations were the basic raw materials for the mixture for production of dry pressed ceramic tiles. Mechanical properties (water absorption, bulk density, apparent porosity, flexural strength) as well as mineralogical composition were studied on samples with different source of calcium oxide after firing at 900, 1000, 1100 and 1200°C. It was found that samples with addition of calcite waste contain dmisteinbergit and anorthite. This minerals help to improve the strength of the body and reduce porosity fired at lower temperatures. Class C fly ash has not significantly influence on properties of the fired body as calcite waste.
Abstract: Microfibrous palygorskite and tubular halloysite clay mineral combined with nanocrystalline TiO2 are incorporating in the preparation of nanocomposite films on glass substrates via sol-gel route at 450oC. The synthesis is employing nonionic surfactant molecule as pore directing agent along with acetic acid-based sol-gel route without addition of water molecules. Drying and thermal treatment of composite films ensure elimination of organic material lead to the formation of TiO2 nanoparticles homogeneously distributed on the palygorskite or halloysite surfaces. Nanocomposite films without cracks of active anatase crystal phase on palygorskite and halloysite surfaces are characterized by microscopy techniques, UV-Vis spectroscopy, and porosimetry methods in order to examine their structural properties.
The composite palygorskite-TiO2 and halloysite-TiO2 films with variable quantities of palygorskite and halloysite were tested as photocatalysts in the photo-oxidation of Basic Blue 41 azo dye in water. These nanocomposite films proved to be most promising photocatalysts and highly effective to dye’s decoloration in spite of small amount of palygorskite-TiO2 or halloysite-TiO2 catalyst immobilized onto glass substrates mainly due to the high surface area and uniform distribution of TiO2 on clay minerals avoiding aggregation.
Abstract: The Proton Exchange Membranes (PEM) are largely studied because they operate at low temperatures and they are suitable for mobile applications. However, there are some deficiencies in their operation, mainly those that use ethanol as a hydrogen source, that require a certain attention. Therefore, this research aimed to develop Nafion® composite membranes, mixing clay minerals, kaolin and halloysite to the polymer matrix in order to improve the ethanol molecule retentions and, at the same time, to keep the system’s protonic conductivity. The modified Nafion/Kaolin, Nafion/Halloysite composite membranes were prepared in weight proportion of 0.5, 1.0 and 1.5. The membranes obtained were characterized as to their ethanol permeability, protonic conductivity and water absorption. The composite morphology and structure are characterized by SEM and EDX and the thermal behavior is determined by TGA and DSC. The analysis of the results shows ethanol permeability reduction from 48% to 63%. However, the protonic conductivity results are lower in relation to pure Nafion®. As to the thermal behavior, the Nafion® composite membranes were stable up to a temperature of 325ºC.
Abstract: The waste agriculture materials cause environment pollution, recycle of these materials help sustainable development. This study focused on the impact of used oil palm shell ash on the compressive and flexural strengths of cement mortar. Two different cement mortar mixes have been designed to investigate the impact of oil palm shell ash on strengths of cement mortar. Quantity of 4% oil palm shell ash has been replaced in cement mortar. The main objective of this paper is, to modify mechanical properties of cement mortar by replacement of oil palm ash in it at early age of 7 days. The results have been revealed optimum quantity of oil palm ash for replacement in cement mortar. The deflection, load to failure, time to failure of compressive strength and flexural strength of all specimens have significantly been improved. The stress-strain behavior has been indicated ability of modified cement mortar in control stress path and strain. The micro property of cement paste has not been investigated.
Abstract: Antioxidant properties and nutritive values of raw and cooked Pool barb, Puntius sophore (Hamilton-Buchanan) of Eastern Himalayas, India were determined. Antioxidant activity of the methanol extract of the raw, steamed, fried and curried Pool barb was evaluated by using 1,1-diphenyl-2-picrylhydrazyl (DPPH) scavenging assay. In DPPH scavenging assay the IC50 value of the raw, steamed, fried and curried Pool barb was 1.66 micro-gram/ml, 16.09 micro-gram/ml, 8.99 micro-gram/ml, 0.59 micro-gram/ml whereas the IC50 of the reference ascorbic acid was 46.66miro-gram/ml. These results showed that the fish have high antioxidant activity. Protein content was found highest in raw (20.50±0.08%) and lowest in curried (18.66±0.13%). Moisture content in raw, fried and curried was 76.35±0.09, 46.27±0.14 and 57.46±0.24 respectively. Lipid content was recorded 2.46±0.14% in raw and 21.76±0.10% in curried. Ash content varied from 12.57±0.11 to 22.53±0.07%. The total amino acids varied from 36.79±0.02 and 288.43±0.12 mg/100g. Eleven essential mineral elements were found abundant in all the samples. The samples had considerable amount of Fe ranging from 152.17 to 320.39 milli-gram/100gram, Ca 902.06 to 1356.02 milli-gram/100gram, Zn 91.07 to 138.14 milli-gram/100gram, K 193.25 to 261.56 milli-gram/100gram, Mg 225.06 to 229.10 milli-gram/100gram. Ni was not detected in the curried fish. The Mg and K contents were significantly decreased in frying method; however the Fe, Cu, Ca, Co and Mn contents were increased significantly in all the cooked samples. The Mg and Na contents were significantly increased in curried sample and the Cr content was decreased significantly (p
Abstract: Soymilk residue is obtained as a byproduct from soymilk and tofu production with little economic value. It contains high protein and fiber as well as various minerals and phyto-chemical compounds. The objective of this research was to substitute soymilk residue for wheat flour in gyoza skin in order to enhance value of soymilk residue and increase protein and fiber content of gyoza skin. Wheat flour was replaced with soymilk residue from 0 to 40%. The soy milk residue prepared in this research contains 26.92%protein, 3.58% fiber, 2.88% lipid, 6.29% ash and 60.33% carbohydrate. The results showed that increasing soymilk residue decreased lightness (L*value), tensile strength and sensory attributes but increased redness (a*), yellowness (b*), protein and fiber contents of product. The result also showed that the gyoza skin substituted with 30% soymilk residue was the most acceptable (p≤0.05) and its protein and fiber content increased up to 45 % and 867 % respectively.
Abstract: In this research, copper borates are synthesized by the
reaction of copper sulfate pentahydrate (CuSO4.5H2O) and
tincalconite (Na2O4B7.10H2O). The experimental parameters are
selected as 80oC reaction temperature and 60 of reaction time. The
effect of mole ratio of CuSO4.5H2O to Na2O4B7.5H2O is studied. For
the identification analyses X-Ray Diffraction (XRD) and Fourier
Transform Infrared Spectroscopy (FT-IR) techniques are used. At the
end of the experiments, synthesized copper borate is matched with
the powder diffraction file of “00-001-0472” [Cu(BO2)2] and
characteristic vibrations between B and O atoms are seen. The proper
crystals are obtained at the mole ratio of 3:1. This study showed that
simplified synthesis process is suitable for the production of copper
borate minerals.
Abstract: Satellite images interpretation and analysis assist geologists by providing valuable information about geology and minerals of an area to be surveyed. A test site in Fatejang of district Attock has been studied using Landsat ETM+ and ASTER satellite images for lithological mapping. Five different supervised image classification techniques namely maximum likelihood, parallelepiped, minimum distance to mean, mahalanobis distance and spectral angle mapper have been performed upon both satellite data images to find out the suitable classification technique for lithological mapping in the study area. Results of these five image classification techniques were compared with the geological map produced by Geological Survey of Pakistan. Result of maximum likelihood classification technique applied on ASTER satellite image has highest correlation of 0.66 with the geological map. Field observations and XRD spectra of field samples also verified the results. A lithological map was then prepared based on the maximum likelihood classification of ASTER satellite image.
Abstract: The influence of copper and zinc supplements on milk
production performances and health indicators was tested in a 20-
week feeding trial, with 40 Holstein-Friesian lactating cows, devided
in four groups (copper, zinc, copper-zinc and control). Correlations of
the Cu and Zn plasma values with some animal performance criteria
of health (body condition score and somatic cell counts) and
production (milk yield, peak milk yield, fat and crude protein
content) were done. During the 140 days of the experiment, the two
added minerals caused a statistically significant increase (p < 0.05) of
their plasma values after the peak of the cows’ lactations. It was also
observed that subjects that have received copper and zinc
supplements had the lowest number of somatic cell counts in milk.
The Pearson correlation test showed a positive corellation (p = 0.007,
r = + 0.851) between the plasma Zn and the milk production. The
improvement of the nutritional status improved the milk production
performances of the cows as well as their health performances.
Abstract: In order to Study the efficacy application of green
manure as chickpea pre plant, field experiments were carried out in
2007 and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on grain
yield and yield component, minerals, organic compounds and
cooking time of chickpea. Experimental units were arranged in splitsplit
plots based on randomized complete blocks with three
replications. Main plots consisted of (G1): establishing a mixed
vegetation of Vicia panunica and Hordeum vulgare and (G2):
control, as green manure levels. Also, five strategies for obtaining the
base fertilizer requirement including (N1): 20 t.ha-1 farmyard manure;
(N2): 10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5): 10 t.ha-1
farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1 triple super
phosphate were considered in sub plots. Furthermoree four levels of
biofertilizers consisted of (B1): Bacillus lentus + Pseudomonas
putida; (B2): Trichoderma harzianum; (B3): Bacillus lentus +
Pseudomonas putida + Trichoderma harzianum; and (B4): control
(without biofertilizers) were arranged in sub-sub plots. Results
showed that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield were
obtained in G1×N5 interaction. Comparison of all 2-way and 3-way
interactions showed that G1N5B3 was determined as the superior
treatment. Significant increasing of N, P2O5, K2O, Fe and Mg content
in leaves and grains emphasized on superiority of mentioned
treatment because each one of these nutrients has an approved role in
chlorophyll synthesis and photosynthesis abilities of the crops. The
combined application of compost, farmyard manure and chemical
phosphorus (N5) in addition to having the highest yield, had the best
grain quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: Paleoclimate was reconstructed by the clay mineral
assemblages of shale units of Pabdeh (Paleocene- Oligocene), Gurpi
(Upper Cretaceous), Kazhdumi (Albian-Cenomanian) and Gadvan
(Aptian-Neocomian) formations in the Bangestan anticline. To
compare with clay minerals assemblages in these formations,
selected samples also taken from available formations in drilled wells
in Ahvaz, Marun, Karanj, and Parsi oil fields. Collected samples
prepared using standard clay mineral methodology. They were
treated as normal, glycolated and heated oriented glass slides. Their
identification was made on X-Ray diffractographs. Illite % varies
from 8 to 36. Illite quantity increased from Pabdeh to Gurpi
Formation. This may be due to dominant dry climate. Kaolinite is in
range of 12-49%. Its variation style in different formations could be a
marker of climate changes from wet to dry which is supported by the
lithological changes. Chlorite (4-28%) can also be detected in those
samples without any kaolinite. Mixed layer minerals as the mixture
of illite-chlorite and illite-vermiculite-montmorillonite are varied
from 6 to 36%, decreased during Kazhdumi deposition from the base
to the top. This result may be according to decreasing of illite
leaching process. Vermiculite was also determined in very less
quantity and found in those units without kaolinite. Montmorillonite
varies from 8 to 43%, and its presence is due to terrestrial
depositional condition. Stratigraphical documents is also supported
this idea that clay mineral distribution is a function of the climate
changes. It seems, thus, the present results can be indicated a possible
procedure for ancient climate changes evaluation.
Abstract: Dehydration behavior gives a hint about thermal properties of materials. It is important for the usage areas and transportation of minerals. Magnesium borates can be used as additive materials in areas such as in the production of superconducting materials, in the composition of detergents, due to the content of boron in the friction-reducing additives in oils and insulating coating compositions due to their good mechanic and thermal properties.
In this study, thermal dehydration behavior of admontite (MgO(B2O3)3.7(H2O)), which is a kind of magnesium borate mineral, is experimented by microwave energy at 360W. Structure of admontite is suitable for the investigation of dehydration behavior by microwave because of its seven moles of crystal water. It is seen that admontite lost its 28.7% of weight at the end of the 120 minutes heating in microwave furnace.
Abstract: Calcite aCalcite and aragonite are the two common
polymorphs of CaCO3 observed as biominerals. It is universal that
the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM).
In vivo crystallization, Mg2+ inhibits calcite formation. For this
reason, stony corals skeleton may be formed only aragonite crystals
in the biocalcification. It is special in case of soft corals of which
formed only calcite crystal; however, this interesting phenomenon,
still uncharacterized in the marine environment, has been explored in
this study using newly purified cell-free proteins isolated from the
endoskeletal sclerites of soft coral. By recording the decline of pH in
vitro, the control of CaCO3 nucleation and crystal growth by the cellfree
proteins was revealed. Using Atomic Force Microscope, here we
find that these endoskeletal cell-free proteins significantly design the
morphological shape in the molecular-scale kinetics of crystal
formation and those proteins act as surfactants to promote ion
attachment at calcite steps.nd aragonite are the two common polymorphs of CaCO3 observed as biominerals. It is universal that the sea water contents a high Mg2+ (50mM) relative to Ca2+ (10mM). In vivo crystallization, Mg2+ inhibits calcite formation. For this reason, stony corals skeleton may be formed only aragonite crystals in the biocalcification. It is special in case of soft corals of which formed only calcite crystal; however, this interesting phenomenon, still uncharacterized in the marine environment, has been explored in this study using newly purified cell-free proteins isolated from the endoskeletal sclerites of soft coral. By recording the decline of pH in vitro, the control of CaCO3 nucleation and crystal growth by the cell-free proteins was revealed. Using Atomic Force Microscope, here we find that these endoskeletal cell-free proteins significantly design the morphological shape in the molecular-scale kinetics of crystal formation and those proteins act as surfactants to promote ion attachment at calcite steps. KeywordsBiomineralization, Calcite, Cell-free protein, Soft coral
Abstract: Supplement use is common in athletes. Besides their cost, they may have side effects on health and performance. 250 questionnaires were distributed among female athletes (mean age 27.08 years). The questionnaire aimed to explore the frequency, type, believes, attitudes and knowledge regarding dietary supplements. Knowledge was good in 30.3%, fair in 60.2%, and poor in 9.1% of respondents. 65.3% of athletes did not use supplements regularly. The most widely used supplements were vitamins (48.4%), minerals (42.9%), energy supplements (21.3%), and herbals (20.9%). 68.9% of athletes believed in their efficacy. 34.4% experienced performance enhancement and 6.8% of reported side effects. 68.2% reported little knowledge and 60.9% were eager to learn more. In conclusion, many of the female athletes believe in the efficacy of supplements and think they are an unavoidable part of competitive sports. However, their information is not sufficient. We have to stress on education, consulting sessions, and rational prescription.