Abstract: The Želazny Most tailing pond is one of the largest
facilities worldwide for waste disposal from the copper mines located
in South-West Poland. A potential failure of the dam would allow
more than 10 million cubic meters of contaminated slurry to flow to
the valley, causing immense environmental problems to the
surrounding area. Thus, the determination of the strength properties
of the dam's soils and their variability is of utmost importance.
An extensive site investigation consisting of more than 480 cone
penetration tests (CPTs) with or without pore water pressure
measurements were conducted within a period of 13 years to study
the mechanical properties of the tailings body. The present work
investigates the point variability of the soil strength parameters
(effective friction angle
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: The purpose of this research study is to investigate the manner in which various loads affect the mechanical properties of the formed mild steel plates. The investigation focuses on examining the cross-sectional area of the metal plate at the centre of the formed mild steel plate. Six mild steel plates were deformed with different loads. The loads applied on the plates had a magnitude of 5 kg, 10 kg, 15 kg, 20 kg, 25 kg and 30 kg. The radius of the punching die was 120 mm and the loads were applied at room temperature. The investigations established that the applied load causes the Vickers microhardness at the cross-sectional area of the plate to increase due to strain hardening. Hence, the percentage increase of the hardness due to the load was found to be directly proportional to the increase in the load. Furthermore, the tensile test results for the parent material showed that the average Ultimate Tensile Strength (UTS) for the three samples was 308 MPa while the average Yield Strength and Percentage Elongation were 227 MPa and 38 % respectively. Similarly, the UTS of the formed components increased after the deformation of the plate, as such it can be concluded that the forming loads alter the mechanical properties of the materials by improving and strengthening the material properties.
Abstract: Bionanotechnology deals with nanoscopic interactions between nanostructured materials and biological systems. Polymer nanocomposites with optimized biological activity have attracted great attention. Nanoclay is considered as reinforcing nanofiller in manufacturing of high performance nanocomposites. In current study, organomodified-nanoclay with negatively charged silicate layers was incorporated into biomedical grade silicone rubber. Nanoparticle loading has been tailored to enhance cell behavior. Addition of nanoparticles led to improved mechanical properties of substrate with enhanced strength and stiffness while no toxic effects was observed. Results indicated improved viability and proliferation of cells by addition of nanofillers. The improved mechanical properties of the matrix result in proper cell response through adjustment and arrangement of cytoskeletal fibers. Results can be applied in tissue engineering when enhanced substrates are required for improvement of cell behavior for in vivo applications.
Abstract: This study systemizes processes and methods in
wooden furniture design that contains uniqueness in function and
aesthetics. The study was done by research and analysis for
designer-s consideration factors that affect function and production.
Therefore, the study result indicates that such factors are design
process (planning for design, product specifications, concept design,
product architecture, industrial design, production), design evaluation
as well as wooden furniture design dependent factors i.e. art (art
style; furniture history, form), functionality (the strength and
durability, area place, using), material (appropriate to function, wood
mechanical properties), joints, cost, safety, and social responsibility.
Specifically, all aforementioned factors affect good design. Resulting
from direct experience gained through user-s usage, the designer
must design the wooden furniture systemically and effectively. As a
result, this study selected dinning armchair as a case study with all
involving factors and all design process stated in this study.
Abstract: Novel acrylated epoxidized hemp oil (AEHO) based
bioresins were successfully synthesised, characterized and applied to
biocomposites reinforced with woven jute fibre. Characterisation of
the synthesised AEHO consisted of acid number titrations and FTIR
spectroscopy to assess the success of the acrylation reaction. Three
different matrices were produced (vinylester (VE), 50/50 blend of
AEHO/VE and 100% AEHO) and reinforced with jute fibre to form
three different types of biocomposite samples. Mechanical properties
in the form of flexural and interlaminar shear strength (ILSS) were
investigated and compared for the different samples. Results from the
mechanical tests showed that AEHO and 50/50 based neat bioresins
displayed lower flexural properties compared with the VE samples.
However when applied to biocomposites and compared with VE
based samples, AEHO biocomposites demonstrated comparable
flexural performance and improved ILSS. These results are attributed
to improved fibre-matrix interfacial adhesion due to surface-chemical
compatibility between the natural fibres and bioresin.
Abstract: Particle boards were prepared from Maize cob (MC) and urea-formaldehyde resin (UFR) on compression moulding machine. The amount of MC was varied from 50-120g while 30g of UFR was kept constant. Some mechanical properties of the particle boards were tested using the standard ASM methods. The results show that as the MC content increased from 50- 120g in 30g UFR, the hardness increased from about 6.89 x 102 to7.51 x 102MPa. Impact strength decreased from 3.3x 10-2 to 0.45 x 10-2J/M2, while tensile strength initially increased from 2.63 x 102 to 3.14 x 102 MPa as the MC increased from 50 to 60g in 30g UFR, thereafter, it decreased to about 1.35 x 102MPa at 120g in 30g content.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.
Abstract: The term hybrid composite refers to the composite
containing more than one type of fiber material as reinforcing fillers.
It has become attractive structural material due to the ability of
providing better combination of properties with respect to single fiber
containing composite. The eco-friendly nature as well as processing
advantage, light weight and low cost have enhanced the attraction
and interest of natural fiber reinforced composite. The objective of
present research is to study the mechanical properties of jute-coir
fiber reinforced hybrid polypropylene (PP) composite according to
filler loading variation. In the present work composites were
manufactured by using hot press machine at four levels of fiber
loading (5, 10, 15 and 20 wt %). Jute and coir fibers were utilized at a
ratio of (1:1) during composite manufacturing. Tensile, flexural,
impact and hardness tests were conducted for mechanical
characterization. Tensile test of composite showed a decreasing trend
of tensile strength and increasing trend of the Young-s modulus with
increasing fiber content. During flexural, impact and hardness tests,
the flexural strength, flexural modulus, impact strength and hardness
were found to be increased with increasing fiber loading. Based on
the fiber loading used in this study, 20% fiber reinforced composite
resulted the best set of mechanical properties.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Abstract: To improve the material characteristics of single- and
poly-crystals of pure copper, the respective relationships between crystallographic orientations and microstructures, and the bending and mechanical properties were examined. And texture distribution is also
analyzed. A grain refinement procedure was performed to obtain a
grained structure. Furthermore, some analytical results related to
crystal direction maps, inverse pole figures, and textures were obtained from SEM-EBSD analyses. Results showed that these
grained metallic materials have peculiar springback characteristics with various bending angles.
Abstract: This paper presents a generalized formulation for the
problem of buckling optimization of anisotropic, radially graded,
thin-walled, long cylinders subject to external hydrostatic pressure.
The main structure to be analyzed is built of multi-angle fibrous
laminated composite lay-ups having different volume fractions of the
constituent materials within the individual plies. This yield to a
piecewise grading of the material in the radial direction; that is the
physical and mechanical properties of the composite material are
allowed to vary radially. The objective function is measured by
maximizing the critical buckling pressure while preserving the total
structural mass at a constant value equals to that of a baseline
reference design. In the selection of the significant optimization
variables, the fiber volume fractions adjoin the standard design
variables including fiber orientation angles and ply thicknesses. The
mathematical formulation employs the classical lamination theory,
where an analytical solution that accounts for the effective axial and
flexural stiffness separately as well as the inclusion of the coupling
stiffness terms is presented. The proposed model deals with
dimensionless quantities in order to be valid for thin shells having
arbitrary thickness-to-radius ratios. The critical buckling pressure
level curves augmented with the mass equality constraint are given
for several types of cylinders showing the functional dependence of
the constrained objective function on the selected design variables. It
was shown that material grading can have significant contribution to
the whole optimization process in achieving the required structural
designs with enhanced stability limits.
Abstract: Sensorized instruments that accurately measure the interaction forces (between biological tissue and instrument endeffector) during surgical procedures offer surgeons a greater sense of immersion during minimally invasive robotic surgery. Although there is ongoing research into force measurement involving surgical graspers little corresponding effort has been carried out on the measurement of forces between scissor blades and tissue. This paper presents the design and development of a force measurement test apparatus, which will serve as a sensor characterization and evaluation platform. The primary aim of the experiments is to ascertain whether the system can differentiate between tissue samples with differing mechanical properties in a reliable, repeatable manner. Force-angular displacement curves highlight trends in the cutting process as well the forces generated along the blade during a cutting procedure. Future applications of the test equipment will involve the assessment of new direct force sensing technologies for telerobotic surgery.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: The present study deals with the analysis of the cylindrical part of a CNG storage vessel, combining a plastic liner and an over wrapped filament wound composite. Three kind of polymer are used in the present analysis: High density Polyethylene HDPE, Light low density Polyethylene LLDPE and finally blend of LLDPE/HDPE. The effect of the mechanical properties on the behavior of type IV vessel may be then investigated. In the present paper, the effect of the order of the circumferential winding on the stacking sequence may be then investigated. Based on mechanical considerations, the present model provides an exact solution for stresses and deformations on the cylindrical section of the vessel under thermo-mechanical static loading. The result show a good behavior of HDPE liner compared to the other plastic materials. The presence of circumferential winding angle in the stacking improves the rigidity of vessel by improving the burst pressure.
Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: The fundamental defect inherent to the thermoforming
technology is wall-thickness variation of the products due to
inadequate thermal processing during production of polymer. A
nonlinear viscoelastic rheological model is implemented for
developing the process model. This model describes deformation
process of a sheet in thermoforming process. Because of relaxation
pause after plug-assist stage and also implementation of two stage
thermoforming process have minor wall-thickness variation and
consequently better mechanical properties of polymeric articles. For
model validation, a comparative analysis of the theoretical and
experimental data is presented.