Abstract: The deformation behaviour of additively manufactured AlSi10Mg alloy under low strains, high strain rates and elevated temperature conditions is essential to analyse and predict its response against dynamic loading such as impact and thermomechanical fatigue. The constitutive relation of Johnson-Cook is used to capture the strain rate sensitivity and thermal softening effect in AlSi10Mg alloy. Johnson-Cook failure model is widely used for exploring damage mechanics and predicting the fracture in many materials. In this present work, Johnson-Cook material and damage model parameters for additively manufactured AlSi10Mg alloy have been determined numerically from four types of uniaxial tensile test. Three different uniaxial tensile tests with dynamic strain rates (0.1, 1, 10, 50, and 100 s-1) and elevated temperature tensile test with three different temperature conditions (450 K, 500 K and 550 K) were performed on 3D printed AlSi10Mg alloy in ABAQUS/Explicit. Hexahedral elements are used to discretize tensile specimens and fracture energy value of 43.6 kN/m was used for damage initiation. Levenberg Marquardt optimization method was used for the evaluation of Johnson-Cook model parameters. It was observed that additively manufactured AlSi10Mg alloy has shown relatively higher strain rate sensitivity and lower thermal stability as compared to the other Al alloys.
Abstract: Asphalt overlay is the most commonly used technique of pavement rehabilitation. However, the reflective cracks which occur on the overlay surface after a short period of time are the most important distresses threatening the durability of new overlays. Stress Absorbing Membrane Interlayers (SAMIs) are used to postpone the reflective cracking in the overlays. Sand asphalt mixtures, in unmodified or crumb rubber modified (CRM) conditions, can be used as an SAMI material. In this research, the performance properties of different SAMI applications were evaluated in the laboratory using an Indirect Tensile (IDT) fracture energy. The IDT fracture energy of sand asphalt samples was also evaluated and then compared to that of the regular dense graded asphalt used as an overlay. Texas boiling water and modified Lottman tests were also conducted to evaluate the moisture susceptibility of sand asphalt mixtures. The test results showed that sand asphalt mixtures can stand higher levels of energy before cracking, and this is even more pronounced for the CRM sand mix. Sand asphalt mixture using CRM binder was also shown to be more resistance to moisture induced distresses.
Abstract: In this study, the mechanical model of various anchors embedded in gypsum board subjected cyclic shear loading were investigated. Shear tests for anchors embedded in 200 mm square size gypsum board were conducted to measure the load - load displacement curves. The strength of the gypsum board was changed for three conditions and 12 kinds of anchors were selected which were ordinary used for gypsum board anchoring. The loading conditions were a monotonous loading and a cyclic loading controlled by a servo-controlled hydraulic loading system to achieve accurate measurement. The fracture energy for each of the anchors was estimated by the analysis of consumed energy calculated by the load - load displacement curve. The effect of the strength of gypsum board and the types of anchors on the shear properties of gypsum board anchors was cleared. A numerical model to predict the load-unload curve of shear deformation of gypsum board anchors caused by such as the earthquake load was proposed and the validity on the model was proved.
Abstract: Behavior of dams against the seismic loads has been
studied by many researchers. Most of them proposed new numerical
methods to investigate the dam safety. In this paper, to study the
effect of nonlinear parameters of concrete in gravity dams, a twodimensional
approach was used including the finite element method,
staggered method and smeared crack approach. Effective parameters
in the models are physical properties of concrete such as modulus of
elasticity, tensile strength and specific fracture energy. Two different
models were used in foundation (mass-less and massed) in order to
determine the seismic response of concrete gravity dams. Results
show that when the nonlinear analysis includes the dam- foundation
interaction, the foundation-s mass, flexibility and radiation damping
are important in gravity dam-s response.
Abstract: In order to supplement the brittle property of concrete,
fibers are added into concrete mixtures. Compared to general concrete,
various characteristics such as tensile strength, bending strength,
bending toughness, and resistance to crack are superior, and even
when cracks occur, improvements on toughness as well as resistance
to shock are excellent due to the growth of fracture energy. Increased
function of steel fiber reinforced concrete can be differentiated
depending on the fiber dispersion, and sand percentage can be an
important influence on the fiber dispersion. Therefore, in this research,
experiments were planned on sand percentage in order to apprehend
the influence of sand percentage on the bending properties and direct
tension of SFRC and basic experiments were conducted on bending
and direct tension in order to recognize the properties of bending
properties and direct tension following the size of the aggregates and
sand percentage.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.