Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: Computer aided diagnosis systems provide vital
opinion to radiologists in the detection of early signs of breast cancer
from mammogram images. Architectural distortions, masses and
microcalcifications are the major abnormalities. In this paper, a
computer aided diagnosis system has been proposed for
distinguishing abnormal mammograms with architectural distortion
from normal mammogram. Four types of texture features GLCM
texture, GLRLM texture, fractal texture and spectral texture features
for the regions of suspicion are extracted. Support vector machine
has been used as classifier in this study. The proposed system yielded
an overall sensitivity of 96.47% and an accuracy of 96% for
mammogram images collected from digital database for screening
mammography database.
Abstract: In this paper, influence of harmonics on medium
voltage distribution system of Bogazici Electricity Distribution Inc.
(BEDAS) which takes place at Istanbul/Turkey is investigated. A ring
network consisting of residential loads is taken into account for this
study. Real system parameters and measurement results are used for
simulations. Also, probable working conditions of the system are
analyzed for 50%, 75%, and 100% loading of transformers with
similar harmonic contents. Results of the study are exhibited the
influence of nonlinear loads on %THDV, P.F. and technical losses of
the medium voltage distribution system.
Abstract: The new era of digital communication has brought up
many challenges that network operators need to overcome. The high
demand of mobile data rates require improved networks, which is a
challenge for the operators in terms of maintaining the quality of
experience (QoE) for their consumers. In live video transmission,
there is a sheer need for live surveillance of the videos in order to
maintain the quality of the network. For this purpose objective
algorithms are employed to monitor the quality of the videos that are
transmitted over a network. In order to test these objective algorithms,
subjective quality assessment of the streamed videos is required, as the
human eye is the best source of perceptual assessment. In this paper we
have conducted subjective evaluation of videos with varying spatial
and temporal impairments. These videos were impaired with frame
freezing distortions so that the impact of frame freezing on the quality
of experience could be studied. We present subjective Mean Opinion
Score (MOS) for these videos that can be used for fine tuning the
objective algorithms for video quality assessment.
Abstract: This paper proposed the comparison made between
Multi-Carrier Pulse Width Modulation, Sinusoidal Pulse Width
Modulation and Selective Harmonic Elimination Pulse Width
Modulation technique for minimization of Total Harmonic Distortion
in Cascaded H-Bridge Multi-Level Inverter. In Multicarrier Pulse
Width Modulation method by using Alternate Position of Disposition
scheme for switching pulse generation to Multi-Level Inverter.
Another carrier based approach; Sinusoidal Pulse Width Modulation
method is also implemented to define the switching pulse generation
system in the multi-level inverter. In Selective Harmonic Elimination
method using Genetic Algorithm and Particle Swarm Optimization
algorithm for define the required switching angles to eliminate low
order harmonics from the inverter output voltage waveform and
reduce the total harmonic distortion value. So, the results validate that
the Selective Harmonic Elimination Pulse Width Modulation method
does capably eliminate a great number of precise harmonics and
minimize the Total Harmonic Distortion value in output voltage
waveform in compared with Multi-Carrier Pulse Width Modulation
method, Sinusoidal Pulse Width Modulation method. In this paper,
comparison of simulation results shows that the Selective Harmonic
Elimination method can attain optimal harmonic minimization
solution better than Multi-Carrier Pulse Width Modulation method,
Sinusoidal Pulse Width Modulation method.
Abstract: Submerged arc welding is a very complex process. It
is a very efficient and high performance welding process. In this
present study an attempt have been done to reduce the welding
distortion by increased amount of oxide flux through TiO2 in
submerged arc welding process. Care has been taken to avoid the
excessiveness of the adding agent for attainment of significant
results. Data Envelopment Analysis (DEA) based BAT algorithm is
used for the parametric optimization purpose in which DEA is used
to convert multi response parameters into a single response
parameter. The present study also helps to know the effectiveness of
the addition of TiO2 in active flux during submerged arc welding
process.
Abstract: A novel design technique employing CMOS Current
Feedback Operational Amplifier (CFOA) is presented. The feature of
consumption very low power in designing pseudo-OTA is used to
decreasing the total power consumption of the proposed CFOA. This
design approach applies pseudo-OTA as input stage cascaded with
buffer stage. Moreover, the DC input offset voltage and harmonic
distortion (HD) of the proposed CFOA are very low values compared
with the conventional CMOS CFOA due to the symmetrical input
stage. P-Spice simulation results are obtained using 0.18μm MIETEC
CMOS process parameters and supply voltage of ±1.2V, 50μA
biasing current. The p-spice simulation shows excellent improvement
of the proposed CFOA over existing CMOS CFOA. Some of these
performance parameters, for example, are DC gain of 62. dB, openloop
gain bandwidth product of 108 MHz, slew rate (SR+) of
+71.2V/μS, THD of -63dB and DC consumption power (PC) of
2mW.
Abstract: This article presents two methods for the
compensation of harmonics generated by a nonlinear load. The first is
the classic method P-Q. The second is the controller by modern
method of artificial intelligence specifically fuzzy logic. Both
methods are applied to a shunt Active Power Filter (sAPF) based on a
three-phase voltage converter at five levels NPC topology. In
calculating the harmonic currents of reference, we use the algorithm
P-Q and pulse generation, we use the intersective PWM. For
flexibility and dynamics, we use fuzzy logic. The results give us clear
that the rate of Harmonic Distortion issued by fuzzy logic is better
than P-Q.
Abstract: With the growing of computer and network, digital
data can be spread to anywhere in the world quickly. In addition,
digital data can also be copied or tampered easily so that the security
issue becomes an important topic in the protection of digital data.
Digital watermark is a method to protect the ownership of digital data.
Embedding the watermark will influence the quality certainly. In this
paper, Vector Quantization (VQ) is used to embed the watermark into
the image to fulfill the goal of data hiding. This kind of watermarking
is invisible which means that the users will not conscious the existing
of embedded watermark even though the embedded image has tiny
difference compared to the original image. Meanwhile, VQ needs a lot
of computation burden so that we adopt a fast VQ encoding scheme by
partial distortion searching (PDS) and mean approximation scheme to
speed up the data hiding process.
The watermarks we hide to the image could be gray, bi-level and
color images. Texts are also can be regarded as watermark to embed.
In order to test the robustness of the system, we adopt Photoshop to
fulfill sharpen, cropping and altering to check if the extracted
watermark is still recognizable. Experimental results demonstrate that
the proposed system can resist the above three kinds of tampering in
general cases.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: In this paper, a direct power control (DPC)
strategies have been investigated in order to control a high
power AC/DC converter with time variable load. This converter
is composed of a three level three phase neutral point clamped
(NPC) converter as rectifier and an H-bridge four quadrant
current control converter. In the high power application,
controller not only must adjust the desire outputs but also
decrease the level of distortions which are injected to the network
from the converter. Regarding to this reason and nonlinearity
of the power electronic converter, the conventional controllers
cannot achieve appropriate responses. In this research, the
precise mathematical analysis has been employed to design the
appropriate controller in order to control the time variable
load. A DPC controller has been proposed and simulated using
Matlab/ Simulink. In order to verify the simulation result, a real
time simulator- OPAL-RT- has been employed. In this paper,
the dynamic response and stability of the high power NPC
with variable load has been investigated and compared with
conventional types using a real time simulator. The results proved
that the DPC controller is more stable and has more precise
outputs in comparison with conventional controller.
Abstract: This paper proposes five level diode clamped Z source
Inverter. The existing PWM techniques used for ZSI are restricted for
two level. The two level Z Source Inverter have high harmonic
distortions which effects the performance of the grid connected PV
system. To improve the performance of the system the number of
voltage levels in the output waveform need to be increased. This
paper presents comparative analysis of a five level diode clamped Z
source Inverter with different carrier based Modified Pulse Width
Modulation techniques. The parameters considered for comparison
are output voltage, voltage gain, voltage stress across switch and total
harmonic distortion when powered by same DC supply. Analytical
results are verified using MATLAB.
Abstract: Multi-Level Inverter technology has been developed in the area of high-power medium-voltage energy scheme, because of their advantages such as devices of lower rating can be used thereby enabling the schemes to be used for high voltage applications. Reduced Total Harmonic Distortion (THD).Since the dv/dt is low; the Electromagnetic Interference from the scheme is low. To avoid the switching losses Lower switching frequencies can be used. In this paper present a survey of various topologies, control strategy and modulation techniques used by these inverters. Here the regenerative and superior topologies are also discussed.
Abstract: Quantification of cardiac function is performed by
calculating blood volume and ejection fraction in routine clinical
practice. However, these works have been performed by manual
contouring, which requires computational costs and varies on the
observer. In this paper, an automatic left ventricle segmentation
algorithm on cardiac magnetic resonance images (MRI) is presented.
Using knowledge on cardiac MRI, a K-mean clustering technique is
applied to segment blood region on a coil-sensitivity corrected image.
Then, a graph searching technique is used to correct segmentation
errors from coil distortion and noises. Finally, blood volume and
ejection fraction are calculated. Using cardiac MRI from 15 subjects,
the presented algorithm is tested and compared with manual
contouring by experts to show outstanding performance.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: To achieve reliable welds with minimum distortion for
the fabrication of components in aerospace industry laser beam
welding is attempted. Laser welding can provide a significant benefit
for the welding of Titanium and Aluminium thin sheet alloys of its
precision and rapid processing capability. For laser welding, pulse
shape, energy, duration, repetition rate and peak power are the most
important parameters that influence directly the quality of welds. In
this experimental work for joining 1mm thick TI6AL4V and AA2024
alloy and JK600 Nd:YAG pulsed laser units used. The distortions at
different welding power and speed of titanium and aluminium thin
sheet alloys are investigated. Test results reveal that increase in
welding speed increases distortion in weldment
Abstract: In this article is reported a construction and some
properties of the 5iD viewer, the system recording simultaneously
5 views of a given experimental object. Properties of the system
are demonstrated on the analysis of fish schooling behaviour. It
is demonstrated the method of instrument calibration which allows
inclusion of image distortion and it is proposed and partly tested
also the method of distance assessment in the case that only two
opposite cameras are available. Finally, we demonstrate how the state
trajectory of the behaviour of the fish school may be constructed from
the entropy of the system.
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: In this paper, we present a robust algorithm to recognize extracted text from grocery product images captured by mobile phone cameras. Recognition of such text is challenging since text in grocery product images varies in its size, orientation,
style, illumination, and can suffer from perspective distortion.
Pre-processing is performed to make the characters scale and
rotation invariant. Since text degradations can not be appropriately
defined using well-known geometric transformations such
as translation, rotation, affine transformation and shearing, we
use the whole character black pixels as our feature vector.
Classification is performed with minimum distance classifier
using the maximum likelihood criterion, which delivers very
promising Character Recognition Rate (CRR) of 89%. We
achieve considerably higher Word Recognition Rate (WRR) of
99% when using lower level linguistic knowledge about product
words during the recognition process.
Abstract: We report on the use of strong external optical
feedback to enhance the modulation response of semiconductor lasers
over a frequency passband around modulation frequencies higher
than 60 GHz. We show that this modulation enhancement is a type of
photon-photon resonance (PPR) of oscillating modes in the external
cavity formed between the laser and the external reflector. The study
is based on a time-delay rate equation model that takes into account
both the strong feedback and multiple reflections in the external
cavity. We examine the harmonic and intermodulation distortions
associated with single and two-tone modulations in the mm-wave
band of the resonant modulation. We show that compared with
solitary lasers modulated around the carrier-photon resonance
frequency, the present mm-wave modulated signal has lower
distortions.