Abstract: Adhesion to the human intestinal cell is considered
as one of the main selection criteria of lactic acid bacteria for
probiotic use. The adhesion ability of two Bifidobacteriums strains
Bifidobacterium longum BB536 and Bifidobacterium
psudocatenulatum G4 was done using HT-29 human epithelium
cell line as in vitro study. Four different level of pH were used 5.6,
5.7, 6.6, and 6.8 with four different times 15, 30, 60, and 120 min.
Adhesion was quantified by counting the adhering bacteria after
Gram staining. The adhesion of B. longum BB536 was higher than
B. psudocatenulatum G4. Both species showed significant
different in the adhesion properties at the factors tested. The
highest adhesion for both Bifidobacterium was observed at 120
min and the low adhesion was in 15 min. The findings of this
study will contribute to the introduction of new effective probiotic
strain for future utilization.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: research goal was to determine the expression levels cDNA of brain embrio at gestation days 10 (GD-10). The Electroforesis DNA results showed that GAPDH, Fibronectin1, Ncam1, Tenascin, Vimentin, Neurofilament heavy, Neurofilament medium and Neurofilament low were 447 bp, 462 bp, 293 bp. 416 bp, 327 bp, 301 bp, 398 bp and 289 bp. Result of real-time RT-PCR on brain Embryo at gestation days 10 showed that the expression of copy gen Fibronectin 36 copies, Ncam 21,708 copies; Tenascin 24,505 copies; Vimentin 538,554 copies; Neurofilament heavy 2,419 copies; Neurofilament medium 92,928 copies; Neurofilament low 125,809 copies. Vimentin expressed gene copies is very high compared with other gene copies. This condition are caused by Vimentin, that contribute to proliferate of brain development. The vimentin role to cell proliferation of brain.
Abstract: Environmental awareness and depletion of the
petroleum resources are among vital factors that motivate a number
of researchers to explore the potential of reusing natural fiber as an
alternative composite material in industries such as packaging,
automotive and building constructions. Natural fibers are available in
abundance, low cost, lightweight polymer composite and most
importance its biodegradability features, which often called “ecofriendly"
materials. However, their applications are still limited due
to several factors like moisture absorption, poor wettability and large
scattering in mechanical properties. Among the main challenges on
natural fibers reinforced matrices composite is their inclination to
entangle and form fibers agglomerates during processing due to
fiber-fiber interaction. This tends to prevent better dispersion of the
fibers into the matrix, resulting in poor interfacial adhesion between
the hydrophobic matrix and the hydrophilic reinforced natural fiber.
Therefore, to overcome this challenge, fiber treatment process is one
common alternative that can be use to modify the fiber surface
topology by chemically, physically or mechanically technique.
Nevertheless, this paper attempt to focus on the effect of
mercerization treatment on mechanical properties enhancement of
natural fiber reinforced composite or so-called bio composite. It
specifically discussed on mercerization parameters, and natural fiber
reinforced composite mechanical properties enhancement.
Abstract: This current research focused on development of degradable starch based packaging film with enhanced mechanical properties. A series of low density polyethylene (LDPE)/tapioca starch compounds with various tapioca starch contents were prepared by twin screw extrusion with the addition of maleic anhydride grafted polyethylene as compatibilizer. Palm cooking oil was used as processing aid to ease the blown film process, thus, degradable film can be processed via conventional blown film machine. Studies on their characteristics, mechanical properties and biodegradation were carried out by Fourier Transform Infrared (FTIR) spectroscopy and optical properties, tensile test and exposure to fungi environment respectively. The presence of high starch contents had an adverse effect on the tensile properties of LDPE/tapioca starch blends. However, the addition of compatibilizer to the blends improved the interfacial adhesion between the two materials, hence, improved the tensile properties of the films. High content of starch amount also was found to increase the rate of biodegradability of LDPE/tapioca starch films. It can be proved by exposure of the film to fungi environment. A growth of microbes colony can be seen on the surface of LDPE/tapioca starch film indicates that the granular starch present on the surface of the polymer film is attacked by microorganisms, until most of it is assimilated as a carbon source.
Abstract: A thin coating of hexamethyldisiloxane and subsequent O2-plasma treatment was performed on mirror-polished titanium in order to regulate the wide range of wettability including 106 and almost 0 degrees of contact angles. The adsorption behavior of
fibronectin and albumin in both individual and competitive mode,
and initial attachment of fibroblasts and osteoblasts were investigated.
Individually, fibronectin adsorption showed a biphasic inclination, whereas albumin showed greater adsorption to hydrophobic surfaces.
In competitive mode, in solution containing both fibronectin and albumin, fibronectin showed greater adsorption on hydrophilic
surfaces, whereas Alb predominantly adsorbed on hydrophobic
surfaces. Initial attachment of both cells increased with increase in
surface wettability, in particular, on super-hydrophilic surface, which
correlated well with fibronectin adsorption in competitive mode.
These results suggest that a cold plasma-surface modification enabled
to regulate the surface wettability, and fibronectin adsorption may be
responsible for increasing cell adhesion on hydrophilic surfaces in a
body fluid
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: The objective of this work is to study the influence of the properties of the substrate on the retrofit (thin repair) of damaged concrete elements, with the SCC. Fluidity, principal characteristic of the SCC, would enable it to cover and adhere to the concrete to be repaired. Two aspects of repair are considered, the bond (Adhesion) and the tensile strength and the cracking. The investigation is experimental; It was conducted over test specimens made up of ordinary concrete prepared and hardened in advance (the material to be repaired) over which a self compacting concrete layer is cast. Three alternatives of SC concrete and one ordinary concrete (comparison) were tested. It appears that the self-compacting concrete constitutes a good material for repairing. It follows perfectly the surfaces- forms to be repaired and allows a perfect bond. Fracture tests made on specimens of self-compacting concrete show a brittle behaviour. However when a small percentage of fibres is added, the resistance to cracking is very much improve.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: Novel acrylated epoxidized hemp oil (AEHO) based
bioresins were successfully synthesised, characterized and applied to
biocomposites reinforced with woven jute fibre. Characterisation of
the synthesised AEHO consisted of acid number titrations and FTIR
spectroscopy to assess the success of the acrylation reaction. Three
different matrices were produced (vinylester (VE), 50/50 blend of
AEHO/VE and 100% AEHO) and reinforced with jute fibre to form
three different types of biocomposite samples. Mechanical properties
in the form of flexural and interlaminar shear strength (ILSS) were
investigated and compared for the different samples. Results from the
mechanical tests showed that AEHO and 50/50 based neat bioresins
displayed lower flexural properties compared with the VE samples.
However when applied to biocomposites and compared with VE
based samples, AEHO biocomposites demonstrated comparable
flexural performance and improved ILSS. These results are attributed
to improved fibre-matrix interfacial adhesion due to surface-chemical
compatibility between the natural fibres and bioresin.