Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Abstract: Water borne polyurethane (PU) based on newly prepared hyperbranched poly (amine-ester) (HBPAE) was applied and evaluated as organic coating material. HBPAE was prepared through one-pot synthesis between trimethylol propane as a core and AB2 branched monomer which was obtained via Michal addition of methyl methacrylate (MMA) and diethanol amine (DEA). PU was prepared from HBPAE using different ratios of toluene diisocyanate (TDI) to form cured coating film. The prepared HBPAE was characterized using; GPC, FT-IR and 1H-NMR. The mechanical properties (impact, hardness, adhesion, and flexibility), thermal properties (DSC and TGA) and chemical resistance of the applied film were estimated. The results indicated 50% of TDI is the selected ratio. This formulation represents a promising candidate to be used as coating material.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: It is well known that enhancing interfacial adhesion
between inorganic filler and matrix resin in a composite lead to
favorable properties such as excellent mechanical properties, high
thermal resistance, prominent electric insulation, low expansion
coefficient, and so on. But it should be avoided that much excess of
coupling agent is reacted due to a negative impact of their final
composite-s properties. There is no report to achieve classification of
the bonding state excepting investigation of coating layer thickness.
Therefore, the analysis of the bonding state of the coupling agent
reacted with the filler surface such as BN particles with less functional
group and silica particles having much functional group was
performed by thermal gravimetric analysis and pyrolysis GC/MS. The
reacted number of functional groups on the silane-coupling agent was
classified as a result of the analysis. Thus, we succeeded in classifying
the reacted number of the functional groups as a result of this study.
Abstract: The research study was based on an evaluation of the
ability of glued test samples to pass the criterion of sufficient
bondline adhesion under the exposure conditions defined in EN 302-
1. Additionally, an infrared spectroscopic analysis of the evaluated
adhesives (phenol-resorcinol-formaldehyde PRF and melamine-ureaformaldehyde
MUF) with different mix ratios was carried out to
evaluate the possible effects of a faulty technological process.
Abstract: Hyperglycemia-mediated accumulation of advanced glycation end-products (AGEs) play a pivotal role in the development of diabetic complications by inducing inflammation. In the present study, we evaluated the possible effects of water/ethanol (1/1, v/v) extracts (WEE) and its fractions from Canarium album Raeusch. (Chinese olive) which is a fruit used on AGEs-stimulated oxidative stress and inflammation in monocytes and vascular endothelial cells. Co-incubation of EA.hy926 endothelial cells with WEE and its fractions for 24h resulted in a significant decrease of monocyte–endothelial cell adhesion, the expression of ICAM-1, generation of intracellular ROS and depletion of GSH induced by AGEs. Chinese olive fruit extracts also reduced the expression of pro-inflammatory mediates, such as TNF-α, IL-1β and IL-6 in THP-1 cells. These findings suggested that Chinese olive fruit was able to protect vascular endothelium from dysfunction induced by AGEs.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper presents an experimental investigation on
the machinability of laser-sintered material using small ball end mill focusing on wear mechanisms. Laser-sintered material was produced
by irradiating a laser beam on a layer of loose fine SCM-Ni-Cu powder. Bulk carbon steel JIS S55C was selected as a reference steel.
The effects of powder consolidation mechanisms and unsintered
powder on the tool life and wear mechanisms were carried out. Results indicated that tool life in cutting laser-sintered material is
lower than that in cutting JIS S55C. Adhesion of the work material and chipping were the main wear mechanisms of the ball end mill in
cutting laser-sintered material. Cutting with the unsintered powder
surrounding the tool and laser-sintered material had caused major fracture on the cutting edge.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: To assess the effects of functional protein on osteoblast, Large quantity of high-purity osteoblasts had been cultivated successfully by adopting sequential enzyme digestion. The growth curve of osteoblasts was protracted by cell counting. Proliferation of osteoblasts was assessed by MTT colorimetry. The experimental results show the functional protein can enhance proliferation, the properties of adhesion and discuss the effect of osteopontin on osteoblast.
Abstract: The high world interest given to the researches concerning the study of moderately halophilic solvent-tolerant bacteria isolated from marine polluted environments is due to their high biotechnological potential, and also to the perspective of their application in different remediation technologies. Using enrichment procedures, I isolated two moderately halophilic Gram-negative bacterial strains from seawater sample, which are tolerant to organic solvents. Cell tolerance, adhesion and cells viability of Aeromonas salmonicida IBBCt2 and Pseudomonas aeruginosa IBBCt3 in the presence of organic solvents depends not only on its physicochemical properties and its concentration, but also on the specific response of the cells, and the cellular response is not the same for these bacterial strains. n-hexane, n-heptane, propylbenzene, with log POW between 3.69 and 4.39, were less toxic for Aeromonas salmonicida IBBCt2 and Pseudomonas aeruginosa IBBCt3, compared with toluene, styrene, xylene isomers and ethylbenzene, with log POW between 2.64 and 3.17. The results indicated that Aeromonas salmonicida IBBCt2 is more susceptible to organic solvents than Pseudomonas aeruginosa IBBCt3. The mechanisms underlying solvent tolerance (e.g., the existance of the efflux pumps) in Aeromonas salmonicida IBBCt2 and Pseudomonas aeruginosa IBBCt3 it was also studied.
Abstract: The aim of the present study was to evaluate the
mucoadhesion and the release of nicotinamide gel formulations using
in vitro methods. An agar plate technique was used to investigate the
adhesiveness of the gels whereas a diffusion apparatus was employed
to determine the release of nicotinamide from the gels. In this
respect, 10% w/w nicotinamide gels containing bioadhesive
polymers: Carbopol 934P (0.5-2% w/w), hydroxypropylmethyl
cellulose (HPMC) (4-10% w/w), sodium carboxymethyl cellulose
(SCMC) (4-6% w/w) and methylcellulose 4000 (MC) (3-5% w/w)
were prepared. The gel formulations had pH values in the range of
7.14 - 8.17, which were considered appropriate to oral mucosa
application. In general, the rank order of pH values appeared to be
SCMC > MC4000 > HPMC > Carbopol 934P. Types and
concentrations of polymers used somewhat affected the
adhesiveness. It was found that anionic polymers (Carbopol 934 and
SCMC) adhered more firmly to the agar plate than the neutral
polymers (HPMC and MC 4000). The formulation containing 0.5%
Carbopol 934P (F1) showed the highest release rate. With the
exception of the formulation F1, the neutral polymers tended to give
higher relate rates than the anionic polymers. For oral tissue
treatment, the optimum has to be balanced between the residence
time (adhesiveness) of the formulations and the release rate of the
drug. The formulations containing the anionic polymers: Carbopol
934P or SCMC possessed suitable physical properties (appearance,
pH and viscosity). In addition, for anionic polymer formulations,
justifiable mucoadhesive properties and reasonable release rates of
nicotinamide were achieved. Accordingly, these gel formulations
may be applied for the treatment of oral mucosal lesions.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.
Abstract: NFκB is a transcription factor regulating many
function of the vessel wall. In the normal condition , NFκB is
revealed diffuse cytoplasmic expressionsuggesting that the system is
inactive. The presence of activation NFκB provide a potential
pathway for the rapid transcriptional of a variety of genes encoding
cytokines, growth factors, adhesion molecules and procoagulatory
factors. It is likely to play an important role in chronic inflamatory
disease involved atherosclerosis. There are many stimuli with the
potential to active NFκB, including hyperlipidemia. We used 24 mice
which was divided in 6 groups. The HFD given by et libitum
procedure during 2, 4, and 6 months. The parameters in this study
were the amount of NFKB activation ,H2O2 as ROS and VCAM-1 as
a product of NFKB activation. H2O2 colorimetryc assay performed
directly using Anti Rat H2O2 ELISA Kit. The NFKB and VCAM-1
detection obtained from aorta mice, measured by ELISA kit and
imunohistochemistry. There was a significant difference activation of
H2O2, NFKB and VCAM-1 level at induce HFD after 2, 4 and 6
months. It suggest that HFD induce ROS formation and increase the
activation of NFKB as one of atherosclerosis marker that caused by
hyperlipidemia as classical atheroschlerosis risk factor.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: The techniques for estimating the adhesive and cohesive strength in high velocity oxy fuel (HVOF) thermal spray coatings have been discussed and compared. The development trend and the last investigation have been studied. We will focus on benefits and limitations of these methods in different process and materials.
Abstract: Biomimicry has many potential benefits as many
technologies found in nature are superior to their man-made
counterparts. As technological device components approach the micro
and nanoscale, surface properties such as surface adhesion and friction
may need to be taken into account. Lowering surface adhesion by
manipulating chemistry alone might no longer be sufficient for such
components and thus physical manipulation may be required.
Adhesion reduction is only one of the many surface functions
displayed by micro/nano-structured cuticles of insects. Here, we
present a mini review of our understanding of insect cuticle structures
and the relationship between the structure dimensions and the
corresponding functional mechanisms. It may be possible to introduce
additional properties to material surfaces (indeed multi-functional
properties) based on the design of natural surfaces.
Abstract: An implant elicits a biological response in the
surrounding tissue which determines the acceptance and long-term
function of the implant. Dental implants have become one of the
main therapy methods in clinic after teeth lose. A successful implant
is in contact with bone and soft tissue represent by fibroblasts. In our
study we focused on the interaction between six different chemically
and physically modified titanium implants (Tis-MALP, Tis-O, Tis-
OA, Tis-OPAAE, Tis-OZ, Tis-OPAE) with alveolar fibroblasts as
well as with five type of microorganisms (S. epidermis, S.mutans, S.
gordonii, S. intermedius, C.albicans). The analysis of microorganism
adhesion was determined by CFU (colony forming unite) and biofilm
formation. The presence of α3β1 and vinculin expression on alveolar
fibroblasts was demonstrated using phospho specific cell based
ELISA (PACE). Alveolar fibroblasts have the highest expression of
these proteins on Tis-OPAAE and Tis-OPAE. It corresponds with
results from bacterial adhesion and biofilm formation and it was
related to the lowest production of collagen I by alveolar fibroblasts
on Tis-OPAAE titanium disc.