Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: The effect of chemical treatment in CdCl2 on the
compositional changes and defect structures of potentially useful ZnS
solar cell thin films prepared by vacuum deposition method was
studied using the complementary Rutherford backscattering (RBS)
and Thermoluminesence (TL) techniques. A series of electron and
hole traps are found in the various as deposited samples studied.
After treatment, perturbation on the intensity is noted; mobile defect
states and charge conversion and/or transfer between defect states are
found.
Abstract: For a determined intermediate band position, the effects of electron filling factor and sunlight concentration on the active region thickness and efficiency of the quantum-dot intermediate band solar cell are calculated. For each value of electron filling factor, the maximum point of efficiency obtained and resulted in the optimum thickness of the cell under three different sunlight concentrations. We show the importance of filling factor as a parameter to be more considered. The photon recycling effect eliminated in all calculations.
Abstract: The renewable energy has been attracting attention as
a new alternative energy due to the problem of environmental
pollution and resource depletion. In particular, daylighting and PV
system are regarded as the solutions. In this paper, the hybrid
dimming control system supplied by solar cell and daylighting
system was designed. Daylighting system is main source and PV
system is spare source. PV system operates the LED lamp which
supports daylighting system because daylighting system is unstable
due to the variation of irradiance. In addition, PV system has a role
charging batteries. Battery charging has a benefit that PV system
operate LED lamp in the bad weather. However, LED lamp always
can`t turn on that-s why dimming control system was designed. In
particular, the solar charging robot was designed to check the
interior irradiance intensity. These systems and the application of
the solar charging robot are expected to contribute developing
alternative energy in the near future.
Abstract: In this paper, four carbazole-based D-D-π-A organic
dyes code as CCT2A, CCT3A, CCT1PA and CCT2PA were reported.
A series of these organic dyes containing identical donor and
acceptor group but different π-system. The effect of replacing of
thiophene by phenyl thiophene as π-system on the physical
properties has been focused. The structural, energetic properties and
absorption spectra were theoretically investigated by means of
Density Functional Theory (DFT) and Time-Dependent Density
Functional Theory (TD-DFT). The results show that nonplanar
conformation due to steric hindrance in donor part (cabazolecarbazole
unit) of dye molecule can prevent unfavorable dye
aggregation. By means of the TD-DFT method, the absorption
spectra were calculated by B3LYP and BHandHLYP to study the
affect of hybrid functional on the excitation energy (Eg). The results
revealed the increasing of thiophene units not only resulted in
decreasing of Eg, but also found the shifting of absorption spectra to
higher wavelength. TD-DFT/BHandHLYP calculated results are
more strongly agreed with the experimental data than B3LYP
functions. Furthermore, the adsorptions of CCT2A and CCT3A on the
TiO2 anatase (101) surface were carried out by mean of the chemical
periodic calculation. The result exhibit the strong adsorption energy.
The calculated results provide our new organic dyes can be
effectively used as dye for Dye Sensitized Solar Cell (DSC).
Abstract: This paper presents an equivalent circuit model based on piecewise linear parallel branches (PLPB) to study solar cell modules which are partially shaded. The PLPB model can easily be used in circuit simulation software such as the ElectroMagnetic Transients Program (EMTP). This PLPB model allows the user to simulate several different configurations of solar cells, the influence of partial shadowing on a single or multiple cells, the influence of the number of solar cells protected by a bypass diode and the effect of the cell connection configuration on partial shadowing.
Abstract: Although White LED lighting systems powered by solar cells have presented for many years, they are not widely used in today application because of their cost and low energy conversion efficiency. The proposed system use the dc power generated by fixed solar cells module to energize White LED light sources that are operated by directly connected White LED with current limitation resistors, resulting in much more power consumption. This paper presents the use of white LED as a general lighting application powered by tracking solar cells module and using pulse to apply the electrical power to the White LED. These systems resulted in high efficiency power conversion, low power consumption, and long light of the white LED.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: This study was carried out experimentally and analytically about the performance of solar cell panel system for operating the pump coupled by dc-motor. The solar cell panel with total area 1.9848 m2 consists of three modules of 80 Wp each. The small centrifugal pump powered by dc-motor is operated to lift water from 1m to 7m heads in sequence and gives the amount of water pumped over the whole day from 08.00 to 16.00 h are 11988, 10851, 8874, 7695, 5760, 3600, 2340 L/d respectively. The hourly global solar radiation during the day is an average of 506 W/m2. This study also presents the I-V characteristics of the panel at global radiations 200, 400, 600, 800 and 1000 W/m2 matched with the operation of the pump at the above lifting heads. It proves that the only solar radiations 800 and 1000 W/m2 could provide lifting head from 1m to 7m. The analysis shows the best efficiency point of the performance of solar cell panel system occurs at the pumping head 2.89 m.
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: A convenient and physically sound mathematical model of the external or I - V characteristic of solar cells generators is presented in this paper. This model is compared with the traditional model of p-n junction. The direct analytical calculation of load regime leads to a quadratic equation, which is importantly to simplify the calculations in the real time.
Abstract: Structural and UV/Visible optical properties can be
useful to describe a material for the CIGS solar cell active layer,
therefore, this work demonstrates the properties like surface
morphology, X-ray Photoelectron Spectroscopy (XPS) bonding
energy (EB) core level spectra, UV/Visible absorption spectra,
refractive index (n), optical energy band (Eg), reflection spectra for
the Cu25 (In16Ga9) Se40Te10 (CIGST-1) and Cu20 (In14Ga9) Se45Te12
(CIGST-2) chalcogenide compositions. Materials have been
exhibited homogenous surface morphologies, broading /-or diffusion
of bonding energy peaks relative elemental values and a high
UV/Visible absorption tendency in the wave length range 400 nm-
850 nm range with the optical energy band gaps 1.37 and 1.42
respectively. Subsequently, UV/Visible reflectivity property in the
wave length range 250 nm to 320 nm for these materials has also
been discussed.
Abstract: We have modeled the effect of a graded band gap
window on the performance of a single junction AlxGa1-xAs/GaAs
solar cell. First, we study the electrical characteristics of a single
junction AlxGa1-xAs/GaAs solar cell, by employing an optimized
structure for this solar cell, we show that grading the band gap of the
window can increase the conversion efficiency of the solar cell by
about 1.5%, and can also improve the quantum efficiency of the solar
cell especially at shorter wavelengths.
Abstract: This paper presents Simulated Annealing based
approach to estimate solar cell model parameters. Single diode solar
cell model is used in this study to validate the proposed approach
outcomes. The developed technique is used to estimate different
model parameters such as generated photocurrent, saturation current,
series resistance, shunt resistance, and ideality factor that govern the
current-voltage relationship of a solar cell. A practical case study is
used to test and verify the consistency of accurately estimating
various parameters of single diode solar cell model. Comparative
study among different parameter estimation techniques is presented
to show the effectiveness of the developed approach.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: The need to implement intelligent highways is much
more emphasized with the growth of vehicle production line as well as vehicle intelligence. The control of intelligent vehicles in order to
reduce human error and boost ease congestion is not accomplished solely by the aid of human resources. The present article is an attempt
to introduce an intelligent control system based on a single central computer. In this project, central computer, without utilizing Global
Positioning System (GPS), is capable of tracking all vehicles, crisis management and control, traffic guidance and recording traffic
crimes along the highway. By the help of RFID technology, vehicles
are connected to computerized systems, intelligent light poles and
other available hardware along the way. By the aid of Wimax
communicative technology, all components of the system are
virtually connected together through local and global networks
devised in them and the energy of the network is provided by the
solar cells installed on the intelligent light poles.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: An empirical linearly-hyperbolic approximation of the I - V characteristic of a solar cell is presented. This approximation is based on hyperbolic dependence of a current of p-n junctions on voltage for large currents. Such empirical approximation is compared with the early proposed formal linearly-hyperbolic approximation of a solar cell. The expressions defining laws of change of parameters of formal approximation at change of a photo current of family of characteristics are received. It allows simplifying a finding of parameters of approximation on actual curves, to specify their values. Analytical calculation of load regime for linearly - hyperbolic model leads to quadratic equation. Also, this model allows to define soundly a deviation from the maximum power regime and to compare efficiency of regimes of solar cells with different parameters.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy