Abstract: Mobile Ad hoc Networks is an autonomous system of
mobile nodes connected by multi-hop wireless links without
centralized infrastructure support. As mobile communication gains
popularity, the need for suitable ad hoc routing protocols will
continue to grow. Efficient dynamic routing is an important research
challenge in such a network. Bandwidth constrained mobile devices
use on-demand approach in their routing protocols because of its
effectiveness and efficiency. Many researchers have conducted
numerous simulations for comparing the performance of these
protocols under varying conditions and constraints. Most of them are
not aware of MAC Protocols, which will impact the relative
performance of routing protocols considered in different network
scenarios. In this paper we investigate the choice of MAC protocols
affects the relative performance of ad hoc routing protocols under
different scenarios. We have evaluated the performance of these
protocols using NS2 simulations. Our results show that the
performance of routing protocols of ad hoc networks will suffer when
run over different MAC Layer protocols.
Abstract: The objective of this paper is to design a model of human vital sign prediction for decreasing prediction error by using two states mapping based time series neural network BP (back-propagation) model. Normally, lot of industries has been applying the neural network model by training them in a supervised manner with the error back-propagation algorithm for time series prediction systems. However, it still has a residual error between real value and prediction output. Therefore, we designed two states of neural network model for compensation of residual error which is possible to use in the prevention of sudden death and metabolic syndrome disease such as hypertension disease and obesity. We found that most of simulations cases were satisfied by the two states mapping based time series prediction model compared to normal BP. In particular, small sample size of times series were more accurate than the standard MLP model. We expect that this algorithm can be available to sudden death prevention and monitoring AGENT system in a ubiquitous homecare environment.
Abstract: Natural ventilation has played an important role for
many low energy-building designs. It has been also noticed as a
essential subject to persistently bring the fresh cool air from the
outside into a building. This study carried out the computational fluid
dynamics (CFD)-based simulations to examine the natural ventilation
development of a work area in a public building. The simulated results
can be useful to better understand the indoor microclimate and the
interaction of wind with buildings. Besides, this CFD simulation
procedure can serve as an effective analysis tool to characterize the
airing performance, and thereby optimize the building ventilation for
strengthening the architects, planners and other decision makers on
improving the natural ventilation design of public buildings.
Abstract: A study of various turbulent inflow generation methods
was performed to compare their relative effectiveness for LES
computations of turbulent boundary layers. This study confirmed
the quality of the turbulent information produced by the family of
recycling and rescaling methods which take information from within
the computational domain. Furthermore, more general inflow methods
also proved applicable to such simulations, with a precursor-like
inflow and a random inflow augmented with forcing planes showing
promising results.
Abstract: This paper focuses on the calibration problem of a
multi-view shooting system designed for the production of 3D
content for auto-stereoscopic visualization. The considered multiview
camera is characterized by coplanar and decentered image
sensors regarding to the corresponding optical axis. Based on the
Faugéras and Toscani-s calibration approach, a calibration method is
herein proposed for the case of multi-view camera with parallel and
decentered image sensors. At first, the geometrical model of the
shooting system is recalled and some industrial prototypes with some
shooting simulations are presented. Next, the development of the
proposed calibration method is detailed. Finally, some simulation
results are presented before ending with some conclusions about this
work.
Abstract: A new class of percolation model in complex networks,
in which nodes are characterized by hidden variables reflecting the
properties of nodes and the occupied probability of each link is
determined by the hidden variables of the end nodes, is studied
in this paper. By the mean field theory, the analytical expressions
for the phase of percolation transition is deduced. It is determined
by the distribution of the hidden variables for the nodes and the
occupied probability between pairs of them. Moreover, the analytical
expressions obtained are checked by means of numerical simulations
on a particular model. Besides, the general model can be applied
to describe and control practical diffusion models, such as disease
diffusion model, scientists cooperation networks, and so on.
Abstract: This paper presents the optimal controller design of
the generator control unit in the aircraft power system. The adaptive
tabu search technique is applied to tune the controller parameters
until the best terminal output voltage of generator is achieved. The
output response from the system with the controllers designed by the
proposed technique is compared with those from the conventional
method. The transient simulations using the commercial software
package show that the controllers designed from the adaptive tabu
search algorithm can provide the better output performance compared
with the result from the classical method. The proposed design
technique is very flexible and useful for electrical aircraft engineers.
Abstract: A macroscopic constitutive equation is developed for a high-density cellulose insulation material with emphasis on the outof- plane stress relaxation behavior. A hypothesis is proposed where the total stress is additively composed by an out-of-plane visco-elastic isotropic contribution and an in-plane elastic orthotropic response. The theory is validated against out-of-plane stress relaxation, compressive experiments and in-plane tensile hysteresis, respectively. For large scale finite element simulations, the presented model provides a balance between simplicity and capturing the materials constitutive behaviour.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: In this paper, we propose a solution to the motion
control problem of a 2-link revolute manipulator arm. We require the
end-effector of the arm to move safely to its designated target in a
priori known workspace cluttered with fixed circular obstacles of
arbitrary position and sizes. Firstly a unique velocity algorithm is
used to move the end-effector to its target. Secondly, for obstacle
avoidance a turning angle is designed, which when incorporated into
the control laws ensures that the entire robot arm avoids any number
of fixed obstacles along its path enroute the target. The control laws
proposed in this paper also ensure that the equilibrium point of the
system is asymptotically stable. Computer simulations of the
proposed technique are presented.
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: This paper mainly proposes an efficient modified
particle swarm optimization (MPSO) method, to identify a slidercrank
mechanism driven by a field-oriented PM synchronous motor.
In system identification, we adopt the MPSO method to find
parameters of the slider-crank mechanism. This new algorithm is
added with “distance" term in the traditional PSO-s fitness function to
avoid converging to a local optimum. It is found that the comparisons
of numerical simulations and experimental results prove that the
MPSO identification method for the slider-crank mechanism is
feasible.
Abstract: Equilibrium and rate based models have been applied
in the simulation of methyl tertiary-butyl ether (MTBE) synthesis
through reactive distillation. Temperature and composition profiles
were compared for both the models and found that both the profiles
trends, though qualitatively similar are significantly different
quantitatively. In the rate based method (RBM), multicomponent
mass transfer coefficients have been incorporated to describe
interphase mass transfer. MTBE mole fraction in the bottom stream is
found to be 0.9914 in the Equilibrium Model (EQM) and only 0.9904
for RBM when the same column configuration was preserved. The
individual tray efficiencies were incorporated in the EQM and
simulations were carried out. Dynamic simulation have been also
carried out for the two column configurations and compared.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: This work has been carried out in order to provide an understanding of the physical behaviors of the flow variation of pressure and temperature in a vortex tube. A computational fluid dynamics model is used to predict the flow fields and the associated temperature separation within a Ranque–Hilsch vortex tube. The CFD model is a steady axisymmetric model (with swirl) that utilizes the standard k-ε turbulence model. The second–order numerical schemes, was used to carry out all the computations. Vortex tube with a circumferential inlet stream and an axial (cold) outlet stream and a circumferential (hot) outlet stream was considered. Performance curves (temperature separation versus cold outlet mass fraction) were obtained for a specific vortex tube with a given inlet mass flow rate. Simulations have been carried out for varying amounts of cold outlet mass flow rates. The model results have a good agreement with experimental data.
Abstract: We developed a non-contact method for the in-situ
monitoring of the thermal forming of glass and Si foils to optimize
the manufacture of mirrors for high-resolution space x-ray
telescopes. Their construction requires precise and light-weight
segmented optics with angular resolution better than 5 arcsec. We
used 75x25 mm Desag D263 glass foils 0.75 mm thick and 0.6 mm
thick Si foils. The glass foils were shaped by free slumping on a
frame at viscosities in the range of 109.3-1012 dPa·s, the Si foils by
forced slumping above 1000°C. Using a Nikon D80 digital camera,
we took snapshots of a foil-s shape every 5 min during its isothermal
heat treatment. The obtained results we can use for computer
simulations. By comparing the measured and simulated data, we can
more precisely define material properties of the foils and optimize
the forming technology.
Abstract: In this paper we present a general formalism for the
establishment of the family of selective regressor affine projection
algorithms (SR-APA). The SR-APA, the SR regularized APA (SR-RAPA),
the SR partial rank algorithm (SR-PRA), the SR binormalized
data reusing least mean squares (SR-BNDR-LMS), and the SR normalized
LMS with orthogonal correction factors (SR-NLMS-OCF)
algorithms are established by this general formalism. We demonstrate
the performance of the presented algorithms through simulations in
acoustic echo cancellation scenario.
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.