Abstract: Ripe ‘Nam Dok Mai’ mango (Mangifera indica L.) is an important exported fruit of Thailand, but rapidly declined in the quality attributes mainly by infection of anthracnose and stem end rot diseases. Multilayer coating is considered as a developed technique to maintain the postharvest quality of mangoes. The utilization of alternated coating by matching oppositely electrostatic charges between 0.1% chitosan and 0.1% polystyrene sulfonate (PSS) was studied. A number of the coating layers (layer by layer) were applied on mature green ‘Nam Dok Mai No.4’ mangoes prior to storage at 25 oC, 65-70% relative humidity (RH). There were significant differences in some quality attributes of mangoes coated by 3½ layers, 4½ layers and 5½ layers. In comparison to coated mangoes, uncoated fruits were higher in weight loss, total soluble solids, respiration rate, ethylene production and disease incidence except the titratable acidity. Coating fruit at 3½ layers exhibited the ripening delay and reducing disease infection without off flavour. On the other hand, fruit coated with 5½ layers comprised the lowest acceptable score, caused by exhibiting disorders from fermentation at the end of storage. As a result, multilayer coating between chitosan and PSS could effectively maintain the postharvest quality of mango, but number of coating layers should be thoroughly considered.
Abstract: To manage the demand of wireless communication that has been dramatically increased, switched beam antenna in smart antenna system is focused. Implementation of switched beam antennas at mobile terminals such as notebook or mobile handset is a preferable choice to increase the performance of the wireless communication systems. This paper proposes the low complexity switched beam antenna using single element of antenna which is suitable to implement at mobile terminal. Main beam direction is switched by changing the positions of short circuit on the radiating patch. There are four cases of switching that provide four different directions of main beam. Moreover, the performance in terms of Signal to Interference Ratio when utilizing the proposed antenna is compared with the one using omni-directional antenna to confirm the performance improvable.
Abstract: The study discusses the effectiveness of health and safety induction practices on construction sites against the background of the Zambian construction industry experience. The research design included the literature review of relevant literature. Questionnaires and interviews were administered to regulatory bodies, health, and safety personnel. Observation was also employed on construction sites to assess the health and safety practices being used. Health and safety in the construction industry are not something to be ignored or overlooked. The construction industry needs to take heed of the serious consequences of inadequate health and safety induction practices. The implications of inadequate health and safety induction procedures included among others threats to profitability, corporate social responsibility and increased turnover of the workforce leading to poor productivity. Adequate health and safety practices can improve the health and wellbeing of employees, reduce financial implications on firms and encourage productivity on construction sites. Despite this, accidents are still prevalent on construction sites in Zambia. The overall result of this research denotes that the implementation of health and safety induction practices is inadequate, as indicated by the negligent and non-adherent attitude to health and safety induction aspects on the sites by most stakeholders on construction sites. Therefore, health and safety induction practices are ineffective as preventive measures for reduction of accidents on construction sites in Zambia.
Abstract: Enzymatic modification of rice flour can produce highly functional derivatives use in food industries. This study aimed to evaluate the physical properties and resistant starch content of rice flour residues hydrolyzed by α-amylase. Rice flour hydrolyzed by α-amylase (60 and 300 u/g) for 1, 24 and 48 hours were investigated. Increasing enzyme concentration and hydrolysis time resulted in decreased rice flour residue’s lightness (L*) but increased redness (a*) and yellowness (b*) of rice flour residues. The resistant starch content and peak viscosity increased when hydrolysis time increased. Pasting temperature, trough viscosity, breakdown, final viscosity, setback and peak time of the hydrolyzed flours were not significantly different (p>0.05). The morphology of native flour was smooth without observable pores and polygonal with sharp angles and edges. However, after hydrolysis, granules with a slightly rough and porous surface were observed and a rough and porous surface was increased with increasing hydrolyzed time. The X-ray diffraction patterns of native flour showed A-type configuration, which hydrolyzed flour showed almost 0% crystallinity indicated that both amorphous and crystalline structures of starch were simultaneously hydrolyzed by α-amylase.
Abstract: Despite the considerable body of literature investigating the influence of National Culture (NC) dimensions on consumer behaviour, there is a lack of studies comparing the influence of NC in Africa with Western European countries. This study is intended to fill the vacuum in knowledge by exploring how NC affects consumer buyer behavior in Nigeria and the United Kingdom. The primary data were collected through in depth, semi-structured interviews conducted with three groups of individuals: British students, Nigerian students in the United Kingdom, and Nigerian-based students. This approach and new frontier to analyze culture and consumer behaviour could help understand residual cultural threads of people (that are ingrained in their being) irrespective of exposure to other cultures. The findings of this study show that Nigerian and British consumers differ remarkably in cultural orientations such as symbols, values and psychological standpoints. This ultimately affects the choices made at every stage of the decision building process, and proves beneficial for international retail marketing.
Abstract: Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.
Abstract: The effects of varying air temperature (full, ¾ full, ½ full aircon adjustment, no aircon) in polishing component of Single-Pass Mill on the quality of Philippine inbred rice variety, was investigated. Parameters measured were milling recovery (MR), headrice recovery (HR), and percentage with bran streaks. Cooling method (with aircon) increased MR, HR, and percentage with bran streaks of milled rice. Highest MR and HR (67.62%; 47.33%) were obtained from ¾ full adjustment whereas no aircon were lowest (66.27%; 39.76%). Temperature in polishing component at ¾ full adjustment was 33oC whereas no aircon was 45oC. There was increase of 1.35% in MR and 7.57% in HR. Additional cost of milling per kg due to aircon cooling was P0.04 at 300 tons/yr volume, with 0.15 yr payback period. Net income was estimated at ₱98,100.00. Percentage of kernels with bran streaks increased from 5%–14%, indicating more nutrients of milled rice.
Abstract: The research work covered in this study includes the morphological structure and optical properties of TiO2-coated silk fibroin (SF) filters at 2.5% wt. TiO2/vol. PVA solution. SEM micrographs revealed the fibrous morphology of the TiO2-coated SF filters. An average diameter of the SF fiber was estimated to be approximately 10µm. Also, it was confirmed that TiO2 can be adhered more on SF filter surface at higher TiO2 dosages. The activity of semiconductor materials was studied by UV-VIS spectrophotometer method. The spectral data recorded shows the strong cut off at 390 nm. The calculated band-gap energy was about 3.19 eV. The photocatalytic activity of the filter was tested for gaseous formaldehyde removal in a modeling room with the total volume of 2.66 m3. The highest removal efficiency (54.72 ± 1.75%) was obtained at the initial formaldehyde concentration of about 5.00 ± 0.50ppm.
Abstract:
This research studied the influence of delta wing and delta winglet vortex generators on air flow characteristic. Normally, the vortex generator has been used for enhancing the heat transfer performance by promote the helical flow of air stream. The vortex generator was setup in the wind tunnel and the flow pattern of air stream passing the vortex generator was observed by using smoke generator. The Reynolds number of air stream was between 30,000 and 80,000. It is found that the delta winglet having 20mm fin height and 30 degree of air stream contact angle generates the maximum helical flow of air stream.
Abstract: The in vitro culture procedure of purple nutsedge
(Cyperus rotundus L.) for multiple shoot induction and tuber
formation was established. Multiple shoots were significantly
induced from a single shoot of about 0.5 – 0.8 cm long, on Murashige
and Skoog (MS) medium supplemented with 4.44 μM 6-
benzyladinine (BA) alone or in combination with 2.85 μM 1-
indoleacetic acid (IAA), providing 17.6 and 15.3 shoots per explant
with 31.2 and 27.5 leaves per explant, respectively, within 6 weeks of
culturing. Moreover, MS medium supplemented with 4.44 μM BA
and 2.85 μM IAA was suitable for tuber induction, obtaining 5.9
tubers with 3.4 rhizomes per explant. In combination with ancymidol
and higher concentration of sucrose, 11.1 μM BA and 60 g/L sucrose
or 11.1 μM BA, 7.8 μM ancymidol and 60 g/L sucrose induced 3.5
tubers with 1.6 rhizomes or 3.5 tubers without rhizome, respectively.
However, MS medium containing 3.9 or 7.8 μM ancymidol in
combination with either 60 or 80 g/L sucrose enchanced significant
root formation at 20.9 – 23.6 roots per explant.
Abstract: Viral influenza A subtypes H5N1 and pandemic
H1N1 (pH1N1) have worldwide emerged and transmitted. The most
common anti-influenza drug for treatment of both seasonal and
pandemic influenza viruses is oseltamivir that nowadays becomes
resistance to influenza neuraminidase. The novel long-acting drug,
laninamivir, was discovered for treatment of the patients infected
with influenza B and influenza A viruses. In the present study,
laninamivir complexed with wild-type strain of both H5N1 and
pH1N1 viruses were comparatively determined the structures and
drug-target interactions by means of molecular dynamics (MD)
simulations. The results show that the hydrogen bonding interactions
formed between laninamivir and its binding residues are likely
similar for the two systems. Additionally, the presence of
intermolecular interactions from laninamivir to the residues in the
binding pocket is established through their side chains in accordance
with hydrogen bond interactions.
Abstract: Agricultural waste is mainly composed of cellulose
and hemicelluloses which can be converted to sugars. The
inexpensive reducing sugar from durian peel was obtained by
hydrolysis with HCl concentration at 0.5-2.0% (v/v). The hydrolysis
range of time was for 15-60 min when the mixture was autoclaved at
121 °C. The result showed that acid hydrolysis efficiency (AHE)
highest to 80.99% at condition is 2.0%concentration for 15 min.
Reducing sugar highest to 56.07 g/litre at condition is 2.0%
concentration for 45min. Total sugar highest to 59.83 g/litre at
condition is 2.0%concentration for 45min, which was not significant
(p < 0.05) with condition 2.0% concentration for 30 min and 1.5 %
concentration for 45 and 60 min. The increase in concentration
increased AHE, reducing sugar and total sugar. The hydrolysis time
had no effect on AHE, reducing sugar and total sugar. The maximum
reducing sugars of each concentration were at hydrolysis time 45
min .The hydrolysated were analysis by HPLC, the results revealed
that the principle of sugar were glucose, fructose and xylose.
Abstract: The main objective of this research is to synthesize silk fibroin fiber for indoor air particulate removal. Silk cocoons were de-gummed using 0.5 wt % Na2CO3 alkaline solutions at 90 Ó╣ìC for 60 mins, washed with distilled water, and dried at 80 Ó╣ìC for 3 hrs in a vacuum oven. Two sets of experiment were conducted to investigate the impacts of initial particulate matter (PM) concentration and that of air flow rate on the removal efficiency. Rice bran collected from a local rice mill in Ubonratchathani province was used as indoor air contaminant in this work. The morphology and physical properties of silk fibroin (SF) fiber were measured. The SEM revealed the deposition of PM on the used fiber. The PM removal efficiencies of 72.29 ± 3.03 % and 39.33 ± 1.99 % were obtained of PM10 and PM2.5, respectively, when using the initial PM concentration at 0.040 mg/m3 and 0.020 mg/m3 of PM10 and PM2.5, respectively, with the air flow rate of 5 L/min.
Abstract: In this paper two models using a functional network
were employed to solving classification problem. Functional networks
are generalized neural networks, which permit the specification of
their initial topology using knowledge about the problem at hand. In
this case, and after analyzing the available data and their relations, we
systematically discuss a numerical analysis method used for
functional network, and apply two functional network models to
solving XOR problem. The XOR problem that cannot be solved with
two-layered neural network can be solved by two-layered functional
network, which reveals a potent computational power of functional
networks, and the performance of the proposed model was validated
using classification problems.
Abstract: The photocatalytic activity efficiency of TiO2 for the degradation of Toluene in photoreactor can be enhanced by nano- TiO2/LDPE composite film. Since the amount of TiO2 affected the efficiency of the photocatalytic activity, this work was mainly concentrated on the effort to embed the high amount of TiO2 in the Polyethylene matrix. The developed photocatalyst was characterized by XRD, UV-Vis spectrophotometer and SEM. The SEM images revealed the high homogeneity of the deposition of TiO2 on the polyethylene matrix. The XRD patterns interpreted that TiO2 embedded in the PE matrix exhibited mainly in anatase form. In addition, the photocatalytic results show that the toluene removal efficiencies of 30±5%, 49±4%, 68±5%, 42±6% and 33±5% were obtained when using the catalyst loading at 0%, 10%, 15%, 25% and 50% (wt. cat./wt. film), respectively.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
when combining the minimum energy and jerk of indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of the minimum energy, the minimum jerk and combining them
together are found using the dynamic optimization methods together
with the numerical approximation. This is to allow us to simulate
and compare visually and statistically the time history of state inputs
employed by combining minimum energy and jerk designs. The
numerical solution of minimum direct jerk and energy problem are
exactly the same solution; however, the solutions from problem of
minimum energy yield the similar solution especially in term of
tendency.
Abstract: In quality control of freeze-dried durian, crispiness is
a key quality index of the product. Generally, crispy testing has to be
done by a destructive method. A nondestructive testing of the
crispiness is required because the samples can be reused for other
kinds of testing. This paper proposed a crispiness classification
method of freeze-dried durians using fuzzy logic for decision
making. The physical changes of a freeze-dried durian include the
pores appearing in the images. Three physical features including (1)
the diameters of pores, (2) the ratio of the pore area and the
remaining area, and (3) the distribution of the pores are considered to
contribute to the crispiness. The fuzzy logic is applied for making the
decision. The experimental results comparing with food expert
opinion showed that the accuracy of the proposed classification
method is 83.33 percent.
Abstract: Every 2-3 years the influenza B virus serves
epidemics. Neuraminidase (NA) is an important target for influenza
drug design. Although, oseltamivir, an oral neuraminidase drug, has
been shown good inhibitory efficiency against wild-type of influenza
B virus, the lower susceptibility to the R152K mutation has been
reported. Better understanding of oseltamivir efficiency and
resistance toward the influenza B NA wild-type and R152K mutant,
respectively, could be useful for rational drug design. Here, two
complex systems of wild-type and R152K NAs with oseltamivir
bound were studied using molecular dynamics (MD) simulations.
Based on 5-ns MD simulation, the loss of notable hydrogen bond and
decrease in per-residue decomposition energy from the mutated
residue K152 contributed to drug compared to those of R152 in wildtype
were found to be a primary source of high-level of oseltamivir
resistance due to the R152K mutation.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: This present paper proposes the modified Elastic Strip
method for mobile robot to avoid obstacles with a real time system in
an uncertain environment. The method deals with the problem of
robot in driving from an initial position to a target position based on
elastic force and potential field force. To avoid the obstacles, the
robot has to modify the trajectory based on signal received from the
sensor system in the sampling times. It was evident that with the
combination of Modification Elastic strip and Pseudomedian filter to
process the nonlinear data from sensor uncertainties in the data
received from the sensor system can be reduced. The simulations and
experiments of these methods were carried out.