Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: Post-anthesis drought stress is the most important
problem affecting wheat production in dryland fields, specially in
Mediterranean regions. The main objective of this research was to
evaluate drought tolerance indices in dryland wheat genotypes under
post-anthesis drought stress. The research was including two different
experiments. In each experiment, twenty dryland bread wheat
genotypes were sown in a randomized complete blocks design
(RCBD) with three replications. One of experiments belonged to
rain-fed conditions (post-anthesis drought stress) and other
experiment was under non-stress conditions (with supplemental
irrigation). Different drought tolerance indices include Stress
Tolerance (Tol), Mean Productivity (MP), Geometric Mean
Productivity (GMP), Stress Susceptibility Index (SSI), Stress
Tolerance Index (STI), Harmonic Mean (HAM), Yield Index (YI)
and Yield Stability Index (YSI) were evaluate based on grain yield
under rain-fed (Ys) and supplemental irrigation (Yp) environments.
G10 and G12 were the most tolerant genotypes based on TOL and
SSI. But, based on MP, GMP, STI, HAM and YI indices, G1 and G2
were selected. STI, GMP and MP indices had high correlation with
grain yield under rain-fed and supplementary irrigation conditions
and were recognized as appropriate indices to identify genotypes with
high grain yield and low sensitivity to drought stress environments.
Abstract: For cognitive radio networks, there is a major
spectrum sensing problem, i.e. dynamic spectrum management. It is
an important issue to sense and identify the spectrum holes in
cognitive radio networks. The first-order derivative scheme is usually
used to detect the edge of the spectrum. In this paper, a novel
spectrum sensing technique for cognitive radio is presented. The
proposed algorithm offers efficient edge detection. Then, simulation
results show the performance of the first-order derivative scheme and
the proposed scheme and depict that the proposed scheme obtains
better performance than does the first-order derivative scheme.
Abstract: The Tropical Data Hub (TDH) is a virtual research environment that provides researchers with an e-research infrastructure to congregate significant tropical data sets for data reuse, integration, searching, and correlation. However, researchers often require data and metadata synthesis across disciplines for crossdomain analyses and knowledge discovery. A triplestore offers a semantic layer to achieve a more intelligent method of search to support the synthesis requirements by automating latent linkages in the data and metadata. Presently, the benchmarks to aid the decision of which triplestore is best suited for use in an application environment like the TDH are limited to performance. This paper describes a new evaluation tool developed to analyze both features and performance. The tool comprises a weighted decision matrix to evaluate the interoperability, functionality, performance, and support availability of a range of integrated and native triplestores to rank them according to requirements of the TDH.
Abstract: High Power Lasers produce an intense burst of
Bremmstrahlung radiation which has potential applications in broadband
x-ray radiography. Since the radiation produced is through the
interaction of accelerated electrons with the remaining laser target,
these bursts are extremely short – in the region of a few ps. As a
result, the laser-produced x-rays are capable of imaging complex
dynamic objects with zero motion blur.
Abstract: Raw wood vinegar was purified by both standing and
filtering methods. Toxicity tests were conducted under laboratory
conditions by the topical application method (contact poison) and
feeding method (stomach poison). Larvicidal activities of wood
vinegar at four different concentrations (10, 15, 20, 25 and 30 %)
were studied against second instar larvae of housefly (Musca
domestica L.). Four replicates were maintained for all treatments and
controls. Larval mortality was recorded up to 96 hours and compared
with the larval survivability by two methods of larvicidal bioassay.
Percent pupation and percent adult emergence were observed in
treated M. domestica. The study revealed that the feeding method
gave higher efficiency compared with the topical application method.
Larval mortality increased with increasing concentration of wood
vinegar and the duration of exposure. No mortality was found in
treated M. domestica larvae at minimum 10% concentration of wood
vinegar through the experiments. The treated larvae were maintained
up to pupa and adult emergence. At 30% maximum concentration
larval duration was extended to 11 days in M. domestica for topical
application method and 9 days for feeding method. Similarly the
pupal durations were also increased with increased concentrations
(16 and 24 days for topical application method and feeding method
respectively at 30% concentration) of the treatments.
Abstract: We assert here that there might be some factors that
influence professional identity construction at the university/higher
education stage. In accord, we propose a conceptual framework of
intervening factors in professional identity construction at university
from a literature review and preliminary data from a qualitative pilot
study using focus groups. This model identifies several factors that
might influence university students- professional identity
construction and group them into categories. In turn, we describe
how these factors might contribute in strengthening or weakening
their professional identity. Finally, we discuss the implications of
strengthening students- PI for the university, individuals and
organizations and we provide a roadmap for future empirical work in
this area.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: Optimal routing in communication networks is a
major issue to be solved. In this paper, the application of Tabu Search
(TS) in the optimum routing problem where the aim is to minimize
the computational time and improvement of quality of the solution in
the communication have been addressed. The goal is to minimize the
average delays in the communication. The effectiveness of Tabu
Search method is shown by the results of simulation to solve the
shortest path problem. Through this approach computational cost can
be reduced.
Abstract: This paper presents the climatic range calculations for
comfort evaporative cooling for Tehran. In this study the minimum
climatic conditions required to achieve an appropriate comfort zone
will be presented.
Physiologically uncomfortable conditions in arid climates are
mainly caused by the extreme heat and dryness. Direct evaporative
cooling adds moisture to the air stream until the air stream is close to
saturation. The dry bulb temperature is reduced, while the wet bulb
temperature stays the same. Evaporative cooling is economical,
effective, environmentally friendly, and healthy.
Comfort cooling by direct evaporative cooling (passive or fan
forced) in the 35. 41 N (such as Tehran) latitude requires design
wet-bulb temperature not over 25.4 C. Evaporative cooling outside
this limit cannot achieve the required 26.7 ET, and is recommended
for relief cooling only.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: This paper presents the impact study of apparent
reactance injected by series Flexible AC Transmission System
(FACTS) i.e. Thyristor Controlled Series Reactor (TCSR) on the
measured impedance of a 400 kV single electrical transmission line
in the presence of phase to earth fault with fault resistance. The study
deals with an electrical transmission line of Eastern Algerian
transmission networks at Group Sonelgaz (Algerian Company of
Electrical and Gas) compensated by TCSR connected at midpoint of
the line. This compensator used to inject active and reactive powers
is controlled by three TCSR-s. The simulations results investigate the
impacts of the TCSR on the parameters of short circuit calculation
and parameters of measured impedance by distance relay in the
presence of earth fault for three cases study.
Abstract: The paper presents the Romanian realities and perspectives from the point of view of reaching the sustainable development model in the context of the recent accession to the European Union, based on the analysis of the indicators listed in the EU Sustainable Development Strategy. The analysis of the economic-social potential for sustainable development and of the environment aspects show that the objectives stipulated in the renewed EU Sustainable Development Strategy of 2006 can be reached, but an extra effort must be put-in in order to overcome the existing substantial gaps in several areas in relation to the developed countries of the EU. The paper-s conclusions show that even if sustainable development is not an easy target to reach in Romania, there are resources and a growing potential, which can lead to sustainable development if used rationally.
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: Active research is underway on virtual touch screens
that complement the physical limitations of conventional touch
screens. This paper discusses a virtual touch screen that uses a
multi-layer perceptron to recognize and control three-dimensional
(3D) depth information from a time of flight (TOF) camera. This
system extracts an object-s area from the image input and compares it
with the trajectory of the object, which is learned in advance, to
recognize gestures. The system enables the maneuvering of content in
virtual space by utilizing human actions.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: Operating rooms are important assets for hospitals as
they generate the largest revenue and, at the same time, produce the
largest cost for hospitals. The model presented in this paper helps
make capacity planning decisions on the combination of open
operating rooms (ORs) and estimated overtime to satisfy the
allocated OR time to each specialty. The model combines both
decisions on determining the amount of OR time to open and to
allocate to different surgical specialties. The decisions made are
based on OR costs, overutilization and underutilization costs, and
contribution margins from allocating OR time. The results show the
importance of having a good estimate of specialty usage of OR time
to determine the amount of needed capacity and highlighted the
tradeoff that the OR manager faces between opening more ORs
versus extending the working time of the ORs already in use.
Abstract: This study aimed to develop and initially validate an instrument that measures social competency among tertiary level faculty members. A review of extant literature on social competence was done. The review of extant literature led to the writing of the items in the initial instrument which was evaluated by 11 Subject Matter Experts (SMEs). The SMEs were either educators or psychologists. The results of the evaluations done by the SMEs served as bases for the creation of the pre-try-out instrument used in the first trial-run. Insights from the first trial-run participants led to the development of the main try-out instrument used in the final test administration. One Hundred Forty-one participants from five private Higher Education Institutions (HEIs) in the National Capital Region (NCR) and five private HEIs in Central Luzon in the Philippines participated in the final test administration. The reliability of the instrument was evaluated using Cronbach-s Coefficient Alpha formula and had a Cronbach-s Alpha of 0.92. On the other hand, Factor Analysis was used to evaluate the validity of the instrument and six factors were identified. The development of the final instrument was based on the results of the evaluation of the instrument-s reliability and validity. For purposes of recognition, the instrument was named “Social Competency Inventory for Tertiary Level Faculty Members (SCI-TLFM)."
Abstract: Polymeric microreactors have emerged as a new
generation of carriers that hold tremendous promise in the areas of
cancer therapy, controlled delivery of drugs, for removal of
pollutants etc. Present work reports a simple and convenient
methodology for synthesis of polystyrene and poly caprolactone
microreactors. An aqueous suspension of carboxylated (1μm)
polystyrene latex particles was mixed with toluene solution followed
by freezing with liquid nitrogen. Freezed particles were incubated at
-20°C and characterized for formation of voids on the surface of
polymer microspheres by Field Emission Scanning Electron
Microscope. The hollow particles were then overnight incubated at
40ºC with unfunctionalized quantum dots (QDs) in 5:1 ratio. QDs
Encapsulated polystyrene microcapsules were characterized by
fluorescence microscopy.
Likewise Poly ε-caprolactone microreactors were prepared by
micro-volcanic rupture of freeze dried microspheres synthesized
using emulsification of polymer with aqueous Poly vinyl alcohol and
freezed with liquid nitrogen. Microreactors were examined with Field
Emission Scanning Electron Microscope for size and morphology.
Current study is an attempt to create hollow polymer particles which
can be employed for microencapsulation of nanoparticles and drug
molecules.