Abstract: This paper presents the comparison ageing deterioration of silicone rubber housing material for outdoor polymer insulators by using salt fog ageing test based on IEC 61109 and outdoor exposure test.Four types of high temperature silicone vulcanized silicone rubber sheet with different amount of ATH were used as testing specimen. For salt fog ageing test, the specimens were tested continuously 1000 hours with energized in test chamber. For outdoor exposure test, the specimens were hung continuously 18 months without energized. Physical and chemical analyses were conducted to evaluate degree of ageing deterioration of tested specimens. Slightly surface erosion was observed on specimen surface after salt fog ageing test and no erosion was observed on surface of outdoor exposure specimen. However, comparable degree of ageing deterioration can be seen from surface analysis results.
Abstract: Numerical analysis for the aerodynamic characteristics
of the WIG (wing-in ground effect) craft with highly cambered and
aspect ratio of one is performed to predict the ground effect for the
case of with- and without- lower-extension endplate. The analysis is
included varying angles of attack from 0 to10 deg. and ground
clearances from 5% of chord to 50%. Due to the ground effect, the lift
by rising in pressure on the lower surface is increased and the
influence of wing-tip vortices is decreased. These two significant
effects improve the lift-drag ratio. On the other hand, the endplate
prevents the high-pressure air escaping from the air cushion at the
wing tip and causes to increase the lift and lift-drag ratio further. It is
found from the visualization of computation results that two wing-tip
vortices are generated from each surface of the wing tip and their
strength are weak and diminished rapidly. Irodov-s criteria are also
evaluated to investigate the static height stability. The comparison of
Irodov-s criteria shows that the endplate improves the deviation of the
static height stability with respect to pitch angles and heights. As the
results, the endplate can improve the aerodynamic characteristics and
static height stability of wings in ground effect, simultaneously.
Abstract: In order to evaluation the effects of soil organic
matter and biofertilizer on chickpea quality and biological
nitrogen fixation, field experiments were carried out in 2007
and 2008 growing seasons. In this research the effects of
different strategies for soil fertilization were investigated on
grain yield and yield component, minerals, organic compounds
and cooking time of chickpea. Experimental units were
arranged in split-split plots based on randomized complete
blocks with three replications. Main plots consisted of (G1):
establishing a mixed vegetation of Vicia panunica and
Hordeum vulgare and (G2): control, as green manure levels.
Also, five strategies for obtaining the base fertilizer
requirement including (N1): 20 t.ha-1 farmyard manure; (N2):
10 t.ha-1 compost; (N3): 75 kg.ha-1 triple super phosphate;
(N4): 10 t.ha-1 farmyard manure + 5 t.ha-1 compost and (N5):
10 t.ha-1 farmyard manure + 5 t.ha-1 compost + 50 kg.ha-1
triple super phosphate were considered in sub plots.
Furthermoree four levels of biofertilizers consisted of (B1):
Bacillus lentus + Pseudomonas putida; (B2): Trichoderma
harzianum; (B3): Bacillus lentus + Pseudomonas putida +
Trichoderma harzianum; and (B4): control (without
biofertilizers) were arranged in sub-sub plots. Results showed
that integrating biofertilizers (B3) and green manure (G1)
produced the highest grain yield. The highest amounts of yield
were obtained in G1×N5 interaction. Comparison of all 2-way
and 3-way interactions showed that G1N5B3 was determined
as the superior treatment. Significant increasing of N, P2O5,
K2O, Fe and Mg content in leaves and grains emphasized on
superiority of mentioned treatment because each one of these
nutrients has an approved role in chlorophyll synthesis and
photosynthesis abilities of the crops. The combined application
of compost, farmyard manure and chemical phosphorus (N5)
in addition to having the highest yield, had the best grain
quality due to high protein, starch and total sugar contents, low
crude fiber and reduced cooking time.
Abstract: In this paper, we consider the problem of logic simplification for a special class of logic functions, namely complementary Boolean functions (CBF), targeting low power implementation using static CMOS logic style. The functions are uniquely characterized by the presence of terms, where for a canonical binary 2-tuple, D(mj) ∪ D(mk) = { } and therefore, we have | D(mj) ∪ D(mk) | = 0 [19]. Similarly, D(Mj) ∪ D(Mk) = { } and hence | D(Mj) ∪ D(Mk) | = 0. Here, 'mk' and 'Mk' represent a minterm and maxterm respectively. We compare the circuits minimized with our proposed method with those corresponding to factored Reed-Muller (f-RM) form, factored Pseudo Kronecker Reed-Muller (f-PKRM) form, and factored Generalized Reed-Muller (f-GRM) form. We have opted for algebraic factorization of the Reed-Muller (RM) form and its different variants, using the factorization rules of [1], as it is simple and requires much less CPU execution time compared to Boolean factorization operations. This technique has enabled us to greatly reduce the literal count as well as the gate count needed for such RM realizations, which are generally prone to consuming more cells and subsequently more power consumption. However, this leads to a drawback in terms of the design-for-test attribute associated with the various RM forms. Though we still preserve the definition of those forms viz. realizing such functionality with only select types of logic gates (AND gate and XOR gate), the structural integrity of the logic levels is not preserved. This would consequently alter the testability properties of such circuits i.e. it may increase/decrease/maintain the same number of test input vectors needed for their exhaustive testability, subsequently affecting their generalized test vector computation. We do not consider the issue of design-for-testability here, but, instead focus on the power consumption of the final logic implementation, after realization with a conventional CMOS process technology (0.35 micron TSMC process). The quality of the resulting circuits evaluated on the basis of an established cost metric viz., power consumption, demonstrate average savings by 26.79% for the samples considered in this work, besides reduction in number of gates and input literals by 39.66% and 12.98% respectively, in comparison with other factored RM forms.
Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.
Abstract: The precision of heat flux simulation influences the
temperature field and test aberration for TB test and also reflects the
test level for spacecraft development. This paper describes TB tests for
a small satellite using solar simulator, electric heaters, calrod heaters
to evaluate the difference of the three methods. Under the same
boundary condition, calrod heaters cases were about 6oC higher than
solar simulator cases and electric heaters cases for
non-external-heat-flux cases (extreme low temperature cases). While
calrod heaters cases and electric heaters cases were 5~7oC and 2~3oC
lower than solar simulator cases respectively for high temperature
cases. The results show that the solar simulator is better than calrod
heaters for its better collimation, non-homogeneity and stability.
Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: To evaluate the ability to predict xerostomia after
radiotherapy, we constructed and compared neural network and
logistic regression models. In this study, 61 patients who completed a
questionnaire about their quality of life (QoL) before and after a full
course of radiation therapy were included. Based on this questionnaire,
some statistical data about the condition of the patients’ salivary
glands were obtained, and these subjects were included as the inputs of
the neural network and logistic regression models in order to predict
the probability of xerostomia. Seven variables were then selected from
the statistical data according to Cramer’s V and point-biserial
correlation values and were trained by each model to obtain the
respective outputs which were 0.88 and 0.89 for AUC, 9.20 and 7.65
for SSE, and 13.7% and 19.0% for MAPE, respectively. These
parameters demonstrate that both neural network and logistic
regression methods are effective for predicting conditions of parotid
glands.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: This paper suggests an improved integer frequency
offset (IFO) estimation scheme using P1 symbol for orthogonal
frequency division multiplexing (OFDM) based the second generation
terrestrial digital video broadcasting (DVB-T2) system. Proposed
IFO estimator is designed by a low-complexity blind IFO estimation
scheme, which is implemented with complex additions. Also, we
propose active carriers (ACs) selection scheme in order to prevent
performance degradation in blind IFO estimation. The simulation
results show that under the AWGN and TU6 channels, the proposed
method has low complexity than conventional method and almost
similar performance in comparison with the conventional method.
Abstract: PPX(Pretty Printer for XML) is a query language that offers a concise description method of formatting the XML data into HTML. In this paper, we propose a simple specification of formatting method that is a combination description of automatic layout operators and variables in the layout expression of the GENERATE clause of PPX. This method can automatically format irregular XML data included in a part of XML with layout decision rule that is referred to DTD. In the experiment, a quick comparison shows that PPX requires far less description compared to XSLT or XQuery programs doing same tasks.
Abstract: Many footbridges have natural frequencies that
coincide with the dominant frequencies of the pedestrian-induced
load and therefore they have a potential to suffer excessive vibrations
under dynamic loads induced by pedestrians. Some of the design
standards introduce load models for pedestrian loads applicable for
simple structures. Load modeling for more complex structures, on the
other hand, is most often left to the designer. The main focus of this
paper is on the human induced forces transmitted to a footbridge and
on the ways these loads can be modeled to be used in the dynamic
design of footbridges. Also design criteria and load models proposed
by widely used standards were introduced and a comparison was
made. The dynamic analysis of the suspension bridge in Kolin in the
Czech Republic was performed on detailed FEM model using the
ANSYS program system. An attempt to model the load imposed by a
single person and a crowd of pedestrians resulted in displacements
and accelerations that are compared with serviceability criteria.
Abstract: In this investigation, types of commercial and special
polyacrylonitrile (PAN) fibers contain sodium 2-methyl-2-
acrylamidopropane sulfonate (SAMPS) and itaconic acid (IA)
comonomers were studied by fourier transform infrared (FT-IR)
spectroscopy. The study of FT-IR spectra of PAN fibers samples
with different comonomers shows that during stabilization of PAN
fibers, the peaks related to C≡N bonds and CH2 are reduced sharply.
These reductions are related to cyclization of nitrile groups and
stabilization procedure. This reduction in PAN fibers contain IA
comonomer is very intense in comparison with PAN fibers contain
SAMPS comonomer. This fact indicates the cycling and stabilization
for sample contain IA comonomer have been conducted more
completely. Therefore the carbon fibers produced from this material
have higher tensile strength due to suitable stabilization.
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Abstract: In this paper we present a method for gene ranking
from DNA microarray data. More precisely, we calculate the correlation
networks, which are unweighted and undirected graphs, from
microarray data of cervical cancer whereas each network represents
a tissue of a certain tumor stage and each node in the network
represents a gene. From these networks we extract one tree for
each gene by a local decomposition of the correlation network. The
interpretation of a tree is that it represents the n-nearest neighbor
genes on the n-th level of a tree, measured by the Dijkstra distance,
and, hence, gives the local embedding of a gene within the correlation
network. For the obtained trees we measure the pairwise similarity
between trees rooted by the same gene from normal to cancerous
tissues. This evaluates the modification of the tree topology due to
progression of the tumor. Finally, we rank the obtained similarity
values from all tissue comparisons and select the top ranked genes.
For these genes the local neighborhood in the correlation networks
changes most between normal and cancerous tissues. As a result
we find that the top ranked genes are candidates suspected to be
involved in tumor growth and, hence, indicates that our method
captures essential information from the underlying DNA microarray
data of cervical cancer.
Abstract: In this article, a method has been offered to classify
normal and defective tiles using wavelet transform and artificial
neural networks. The proposed algorithm calculates max and min
medians as well as the standard deviation and average of detail
images obtained from wavelet filters, then comes by feature vectors
and attempts to classify the given tile using a Perceptron neural
network with a single hidden layer. In this study along with the
proposal of using median of optimum points as the basic feature and
its comparison with the rest of the statistical features in the wavelet
field, the relational advantages of Haar wavelet is investigated. This
method has been experimented on a number of various tile designs
and in average, it has been valid for over 90% of the cases. Amongst
the other advantages, high speed and low calculating load are
prominent.
Abstract: Web usage mining has become a popular research
area, as a huge amount of data is available online. These data can be
used for several purposes, such as web personalization, web structure
enhancement, web navigation prediction etc. However, the raw log
files are not directly usable; they have to be preprocessed in order to
transform them into a suitable format for different data mining tasks.
One of the key issues in the preprocessing phase is to identify web
users. Identifying users based on web log files is not a
straightforward problem, thus various methods have been developed.
There are several difficulties that have to be overcome, such as client
side caching, changing and shared IP addresses and so on. This paper
presents three different methods for identifying web users. Two of
them are the most commonly used methods in web log mining
systems, whereas the third on is our novel approach that uses a
complex cookie-based method to identify web users. Furthermore we
also take steps towards identifying the individuals behind the
impersonal web users. To demonstrate the efficiency of the new
method we developed an implementation called Web Activity
Tracking (WAT) system that aims at a more precise distinction of
web users based on log data. We present some statistical analysis
created by the WAT on real data about the behavior of the Hungarian
web users and a comprehensive analysis and comparison of the three
methods
Abstract: Arc welding creates a weld pool to realize continuity between pieces of assembly. The thermal history of the weld is dependent on heat transfer and fluid flow in the weld pool. The metallurgical transformation during welding and cooling are modeled in the literature only at solid state neglecting the fluid flow. In the present paper we associate a heat transfer – fluid flow and metallurgical model for the 16MnD5 steel. The metallurgical transformation model is based on Leblond model for the diffusion kinetics and on the Koistinen-Marburger equation for Marteniste transformation. The predicted thermal history and metallurgical transformations are compared to a simulation without fluid phase. This comparison shows the great importance of the fluid flow modeling.
Abstract: Understanding the consumption and production of
various metabolites of fibroblast conditioned media is needed for its
proper and optimized use in expansion of pluripotent stem cells. For
this purpose, we have used the HPLC method to analyse the
consumption of glucose and the production of lactate over time by
mouse embryonic fibroblasts. The experimental data have also been
compared with mathematical model fits. 0.025 moles of lactate was
produced after 72 hrs while the glucose concentration decreased from
0.017 moles to 0.011 moles. The mathematical model was able to
predict the trends of glucose consumption and lactate production.