Abstract: The phytotoxicity of heavy metals can be expressed
on roots and visible part of plants and is characterized by molecular
and metabolic answers at various levels of organization of the whole
plant. The present study was undertaken on two varieties of broad
bean Vicia faba (Sidi Aïch and Super Aguadulce). The device was
mounted on a substrate prepared by mixing sand, soil and compost,
the substrate was artificially contaminated with three doses of lead
nitrate [Pb(NO3)2] 0, 500 and 1000 ppm. Our objective is to follow
the behavior of plant opposite the stress by evaluating the
physiological parameters. The results reveal a reduction in the
parameters of the productivity (chlorophyll and proteins production)
with an increase in the osmoregulators (soluble sugars and
proline).These results show that the production of broad bean is
strongly modified by the disturbance of its internal physiology under
lead exposure.
Abstract: The synthesis of CuFe2O4 spinel powders by an
optimized combustion-like process followed by calcination is
described herein. The samples were characterized using X-ray
diffraction (XRD), differential thermal analysis (TG/DTA), scanning
electron microscopy (SEM), dilatometry and 4-probe DC methods.
Different glycine to nitrate (G/N) ratios of 1 (fuel-deficient), 1.48
(stoichiometric) and 2 (fuel-rich) were employed. Calcining the asprepared
powders at 800 and 1000°C for 5 hours showed that the G/N
ratio of 2 results in the formation of the desired copper spinel single
phase at both calcination temperatures. For G/N=1, formation of
CuFe2O4 takes place in three steps. First, iron and copper nitrates
decompose to iron oxide and pure copper. Then, copper transforms to
copper oxide and finally, copper and iron oxides react with each other
to form a copper ferrite spinel phase. The electrical conductivity and
the coefficient of thermal expansion of the sintered pelletized
samples were 2 S.cm-1 (800°C) and 11×10-6 °C-1 (25-800°C),
respectively.
Abstract: Biodiesel production from vegetable oil will produce
glycerol as by-product about 10% of the biodiesel production. The
amount of glycerol that was produced needed alternative way to
handling immediately so as to not become the waste that polluted
environment. One of the solutions was to process glycerol to
polyglycidyl nitrate (PGN). PGN is synthesized from glycerol by
three-step reactions i.e. nitration of glycerol, cyclization of 13-
dinitroglycerine and polymerization of glycosyl nitrate. Optimum
condition of nitration of glycerol with nitric acid has not been known.
Thermodynamic feasibility should be done before run experiments in
the laboratory. The aim of this study was to determine the parameters
those affect nitration of glycerol and nitric acid and chose the
operation condition. Many parameters were simulated to verify its
possibility to experiment under conditions which would get the
highest conversion of 1, 3-dinitroglycerine and which was the ideal
condition to get it. The parameters that need to be studied to obtain
the highest conversion of 1, 3-dinitroglycerine were mol ratio of
nitric acid/glycerol, reaction temperature, mol ratio of
glycerol/dichloromethane and pressure. The highest conversion was
obtained in the range of mol ratio of nitric acid /glycerol between 2/1
– 5/1, reaction temperature of 5-25oC and pressure of 1 atm. The
parameters that need to be studied further to obtain the highest
conversion of 1.3 DNG are mol ratio of nitric acid/glycerol and
reaction temperature.
Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: A pilot field study was conducted at the Jagjeetpur
Municipal Sewage treatment plant situated in the Haridwar town in
Uttarakhand state, India. The objectives of the present study were to
study the effect of treated wastewater on the production of various
paddy varieties (Sharbati, PR-114, PB-1, Menaka, PB1121 and PB
1509) and the emission of GHG gases (CO2, CH4 and N2O) as
compared to the same varieties grown in the control plots irrigated
with fresh water. Of late, the concept of water footprint assessment
has emerged, which explains enumeration of various types of water
footprints of an agricultural entity from its production to processing
stages. Paddy, the most water demanding staple crop of Uttarakhand
state, displayed a high green water footprint value of 2474.12 m3/
Ton. Most of the wastewater irrigated varieties displayed up to 6%
increase in production, except Menaka and PB-1121, which showed a
reduction in production (6% and 3% respectively), due to pest and
insect infestation. The treated wastewater was observed to be rich in
Nitrogen (55.94 mg/ml Nitrate), Phosphorus (54.24 mg/ml) and
Potassium (9.78 mg/ml), thus rejuvenating the soil quality and not
requiring any external nutritional supplements. A Percentage increase
of GHG gases of irrigation with treated municipal wastewater as
compared to control plots was observed as 0.4% - 8.6% (CH4), 1.1%
- 9.2% (CO2), and 0.07% - 5.8% (N2O). The variety, Sharbati,
displayed maximum production (5.5 ton/ha) and emerged as the most
resistant variety against pests and insects. The emission values of
CH4, CO2 and N2O were 729.31 mg/m2/d, 322.10 mg/m2/d and
400.21 mg/m2/d in water stagnant condition.
This study highlighted a successful possibility of reuse of
wastewater for non-potable purposes offering the potential for
exploiting this resource that can replace or reduce the existing use of
fresh water sources in agriculture sector.
Abstract: Nowadays, the main goal for modern horticultural
production is an increase the quality. In recent years, the use of
organic fertilizers or biostimulants that can be applied in agriculture
to improve quali-quantitative crop yields has encountered increasing
interest. Biostimulants are gaining importance also for their possible
use in organic and sustainable agriculture, to avoid excessive
fertilizer applications. Consecutive experimental trials were carried
out in the Apulia region (southern Italy) on three herbaceous crops
(cauliflower, pepper, fennel) grown in pots under conventional and
organic fertilization systems without and with biostimulants. The aim
was to determine the effects of three biostimulants (Siapton®10L,
Micotech L, Lysodin Alga-Fert) on quali-quantitative yield
characteristics. At harvest, the quali-quantitative yield characteristics
of each crop were determined. All of the experimental data were
subjected to analysis of variance (ANOVA), and when significant
effects were detected, the means were compared using Tukey’s tests.
These data show large differences in these yield characteristics
between conventional and organic crops, particularly highlighting
higher yields for the conventional crops, while variable results were
generally observed when the biostimulants were applied. In this
context, there were no effects of the biostimulants on the quantitative
yield, whereas there were low positive effects on the qualitative
characteristics, as related to higher dry matter content of cauliflower,
and higher soluble solids content of pepper. Moreover, there were
evident positive effects of the biostimulants with fennel, due to the
lower nitrate content. These latter data are in line with most of the
published literature obtained for other herbaceous crops.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: Potassium borates, which are widely used in welding
and metal refining industry, as a lubricating oil additive, cement
additive, fiberglass additive and insulation compound, are one of the
important groups of borate minerals. In this study the production of a
potassium borate mineral via hydrothermal method is aimed. The
potassium source of potassium nitrate (KNO3) was used along with a
sodium source of sodium hydroxide (NaOH) and boron source of
boric acid (H3BO3). The constant parameters of reaction temperature
and reaction time were determined as 80°C and 1 h, respectively. The
molar ratios of 1:1:3 (as KNO3:NaOH:H3BO3), 1:1:4, 1:1:5, 1:1:6
and 1:1:7 were used. Following the synthesis the identifications of
the produced products were conducted by X-Ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FT-IR) and Raman
Spectroscopy. The results of the experiments and analysis showed in
the ratio of 1:1:6, the Santite mineral with powder diffraction file
number (pdf no.) of 01-072-1688, which is known as potassium
pentaborate (KB5O8·4H2O) was synthesized as best.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: The development of active and stable catalysts
without noble metals for low temperature oxidation of exhaust gases
remains a significant challenge. The purpose of this study is to
determine the influence of the preparation method on the catalytic
activity of the supported copper-manganese mixed oxides in terms of
VOCs oxidation. The catalysts were prepared by impregnation of γ-
Al2O3 with copper and manganese nitrates and acetates and the
possibilities for CO, CH3OH and dimethyl ether (DME) oxidation
were evaluated using continuous flow equipment with a four-channel
isothermal stainless steel reactor. Effect of the support, Cu/Mn mole
ratio, heat treatment of the precursor and active component loading
were investigated. Highly active alumina supported Cu-Mn catalysts
for CO and VOCs oxidation were synthesized. The effect of
preparation conditions on the activity behavior of the catalysts was
discussed.
The synergetic interaction between copper and manganese species
increases the activity for complete oxidation over mixed catalysts.
Type of support, calcination temperature and active component
loading along with catalyst composition are important factors,
determining catalytic activity. Cu/Mn molar ratio of 1:5, heat
treatment at 450oC and 20 % active component loading are the best
compromise for production of active catalyst for simultaneous
combustion of CO, CH3OH and DME.
Abstract: Background: The objectives of this study were to
assess patient’s knowledge of appropriate sublingual glyceryl
trinitrate (GTN) use as well as to investigate how patients commonly
store and carry their sublingual GTN tablets. Methodology: This was
a cross-sectional survey, using a validated researcher-administered
questionnaire. The study involved cardiac patients receiving
sublingual GTN attending the outpatient and inpatient departments of
Taiping Hospital, a non-academic public care hospital. The minimum
calculated sample size was 92, but 100 patients were conveniently
sampled. Respondents were interviewed on 3 areas, including
demographic data, knowledge and use of sublingual GTN. Eight
items were used to calculate each subject’s knowledge score and six
items were used to calculate use score. Results: Of the 96 patients
who consented to participate, majority (96.9%) were well aware of
the indication of sublingual GTN. With regards to the mechanism of
action of sublingual GTN, 73 (76%) patients did not know how the
medication works. Majority of the patients (66.7%) knew about the
proper storage of the tablet. In relation to the maximum number of
sublingual GTN tablets that can be taken during each angina episode,
36.5% did not know that up to 3 tablets of sublingual GTN can be
taken during each episode of angina. Fifty four (56.2%) patients were
not aware that they need to replace sublingual GTN every 8 weeks
after receiving the tablets. Majority (69.8%) of the patients
demonstrated lack of knowledge with regards to the use of sublingual
GTN as prevention of chest pain. Conclusion: Overall, patients’
knowledge regarding the self-administration of sublingual GTN is
still inadequate. The findings support the need for more frequent
reinforcement of patient education, especially in the areas of
preventive use, storage and drug stability.
Abstract: Comparing other methods of waste water treatment,
constructed wetlands are one of the most fascinating practices
because being a natural process they are eco-friendly have low
construction and maintenance cost and have considerable capability
of wastewater treatment. The current research was focused mainly on
comparison of Ranunculus muricatus and Typha latifolia as wetland
plants for domestic wastewater treatment by designing and
constructing efficient pilot scale horizontal subsurface flow
mesocosms. Parameters like chemical oxygen demand, biological
oxygen demand, phosphates, sulphates, nitrites, nitrates, and
pathogenic indicator microbes were studied continuously with
successive treatments. Treatment efficiency of the system increases
with passage of time and with increase in temperature. Efficiency of
T. latifolia planted setups in open environment was fairly good for
parameters like COD and BOD5 which was showing reduction up to
82.5% for COD and 82.6% for BOD5 while DO was increased up to
125%. Efficiency of R. muricatus vegetated setup was also good but
lowers than that of T. latifolia planted showing 80.95% removal of
COD and BOD5. Ranunculus muricatus was found effective in
reducing bacterial count in wastewater. Both macrophytes were
found promising in wastewater treatment.
Abstract: Macro invertebrates have been used to monitor
organic pollution in rivers and streams. Several biotic indices based
on macro invertebrates have been developed over the years including
the Biological Monitoring Working Party (BMWP). A new biotic
index, the Gammarus:Asellus ratio has been recently proposed as an
index of organic pollution. This study tested the validity of the
Gammarus:Asellus ratio as an index of organic pollution, by
examining the relationship between the Gammarus:Asellus ratio and
physical chemical parameters, and other biotic indices such as
BMWP and, Average Score Per Taxon (ASPT) from lakes and
streams at Markeaton Park, Allestree Park and Kedleston Hall,
Derbyshire. Macro invertebrates were sampled using the standard
five minute kick sampling techniques physical and chemical
environmental variables were obtained based on standard sampling
techniques. Eighteen sites were sampled, six sites from Markeaton
Park (three sites across the stream and three sites across the lake). Six
sites each were also sampled from Allestree Park and Kedleston Hall
lakes. The Gammarus:Asellus ratio showed an opposite significant
positive correlations with parameters indicative of organic pollution
such as the level of nitrates, phosphates, and calcium and also
revealed a negatively significant correlations with other biotic indices
(BMWP/ASPT). The BMWP score correlated positively significantly
with some water quality parameters such as dissolved oxygen and
flow rate, but revealed no correlations with other chemical
environmental variables. The BMWP score was significantly higher
in the stream than the lake in Markeaton Park, also The ASPT scores
appear to be significantly higher in the upper Lakes than the middle
and lower lakes. This study has further strengthened the use of
BMWP/ASPT score as an index of organic pollution. But additional
application is required to validate the use of Gammarus:Asellus as a
rapid bio monitoring tool.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: Magnetic powder of Sr-ferrite was prepared by
conventional and sol-gel auto-combustion methods. In conventional
method, strontium carbonate and ferric oxide powders were mixed
together and then mixture was calcined. In sol-gel auto-combustion
method, a solution containing strontium nitrate, ferric nitrate and
citric acid was heated until the combustion took place automatically;
then, as-burnt powder was calcined. Thermal behavior, phase
identification, morphology and magnetic properties of powders
obtained by these two methods were compared by DTA, XRD, SEM
and VSM techniques. According to the results of DTA analysis,
formation temperature of Sr-ferrite obtained by conventional and solgel
auto-combustion methods were 1300°C and 1000°C, respectively.
XRD results confirmed the formation of pure Sr-ferrite at the
mentioned temperatures. Plate and hexagonal-shape particles of Srferrite
were observed using SEM. The Sr-ferrite powder obtained by
sol-gel auto-combustion method had saturation magnetization of
66.03 emu/g and coercivity of 5731 Oe in comparison with values of
58.20 emu/g and 4378 Oe obtained by conventional method.
Abstract: Polymer composite nano-fibers including (1, 3 wt %)
silver nano-particles have been produced by electrospinning method.
Polyacrylonitrile/N,N-dimethylformamide (PAN/DMF) solution have
been prepared and the amount of silver nitrate have been adjusted to
PAN weight. Silver nano-particles were obtained from reduction of
silver ions into silver nano-particles by chemical reduction by
hydrazine hydroxide (N2H5OH). The different amount of silver salt
was loaded into polymer matrix to obtain polyacrylonitrile composite
nano-fiber containing silver nano-particles. The effect of the amount
of silver nano-particles on the properties of composite nano-fiber web
was investigated. Electrical conductivity, mechanical properties,
thermal properties were examined by Microtest LCR Meter 6370
(0.01 mΩ-100 MΩ), Tensile tester, Differential scanning calorimeter
DSC (Q10) and SEM respectively. Also antimicrobial efficiency test
(ASTM E2149-10) was done against to Staphylococcus aureus
bacteria. It has been seen that breaking strength, conductivity,
antimicrobial effect, enthalpy during cyclization increase by use of
silver nano-particles while the diameter of nano-fiber decreases.
Abstract: Local utilities often face problems of local industrial
wastes, storm water disposal due to existing strict regulations. For
many local industries, the problem of wastewater treatment and
discharge into surface reservoirs can’t be solved through the use of
conventional biological treatment techniques. Current discharge
standards require very strict removal of a number of impurities such
as ammonia, nitrates, phosphate, etc. To reach this level of removal,
expensive reagents and sorbents are used.
The modern concept of rational water resources management
requires the development of new efficient techniques that provide
wastewater treatment and reuse.
As RO membranes simultaneously reject all dissolved impurities
such as BOD, TDS, ammonia, phosphates etc., they become very
attractive for the direct treatment of wastewater without biological
stage. To treat wastewater, specially designed membrane "open
channel" modules are used that do not possess "dead areas" that cause
fouling or require pretreatment. A solution to RO concentrate
disposal problem is presented that consists of reducing of initial
wastewater volume by 100 times. Concentrate is withdrawn from
membrane unit as sludge moisture. The efficient use of membrane
RO techniques is connected with a salt balance in water system.
Thus, to provide high ecological efficiency of developed techniques,
all components of water supply and wastewater discharge systems
should be accounted for.
Abstract: Ammonium nitrate (AN) is produced by the reaction of ammonia and nitric acid, and a waste condensate is obtained. The condensate contains pure AN in concentration up to 10g/L. The salt content in the condensate is too high to discharge immediately into the river thus it must be treated. This study is concerned with the treatment of condensates from an industrial AN production by combination of electrodialysis (ED) and electrodeionization (EDI). The condensate concentration was in range 1.9–2.5g/L of AN. A pilot ED module with 25 membrane pairs following by a laboratory EDI module with 10 membrane pairs operated continuously during 800 hours. Results confirmed that the combination of ED and EDI is suitable for the condensate treatment.
Abstract: Coagulation is a process that sanitizes leather effluents. It aims to reduce pollutants such as Chemical Oxygen Demand (COD), chloride, sulfate, chromium, suspended solids, and other dissolved solids. The current study aimed to evaluate coagulation efficiency of tannery wastewater by analyzing the change in organic matter, odor, color, ammonium ions, nutrients, chloride, H2S, sulfate, suspended solids, total dissolved solids, fecal pollution, and chromium hexavalent before and after treatment. Effluent samples were treated with coagulants Ca(OH)2 and FeSO4 .7H2O. The best advantages of this treatment included the removal of: COD (81.60%); ammonia ions (98.34%); nitrate ions (92%); chromium hexavalent (75.00%); phosphate (70.00%); chloride (69.20%); and H₂S (50%). Results also indicated a high level of efficiency in the reduction of fecal pollution indicators. Unfortunately, only a modest reduction of sulfate (19.00%) and TSS (13.00%) and an increase in TDS (15.60%) was observed.