Abstract: Cavitation inside a diesel injector nozzle is investigated numerically in this study. The Reynolds Stress Navier Stokes set of equations (RANS) are utilized to investigate flow behavior inside the nozzle numerically. Moreover, K-ε turbulent model is found to be a better approach comparing to K-ω turbulent model. The Winklhofer rectangular shape nozzle is also simulated in order to verify the current numerical scheme, and with the mass flow rate approach, the current solution is verified. Afterward, a six-hole real size nozzle was simulated and it was found that among the different fuels used in this study with the same condition, diesel fuel provides the largest length of cavitation. Also, it was found that at the same boundary condition, rapeseed methyl ester (RME) fuel leads to the highest value of discharge coefficient and mass flow rate.
Abstract: Grape seeds are waste products of wineries and often referred to as an important agricultural and industrial waste product with the potential to be used in pharmaceutical, food, and cosmetic applications. In this study, grape seed oil from traditional Ionian varieties was examined for the determination of the quality and the characteristics of each variety. Initially, the fatty acid methyl ester (FAME) profiles were analyzed using Gas Chromatography-Mass Spectrometry, after transesterification. Furthermore, other quality parameters of the grape seed oils were determined by Spectroscopy techniques, UV-Vis and Raman included. Moreover, the antioxidant capacity of the oil was measured by 2,2'-azino-bis-3-ethylbenzothiazoline-6-sulfonic acid (ABTS) and 2,2-Diphenyl-1-picrylhydrazyl (DPPH) assays and their antioxidant capacity expressed in Trolox equivalents. K and ΔΚ indices were measured in 232, 268, 270 nm, as an oil quality index. The results indicate that the air-dried grape seed total oil content ranged from 5.26 to 8.77% w/w, which is in accordance with the other grape seed varieties tested in similar studies. The composition of grape seed oil is predominated with linoleic and oleic fatty acids, with the linoleic fatty acid ranging from 53.68 to 69.95% and both the linoleic and oleic fatty acids totaling 78-82% of FAMEs, which is analogous to the fatty acid composition of safflower oil. The antioxidant assays ABTS and DPPH scored high, exhibiting that the oils have potential in the cosmetic and culinary businesses. Above that, our results demonstrate that Ionian grape seed oils have prospects that can go further than cosmetic or culinary use, into the pharmaceuticals industry. Finally, the reclamation of grape seeds from wineries waste stream is in accordance with the bio-economy strategic framework and contributes to environmental protection.
Abstract: Biofuel production especially that of biodiesel has gained tremendous attention during the last decade due to environmental concerns and shortage in petroleum oil reservoir. This research aims to investigate the influences of operating parameters, such as the alcohol-to-oil molar ratio (4:1, 6:1, and 9:1) and the amount of catalyst (1, 1.5, and 2 wt.%) on the trans esterification of refined palm oil (RPO) in a medium-scale oscillatory baffle reactor. It has been shown that an increase in the methanol-to-oil ratio resulted in an increase in fatty acid methyl esters (FAMEs) content. The amount of catalyst has an insignificant effect on the FAMEs content. Engine testing was performed on B0 (100 v/v% diesel) and blended fuel or B50 (50 v/v% diesel). Combustion of B50 was found to give lower torque compared to pure diesel. Exhaust gas from B50 was found to contain lower concentration of CO and CO2.
Abstract: Hardly any neat biodiesel satisfies the European EN14214 standard for compression ignition engine application. To satisfy the EN14214 standard, various additives are doped into biodiesel; however, biodiesel additives might cause other problems such as increase in the particular emission and increased specific fuel consumption. In addition, the additives could be expensive. Considering the increasing level of greenhouse gas GHG emissions and fossil fuel depletion, it is forecasted that the use of biodiesel will be higher in the near future. Hence, the negative aspects of the biodiesel additives will likely to gain much more importance and need to be replaced with better solutions. This study aims to satisfy the European standard EN14214 by blending the biodiesels derived from sustainable feedstocks. Waste Cooking Oil (WCO) and Animal Fat Oil (AFO) are two sustainable feedstocks in the EU (including the UK) for producing biodiesels. In the first stage of the study, these oils were transesterified separately and neat biodiesels (W100 & A100) were produced. Secondly, the biodiesels were blended together in various ratios: 80% WCO biodiesel and 20% AFO biodiesel (W80A20), 60% WCO biodiesel and 40% AFO biodiesel (W60A40), 50% WCO biodiesel and 50% AFO biodiesel (W50A50), 30% WCO biodiesel and 70% AFO biodiesel (W30A70), 10% WCO biodiesel and 90% AFO biodiesel (W10A90). The prepared samples were analysed using Thermo Scientific Trace 1300 Gas Chromatograph and ISQ LT Mass Spectrometer (GC-MS). The GS-MS analysis gave Fatty Acid Methyl Ester (FAME) breakdowns of the fuel samples. It was found that total saturation degree of the samples was linearly increasing (from 15% for W100 to 54% for A100) as the percentage of the AFO biodiesel was increased. Furthermore, it was found that WCO biodiesel was mainly (82%) composed of polyunsaturated FAMEs. Cetane numbers, iodine numbers, calorific values, lower heating values and the densities (at 15 oC) of the samples were estimated by using the mass percentages data of the FAMEs. Besides, kinematic viscosities (at 40 °C and 20 °C), densities (at 15 °C), heating values and flash point temperatures of the biomixture samples were measured in the lab. It was found that estimated and measured characterisation results were comparable. The current study concluded that biomixture fuel samples W60A40 and W50A50 were perfectly satisfying the European EN 14214 norms without any need of additives. Investigation on engine performance, exhaust emission and combustion characteristics will be conducted to assess the full feasibility of the proposed biomixture fuels.
Abstract: This study was initiated to evaluate and optimize the conversion of animal fat from tannery wastes into methyl ester. In the pre-treatment stage, animal fats feedstock was hydrolysed and esterified through solid state fermentation (SSF) using Microbacterium species immobilized onto sand silica matrix. After 72 hours of fermentation, predominant esters in the animal fats were found to be with 83.9% conversion rate. Later, esterified animal fats were transesterified at 3 hour reaction time with 1% NaOH (w/v %), 6% methanol to oil ratio (w/v %) to produce 89% conversion rate. C13 NMR revealed long carbon chain in fatty acid methyl esters at 22.2817-31.9727 ppm. Methyl esters of palmitic, stearic, oleic represented the major components in biodiesel.
Abstract: The identification of lipid and soluble sugar components in flour samples of different cultivars belonging to common oat species (Avena sativa L.) was performed: spring oat, winter oat and hulless oat. Fatty acids were extracted from flour samples with n-hexane, and derivatized into volatile methyl esters, using TMSH (trimethylsulfonium hydroxide in methanol). Soluble sugars were then extracted from defatted and dried samples of oat flour with 96% ethanol, and further derivatized into corresponding TMS-oximes, using hydroxylamine hydrochloride solution and BSTFA (N,O-bis-(trimethylsilyl)-trifluoroacetamide). The hexane and ethanol extracts of each oat cultivar were analyzed using GC-MS system. Lipid and simple sugar compositions are very similar in all samples of investigated cultivars. Chemometric tool was applied to numeric values of automatically integrated surface areas of detected lipid and simple sugar components in their corresponding derivatized forms. Hierarchical cluster analysis shows a very high similarity between the investigated flour samples of oat cultivars, according to the fatty acid content (0.9955). Moderate similarity was observed according to the content of soluble sugars (0.50). These preliminary results support the idea of establishing methods for oat flour authentication, and provide the means for distinguishing oat flour samples, regardless of the variety, from flour samples made of other cereal species, just by lipid and simple sugar profile analysis.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: In the present study, RBF neural networks were used
for predicting the performance and emission parameters of a
biodiesel engine. Engine experiments were carried out in a 4 stroke
diesel engine using blends of diesel and Honge methyl ester as the
fuel. Performance parameters like BTE, BSEC, Tex and emissions
from the engine were measured. These experimental results were
used for ANN modeling.
RBF center initialization was done by random selection and by
using Clustered techniques. Network was trained by using fixed and
varying widths for the RBF units. It was observed that RBF results
were having a good agreement with the experimental results.
Networks trained by using clustering technique gave better results
than using random selection of centers in terms of reduced MRE and
increased prediction accuracy. The average MRE for the performance
parameters was 3.25% with the prediction accuracy of 98% and for
emissions it was 10.4% with a prediction accuracy of 80%.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: Various biomass based resources, which can be used
as an extender, or a complete substitute of diesel fuel may have very
significant role in the development of agriculture, industrial and
transport sectors in the energy crisis. Use of Karanja oil methyl ester
biodiesel in a CI DI engine was found highly compatible with engine
performance along with lower exhaust emission as compared to
diesel fuel but with slightly higher NOx emission and low wear
characteristics. The combustion related properties of vegetable oils
are somewhat similar to diesel oil. Neat vegetable oils or their blends
with diesel, however, pose various long-term problems in
compression ignition engines. These undesirable features of
vegetable oils are because of their inherent properties like high
viscosity, low volatility, and polyunsaturated character. Pongamia
methyl ester (PME) was prepared by transesterification process using
methanol for long term engine operations. The physical and
combustion-related properties of the fuels thus developed were found
to be closer to that of the diesel. A neat biodiesel (PME) was selected
as a fuel for the tribological study of biofuels.
Two similar new engines were completely disassembled and
subjected to dimensioning of various vital moving parts and then
subjected to long-term endurance tests on neat biodiesel and diesel
respectively. After completion of the test, both the engines were
again disassembled for physical inspection and wear measurement of
various vital parts. The lubricating oil samples drawn from both
engines were subjected to atomic absorption spectroscopy (AAS) for
measurement of various wear metal traces present. The additional
lubricating property of biodiesel fuel due to higher viscosity as
compared to diesel fuel resulted in lower wear of moving parts and
thus improved the engine durability with a bio-diesel fuel. Results
reported from AAS tests confirmed substantially lower wear and thus
improved life for biodiesel operated engines.
Abstract: Depletion and hazardous gas emissions associated
with fossil fuels have caused scientists and global attention to focus
on the use of “alternative, eco-friendly substitutes for use in
Compression Ignition Engines. In this work, biodiesel was produced
by trans-esterification of soybean obtained from a Nigerian market
using Sodium Hydroxide (NaOH) as a catalyst.” After the
production, the physical properties (specific gravity to kinematic
viscosity and net calorific value) of the Soybean-biodiesel produced
and petrol diesel obtained from a filling station in Nigeria were
determined, and these properties conform to conventional standards
(ASTM). A cummins-6V-92TA DDEC diesel (Compression ignition,
CI) engine was run on various biodiesel-petrol diesel blends (0/100,
10/90, 20/80, 30/70 and 40/60), the B20 (blend 20/80) was found to
be the most satisfactory.
Abstract: The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with different blends of rice bran oil methyl ester and ethanol are investigated and compared with the results of standard diesel. Bio diesel produced from Rice bran oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 16.5:1, 17:1, 17.5:1 and 18:1. The impact of compression ratio on fuel consumption, brake thermal efficiency and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for Rice bran oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.
Abstract: Considering the increasing need of biofuels in Europe and the legislative requirements of the European Union it is needed to quantify the greenhouse gas emissions of biofuels life cycle. In this article a carbon footprint analysis to quantify these gases emitted during production and use of Romanian rapeseed oil (RO) and biodiesel from rapeseed oil (RME) was conducted. The functional unit was considered the LHV of diesel oil of 42.8 MJ·kg-1 corresponding to 1.15kg. of RO and 1.10 kg. of RME. When the 3 fuels were compared, the results show important benefits when using rapeseed oil or biodiesel instead of diesel. The most impacting stage in terms of GHG emissions is the use of the fuels. In this stage, rapeseed oil registers a total quantity of 3,229 kg CO2eq.·FU-1 and biodiesel register a total quantity of 3,088 kg CO2eq.·FU-1 while mineral diesel registers a total quantity of 3,156 kg CO2eq.·FU-1 emitted in the air. Taking into account that rape plant absorbed during growth stage the same quantity of CO2 as emitted into atmosphere during usage stage of the fuel, when compared the three fuels, rapeseed oil and biodiesel obtain obvious benefits against fossil diesel. Results show that by substituting diesel with RO a total quantity of 5,663 kg. CO2eq.·FU-1 would be saved while using biodiesel a total quantity of 5,570 kg. CO2eq.·FU-1 can be saved.
Abstract: Takerbucht is the only cultivar of date palm known as being resistant to the bayoud disease, caused by Fusarium oxysporum f. sp. albedinis (F.o.a.). In the aim to understand more about the defense mechanisms implied, we realized phytochemical analyses of this cultivar leaflets and roots and this, for the first time, using gas chromatography-mass spectrometry (GC-MS).The examination of our results shows that fifty-four molecules have been detected, fourteen of which are common to leaflets and roots. This study revealed also the organs' richness in derivatives fatty acids: both saturated and unsaturated are represented mainly by methyl esters of Hexadecanoic and 9,12,15-Octadecatrienoic acids. 1-Dodecanethiol, derivative Dodecanoic acid is only present in roots. It’s of great interest to note that the screening revealed the steroidal saponins abundance, among which Yamogenin acetate and Diosgenin, exclusively detected in Takerbucht. They may play an essential role, in the date palm resistance to the bayoud disease.
Abstract: Palm methyl ester (PME) is one of the alternative
biomass fuels to liquid fossil fuels. To investigate the combustion
characteristics of PME as an alternative fuel for gas turbines, combustion experiments using two types of burners under atmospheric
pressure were performed. One of the burners has a configuration
making strong non-premixed flame, whereas the other has a
configuration promoting prevaporization of fuel droplets. The results
show that the NOx emissions can be reduced by employing the latter burner without accumulation of soot when PME is used as a fuel. A
burner configuration promoting prevaporzation of fuel droplets is
recommended for PME.
Abstract: The environmental performance of rapeseed oil (RO)
and rapeseed methyl ester(RME) from winter rape as fuels produced
in Romanian agroclimate is analyzed in this paper. The proposed
methodology is life cycle assessment (LCA) and takes into
consideration the influence of grain production and agroclimatic
conditions. This study shows favorable results first for RO and then
for RME. When compared to diesel fuel, both studied biofuels show
better results in the following impact categories: Abiotic depletion
potential (ADP), Ozone layer depletion (ODP) and Photochemical
ozone creation potential (POCP).Furthermore, the environmental
performance of the two biofuels studied can be improved by
changing the type of fertilizer used and also by using biofuels instead
of diesel in the field works.
Abstract: Environmental micro-organisms include a large number of taxa and some species that are generally considered nonpathogenic, but can represent a risk in certain conditions, especially for elderly people and immunocompromised individuals. Chemotaxonomic identification techniques are powerful tools for environmental micro-organisms, and cellular fatty acid methyl esters (FAME) content is a powerful fingerprinting identification technique. A system based on an unsupervised artificial neural network (ANN) was set up using the fatty acid profiles of standard bacterial strains, obtained by gas-chromatography, used as learning data. We analysed 45 certified strains belonging to Acinetobacter, Aeromonas, Alcaligenes, Aquaspirillum, Arthrobacter, Bacillus, Brevundimonas, Enterobacter, Flavobacterium, Micrococcus, Pseudomonas, Serratia, Shewanella and Vibrio genera. A set of 79 bacteria isolated from a drinking water line (AMGA, the major water supply system in Genoa) were used as an example for identification compared to standard MIDI method. The resulting ANN output map was found to be a very powerful tool to identify these fresh isolates.
Abstract: This paper presents a spectroscopic study on doping
of Vanadyl pathalocyanine (VOPc) by [6,6]-phenyl C61 butyric acid
methyl ester (PCBM). The films are characterized by UV/Vis/NIR
spectroscopy. A drastic increase in the absorption coefficient has
been observed with increasing dopant concentration. Optical
properties of VOPc:PCBM films deposited by spin coating technique
were studied in detail. Optical band gap decreased with the PCBM
incorporation in the VOPc film. Optical band gap calculated from the
absorption spectra decreased from 3.32 eV to 3.26 eV with a
variation of 0–75 % of PCBM concentration in the VOPC films.
Abstract: In this paper, naturally immobilized lipase, Carica
papaya lipase, catalyzed biodiesel production from fish oil was
studied. The refined fish oil, extracted from the discarded parts of
fish, was used as a starting material for biodiesel production. The
effects of molar ratio of oil: methanol, lipase dosage, initial water
activity of lipase, temperature and solvent were investigated. It was
found that Carica papaya lipase was suitable for methanolysis of fish
oil to produce methyl ester. The maximum yield of methyl ester
could reach up to 83% with the optimal reaction conditions: oil:
methanol molar ratio of 1: 4, 20% (based on oil) of lipase, initial
water activity of lipase at 0.23 and 20% (based on oil) of tert-butanol
at 40oC after 18 h of reaction time. There was negligible loss in
lipase activity even after repeated use for 30 cycles.