Abstract: In this paper, determining the optimal proportionalintegral-
derivative (PID) controller gains of an single-area load
frequency control (LFC) system using genetic algorithm (GA) is
presented. The LFC is notoriously difficult to control optimally using
conventionally tuning a PID controller because the system parameters
are constantly changing. It is for this reason the GA as tuning strategy
was applied. The simulation has been conducted in MATLAB
Simulink package for single area power system. the simulation results
shows the effectiveness performance of under various disturbance.
Abstract: This paper presents a method to estimate load profile
in a multiple power flow solutions for every minutes in 24 hours per
day. A method to calculate multiple solutions of non linear profile is
introduced. The Power System Simulation/Engineering (PSS®E) and
python has been used to solve the load power flow. The result of this
power flow solutions has been used to estimate the load profiles for
each load at buses using Independent Component Analysis (ICA)
without any knowledge of parameter and network topology of the
systems. The proposed algorithm is tested with IEEE 69 test bus
system represents for distribution part and the method of ICA has
been programmed in MATLAB R2012b version. Simulation results
and errors of estimations are discussed in this paper.
Abstract: Pulse width modulation (PWM) techniques have been
the subject of intensive research for different industrial and power
sector applications. A large variety of methods, different in concept
and performance, have been newly developed and described. This
paper analyzes the comparative merits of Sinusoidal Pulse Width
Modulation (SPWM) and Space Vector Pulse Width Modulation
(SVPWM) techniques and the suitability of these techniques in a
Shunt Active Filter (SAF). The objective is to select the scheme that
offers effective utilization of DC bus voltage and also harmonic
reduction at the input side. The effectiveness of the PWM techniques
is tested in the SAF configuration with a non linear load. The
performance of the SAF with the SPWM and (SVPWM) techniques
are compared with respect to the THD in source current. The study
reveals that in the context of closed loop SAF control with the
SVPWM technique there is only a minor improvement in THD. The
utilization of the DC bus with SVPWM is also not significant
compared to that with SPWM because of the non sinusoidal
modulating signal from the controller in SAF configuration.
Abstract: Sampling and analysis of leachate from Bhalaswa
landfill and groundwater samples from nearby locations, clearly
indicated the likely contamination of groundwater due to landfill
leachate. The results of simulation studies carried out for the
migration of Chloride from landfill shows that the simulation results
are in consonance with the observed concentration of Chloride in the
vicinity of landfill facility. The solid waste disposal system presently
being practiced in Delhi consists of mere dumping of wastes
generated, at three locations Bhalaswa, Ghazipur, and Okhla without
any regard to proper care for the protection of surrounding
environment. Bhalaswa landfill site in Delhi, which is being operated
as a dump site, is expected to become cause of serious groundwater
pollution in its vicinity. The leachate from Bhalaswa landfill was
found to be having a high concentration of chlorides, as well as DOC,
COD. The present study was undertaken to determine the likely
concentrations of principle contaminants in the groundwater over a
period of time due to the discharge of such contaminants from
landfill leachates to the underlying groundwater. The observed
concentration of chlorides in the groundwater within 75m of the
radius of landfill facility was found to be in consonance with the
simulated concentration of chloride in groundwater considering one
dimensional transport model, with finite mass of contaminant source.
Governing equation of contaminant transport involving advection and
diffusion-dispersion was solved in matlab7.0 using finite difference
method.
Abstract: A wideband 2-1-1 cascaded ΣΔ modulator with a
single-bit quantizer in the two first stages and a 4-bit quantizer in the
final stage is developed. To reduce sensitivity of digital-to-analog
converter (DAC) nonlinearities in the feedback of the last stage,
dynamic element matching (DEM) is introduced. This paper presents
two modelling approaches: The first is MATLAB description and the
second is VHDL-AMS modelling of the proposed architecture and
exposes some high-level-simulation results allowing a behavioural
study. The detail of both ideal and non-ideal behaviour modelling are
presented. Then, the study of the effect of building blocks
nonidealities is presented; especially the influences of nonlinearity,
finite operational amplifier gain, amplifier slew rate limitation and
capacitor mismatch. A VHDL-AMS description presents a good
solution to predict system-s performances and can provide sensitivity
curves giving the impact of nonidealities on the system performance.
Abstract: Space Vector Pulse Width Modulation SVPWM is
one of the most used techniques to generate sinusoidal voltage and
current due to its facility and efficiency with low harmonics
distortion. This algorithm is specially used in power electronic
applications. This paper describes simulation algorithm of SVPWM
& SPWM using MatLab/simulink environment. It also implements a
closed loop three phases DC-AC converter controlling its outputs
voltages amplitude and frequency using MatLab. Also comparison
between SVPWM & SPWM results is given.
Abstract: Inter-symbol interference if not taken care off may cause severe error at the receiver and the detection of signal becomes difficult. An adaptive equalizer employing Recursive Least Squares algorithm can be a good compensation for the ISI problem. In this paper performance of communication link in presence of Least Mean Square and Recursive Least Squares equalizer algorithm is analyzed. A Model of communication system having Quadrature amplitude modulation and Rician fading channel is implemented using MATLAB communication block set. Bit error rate and number of errors is evaluated for RLS and LMS equalizer algorithm, due to change in Signal to Noise Ratio (SNR) and fading component gain in Rician fading Channel.
Abstract: The discrete-time uncertain system with time delay is investigated for bounded input bounded output (BIBO). By constructing an augmented Lyapunov function, three different sufficient conditions are established for BIBO stabilization. These conditions are expressed in the form of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. Two numerical examples are provided to demonstrate the effectiveness of the derived results.
Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: The author present PID controller design for
following control of hard disk drive by characteristic ratio assignment
method. The study in this paper concerns design of a PID controller
which sufficiently robust to the disturbances and plant perturbations
on following control of hard disk drive. Characteristic Ratio
Assignment (CRA) is shown to be an efficient control technique to
serve this requirement. The controller design by CRA is based on the
choice of the coefficients of the characteristic polynomial of the
closed loop system according to the convenient performance criteria
such as equivalent time constant and ration of characteristic
coefficient. Hence, in this study, CRA method is applied in PID
controller design for following control of hard disk drive. Matlab
simulation results shown that CRA design is fairly stable and robust
whilst giving the convenience in controller-s parameters adjustment.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: The effective machine-job assignment of injection
molding machines is very important for industry because it is not
only directly affects the quality of the product but also the
performance and lifetime of the machine as well. The phase of
machine selection was mostly done by professionals or experienced
planners, so the possibility of matching a job with an inappropriate
machine might occur when it was conducted by an inexperienced
person. It could lead to an uneconomical plan and defects. This
research aimed to develop a machine selection system for plastic
injection machines as a tool to help in decision making of the user.
This proposed system could be used both in normal times and in
times of emergency. Fuzzy logic principle is applied to deal with
uncertainty and mechanical factors in the selection of both quantity
and quality criteria. The six criteria were obtained from a plastic
manufacturer's case study to construct a system based on fuzzy logic
theory using MATLAB. The results showed that the system was able
to reduce the defects of Short Shot and Sink Mark to 24.0% and
8.0% and the total defects was reduced around 8.7% per month.
Abstract: In this paper, we propose the Modified Synchronous Detection (MSD) Method for determining the reference compensating currents of the shunt active power filter under non sinusoidal voltages conditions. For controlling the inverter switching we used the PI regulator. The numerical simulation results, using Power System Blockset Toolbox PSB of Matlab, from a complete structure, are presented and discussed.
Abstract: This paper presents a new method of fault detection and isolation (FDI) for polymer electrolyte membrane (PEM) fuel cell (FC) dynamic systems under an open-loop scheme. This method uses a radial basis function (RBF) neural network to perform fault identification, classification and isolation. The novelty is that the RBF model of independent mode is used to predict the future outputs of the FC stack. One actuator fault, one component fault and three sensor faults have been introduced to the PEMFC systems experience faults between -7% to +10% of fault size in real-time operation. To validate the results, a benchmark model developed by Michigan University is used in the simulation to investigate the effect of these five faults. The developed independent RBF model is tested on MATLAB R2009a/Simulink environment. The simulation results confirm the effectiveness of the proposed method for FDI under an open-loop condition. By using this method, the RBF networks able to detect and isolate all five faults accordingly and accurately.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: In this paper, Differential Evolution (DE) algorithm, a new promising evolutionary algorithm, is proposed to train Radial Basis Function (RBF) network related to automatic configuration of network architecture. Classification tasks on data sets: Iris, Wine, New-thyroid, and Glass are conducted to measure the performance of neural networks. Compared with a standard RBF training algorithm in Matlab neural network toolbox, DE achieves more rational architecture for RBF networks. The resulting networks hence obtain strong generalization abilities.
Abstract: A control system design with Characteristic Ratio
Assignment (CRA) is proven that effective for SISO control design.
But the control system design for MIMO via CRA is not concrete
procedure. In this paper presents the control system design method
for quadruple-tank process via CRA. By using the decentralized
method for both minimum phase and non-minimum phase are made.
The results from PI and PID controller design via CRA can be
illustrated the validity of our approach by MATLAB.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: An actual power plant, which is the power plant of Iron and Steel Factory at Misurata city in Libya , has been modeled using Matlab in order to compare its results to the actual results of the actual cycle. This paper concentrates on two factors:
a- The comparison between exergy losses in the actual cycle and the modeled cycle.
b- The effect of extracting pressure on temperature water at boiler inlet.
Closed heat exchangers used in this plant have been substituted by open heat exchangers in the current study of the modeled power plant and the required changes in the pressure have been considered. In the following investigation the two points mentioned above are taken in consideration.