Abstract: Desalination using solar energy coupled with membrane techniques such as vacuum membrane distillation (VMD) is considered as an interesting alternative for the production of pure water. During this work, a developed model of a polytetrafluoroethylene (PTFE) hollow fiber membrane module of a VMD unit of seawater was carried out. This simulation leads to establishing a comparison between the effects of two different equations of the vaporization latent heat on the membrane surface temperature and on the unit productivity. Besides, in order to study the effect of putting membrane modules in series on the outlet fluid temperature and on the productivity of the process, a simulation was executed.
Abstract: The latent heat thermal energy storage system is a
thrust area of research due to exuberant thermal energy storage
potential. The thermal performance of PCM is significantly
augmented by installation of the high thermal conductivity fins. The
objective of the present study is to obtain optimum size and location
of the fins to enhance diffusion heat transfer without altering overall
melting time. Hence, the constructal theory is employed to eliminate,
resize, and re-position the fins. A numerical code based on conjugate
heat transfer coupled enthalpy porosity approached is developed to
solve Navier-Stoke and energy equation. The numerical results show
that the constructal fin design has enhanced the thermal performance
along with the increase in the overall volume of PCM when
compared to conventional. The overall volume of PCM is found to be
increased by half of total of volume of fins. The elimination and repositioning
the fins at high temperature gradient from low
temperature gradient is found to be vital.
Abstract: In this study, a form-stable composite Paraffin/Nanoclay (PA-NC) has been prepared by absorbing PA into porous particles of NC to be used for low-temperature latent heat thermal energy storage. The leakage test shows that the maximum mass fraction of PA that can be incorporated in NC without leakage is 60 wt.%. Differential scanning calorimetry (DSC) has been used to measure the thermal properties of the PA and PA-NC both before and after incorporation in plasterboard (PL). The mechanical performance of the samples has been evaluated in flexural mode. The thermal energy storage performance has been studied using a small test chamber (100 mm × 100 mm × 100 mm) made from 10 mm thick PL and measuring the temperatures using thermocouples. The flammability of the PL+PL-NC has been discussed using a cone calorimeter. The results indicate that the form composite PA has good potential for use as thermal energy storage materials in building applications.
Abstract: Fabric as the first and most common layer that is in permanent contact with human skin is a very good interface to provide coverage, as well as heat and cold insulation. Phase change materials (PCMs) are organic and inorganic compounds which have the capability of absorbing and releasing noticeable amounts of latent heat during phase transitions between solid and liquid phases at a low temperature range. PCMs come across phase changes (liquid-solid and solid-liquid transitions) during absorbing and releasing thermal heat; so, in order to use them for a long time, they should have been encapsulated in polymeric shells, so-called microcapsules. Microencapsulation and nanoencapsulation methods have been developed in order to reduce the reactivity of a PCM with outside environment, promoting the ease of handling, decreasing the diffusion and evaporation rates. Methods of incorporation of PCMs in textiles such as electrospinning and determining thermal properties had been summarized. Paraffin waxes catch a lot of attention due to their high thermal storage density, repeatability of phase change, thermal stability, small volume change during phase transition, chemical stability, non-toxicity, non-flammability, non-corrosive and low cost and they seem to play a key role in confronting with climate change and global warming. In this article, we aimed to review the researches concentrating on the characteristics of PCMs and new materials and methods of microencapsulation.
Abstract: The present work aims to investigate numerically the thermal and flow characteristics of a rectangular latent heat storage unit (LHSU) during the melting process of a phase change material (PCM). The LHSU consists of a number of vertical and identical plates of PCM separated by rectangular channels. The melting process is initiated when the LHSU is heated by a heat transfer fluid (HTF: water) flowing in channels in a downward or upward direction. The proposed study is motivated by the need to optimize the thermal performance of the LHSU by accelerating the charging process. A mathematical model is developed and a fixed-grid enthalpy formulation is adopted for modeling the melting process coupling with convection-conduction heat transfer. The finite volume method was used for discretization. The obtained numerical results are compared with experimental, analytical and numerical ones found in the literature and reasonable agreement is obtained. Thereafter, the numerical investigations were carried out to highlight the effects of the HTF flow direction and the aspect ratio of the PCM slabs on the heat transfer characteristics and thermal performance enhancement of the LHSU.
Abstract: Exposure to ionizing radiation has been found to induce changes in poly(vinylidene fluoride) (PVDF) homopolymers. The high dose gamma irradiation process induces the formation of C=C and C=O bonds in its [CH2-CF2]n main chain. The irradiation also provokes crosslinking and chain scission. All these radio-induced defects lead to changes in the PVDF crystalline structure. As a consequence, it is common to observe a decrease in the melting temperature (TM) and melting latent heat (LM) and some changes in its ferroelectric features. We have investigated the possibility of preparing nanocomposites of PVDF with graphene oxide (GO) through the radio-induction of molecular bonds. In this work, we discuss how the gamma radiation interacts with the nanocomposite crystalline structure.
Abstract: Melting of Paraffin Wax (P116) dispersed with Al2O3 nanoparticles in a rectangular latent heat storage unit (LHSU) is numerically investigated. The storage unit consists of a number of vertical and identical plates of nano-enhanced phase change material (NEPCM) separated by rectangular channels in which heat transfer fluid flows (HTF: Water). A two dimensional mathematical model is considered to investigate numerically the heat and flow characteristics of the LHSU. The melting problem was formulated using the enthalpy porosity method. The finite volume approach was used for solving equations. The effects of nanoparticles’ volumetric fraction and the Reynolds number on the thermal performance of the storage unit were investigated.
Abstract: Solar energy is available abundantly in the world, but it is not continuous and its intensity also varies with time. Due to above reason the acceptability and reliability of solar based thermal system is lower than conventional systems. A properly designed heat storage system increases the reliability of solar thermal systems by bridging the gap between the energy demand and availability. In the present work, two dimensional numerical simulation of the melting of heat storage material is presented in the horizontal annulus of double pipe latent heat storage system. Longitudinal fins were used as a thermal conductivity enhancement. Paraffin wax was used as a heat-storage or phase change material (PCM). Constant wall temperature is applied to heat transfer tube. Presented two-dimensional numerical analysis shows the movement of melting front in the finned cylindrical annulus for analyzing the thermal behavior of the system during melting.
Abstract: The irradiation of polymeric materials has received
much attention because it can produce diverse changes in chemical
structure and physical properties. Thus, studying the chemical and
structural changes of polymers is important in practice to achieve
optimal conditions for the modification of polymers. The effect of
gamma irradiation on the crystalline structure of poly(vinylidene
fluoride) (PVDF) has been investigated using differential scanning
calorimetry (DSC) and X-ray diffraction techniques (XRD). Gamma
irradiation was carried out in atmosphere air with doses between 100
kGy at 3,000 kGy with a Co-60 source. In the melting thermogram of
the samples irradiated can be seen a bimodal melting endotherm is
detected with two melting temperature. The lower melting
temperature is attributed to melting of crystals originally present and
the higher melting peak due to melting of crystals reorganized upon
heat treatment. These results are consistent with those obtained by
XRD technique showing increasing crystallinity with increasing
irradiation dose, although the melting latent heat is decreasing.
Abstract: The effect of various humidities on process yields and
degrees of crystallinity for spray-dried powders from spray drying of
lactose with humid air in a straight-through system have been
studied. It has been suggested by Williams–Landel–Ferry kinetics
(WLF) that a higher particle temperature and lower glass-transition
temperature would increase the crystallization rate of the particles
during the spray-drying process. Freshly humidified air produced by
a Buchi-B290 spray dryer as a humidifier attached to the main spray
dryer decreased the particle glass-transition temperature (Tg), while
allowing the particle temperature (Tp) to reach higher values by using
an insulated drying chamber. Differential scanning calorimetry
(DSC) and moisture sorption analysis were used to measure the
degree of crystallinity for the spray-dried lactose powders. The
results showed that higher Tp-Tg, as a result of applying humid air,
improved the process yield from 21 ± 4 to 26 ± 2% and crystallinity
of the particles by decreasing the latent heat of crystallization from
43 ± 1 to 30 ± 11 J/g and the sorption peak height from 7.3 ± 0.7% to
6 ± 0.7%.
Abstract: A one-dimensional mathematical model was developed in order to analyze and optimize the latent heat storage wall. The governing equations for energy transport were developed by using the enthalpy method and discretized with volume control scheme. The resulting algebraic equations were next solved iteratively by using TDMA algorithm. A series of numerical investigations were conducted in order to examine the effects of the thickness of the PCM layer on the thermal behavior of the proposed heating system. Results are obtained for thermal gain and temperature fluctuation. The charging discharging process was also presented and analyzed.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: As application of re-activation of backside on power
device Insulated Gate Bipolar Transistor (IGBT), laser annealing was
employed to irradiate amorphous silicon substrate, and resistivities
were measured using four point probe measurement. For annealing
the amorphous silicon two lasers were used at wavelength of visible
green (532 nm) together with Infrared (793 nm). While the green
laser efficiently increased temperature at top surface the Infrared
laser reached more deep inside and was effective for melting the
top surface. A finite element method was employed to evaluate time
dependent thermal distribution in silicon substrate.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: The study and development of an innovative material
for building insulation is really important for a sustainable society in order to improve comfort and reducing energy consumption. The aim of this work is the development of insulating panels for
sustainable buildings based on an innovative material made by
cardboard and Phase Change Materials (PCMs).
The research has consisted in laboratory tests whose purpose has been the obtaining of the required properties for insulation panels: lightweight, porous structures and mechanical resistance. PCMs have been used for many years in the building industry as
smart insulation technology because of their properties of storage and release high quantity of latent heat at useful specific temperatures [1]- [2].
The integration of PCMs into cellulose matrix during the waste paper recycling process has been developed in order to obtain a
composite material.
Experiments on the productive process for the realization of insulating panels were done in order to make the new material
suitable for building application. The addition of rising agents
demonstrated the possibility to obtain a lighter structure with better
insulation properties.
Several tests were conducted to verify the new panel properties. The results obtained have shown the possibility to realize an
innovative and sustainable material suitable to replace insulating panels currently used.
Abstract: In the present work an investigation of the effects of
the air frontal velocity, relative humidity and dry air temperature on
the heat transfer characteristics of plain finned tube evaporator has
been conducted. Using an appropriate correlation for the air side heat
transfer coefficient the temperature distribution along the fin surface
was calculated using a dimensionless temperature distribution. For a
constant relative humidity and bulb temperature, it is found that the
temperature distribution decreases with increasing air frontal
velocity. Apparently, it is attributed to the condensate water film
flowing over the fin surface. When dry air temperature and face
velocity are being kept constant, the temperature distribution
decreases with the increase of inlet relative humidity. An increase in
the inlet relative humidity is accompanied by a higher amount of
moisture on the fin surface. This results in a higher amount of latent
heat transfer which involves higher fin surface temperature. For the
influence of dry air temperature, the results here show an increase in
the dimensionless temperature parameter with a decrease in bulb
temperature. Increasing bulb temperature leads to higher amount of
sensible and latent heat transfer when other conditions remain
constant.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.