Abstract: In recent research copper and manganese systems
were found to be the most active in CO and organic compounds
oxidation among the base catalysts. The mixed copper manganese
oxide has been widely studied in oxidation reactions because of their
higher activity at low temperatures in comparison with single oxide
catalysts. The results showed that the formation of spinel
CuxMn3−xO4 in the oxidized catalyst is responsible for the activity
even at room temperature. That is why the most of the investigations
are focused on the hopcalite catalyst (CuMn2O4) as the best coppermanganese
catalyst. Now it’s known that this is true only for CO
oxidation, but not for mixture of CO and VOCs. The purpose of this
study is to investigate the alumina supported copper-manganese
catalysts with different Cu/Mn molar ratio in terms of oxidation of
CO, methanol and dimethyl ether. The catalysts were prepared by impregnation of γ-Al2O3 with
copper and manganese nitrates and the catalytic activity
measurements were carried out in two stage continuous flow
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions closest possible to the industrial. Gas
mixtures on the input and output of the reactor were analyzed with a
gas chromatograph, equipped with FID and TCD detectors. The
texture characteristics were determined by low-temperature (- 196oС)
nitrogen adsorption in a Quantachrome Instruments NOVA 1200e
(USA) specific surface area & pore analyzer. Thermal, XRD and
TPR analyses were performed. It was established that the active component of the mixed Cu-
Mn/γ–alumina catalysts strongly depends on the Cu/Mn molar ratio.
Highly active alumina supported Cu-Mn catalysts for CO, methanol
and DME oxidation were synthesized. While the hopcalite is the best
catalyst for CO oxidation, the best compromise for simultaneous
oxidation of all components is the catalyst with Cu/Mn molar ratio
1:5.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: The literature on language teaching and second
language acquisition has been largely driven by monolingual
ideology with a common assumption that a second language (L2) is
best taught and learned in the L2 only. The current study challenges
this assumption by reporting learners' positive perceptions of tertiary
level teachers' code switching practices in Vietnam. The findings of
this study contribute to our understanding of code switching practices
in language classrooms from a learners' perspective.
Data were collected from student participants who were working
towards a Bachelor degree in English within the English for Business
Communication stream through the use of focus group interviews.
The literature has documented that this method of interviewing has a
number of distinct advantages over individual student interviews. For
instance, group interactions generated by focus groups create a more
natural environment than that of an individual interview because they
include a range of communicative processes in which each individual
may influence or be influenced by others - as they are in their real
life. The process of interaction provides the opportunity to obtain the
meanings and answers to a problem that are "socially constructed
rather than individually created" leading to the capture of real-life
data. The distinct feature of group interaction offered by this
technique makes it a powerful means of obtaining deeper and richer
data than those from individual interviews. The data generated
through this study were analysed using a constant comparative
approach. Overall, the students expressed positive views of this
practice indicating that it is a useful teaching strategy. Teacher code
switching was seen as a learning resource and a source supporting
language output. This practice was perceived to promote student
comprehension and to aid the learning of content and target language
knowledge. This practice was also believed to scaffold the students'
language production in different contexts. However, the students
indicated their preference for teacher code switching to be
constrained, as extensive use was believed to negatively impact on
their L2 learning and trigger cognitive reliance on the L1 for L2
learning. The students also perceived that when the L1 was used to a
great extent, their ability to develop as autonomous learners was
negatively impacted.
This study found that teacher code switching was supported in
certain contexts by learners, thus suggesting that there is a need for
the widespread assumption about the monolingual teaching approach
to be re-considered.
Abstract: Waste Load Allocation (WLA) strategies usually
intend to find economic policies for water resource management.
Water quality trading (WQT) is an approach that uses discharge
permit market to reduce total environmental protection costs. This
primarily requires assigning discharge limits known as total
maximum daily loads (TMDLs). These are determined by monitoring
organizations with respect to the receiving water quality and
remediation capabilities. The purpose of this study is to compare two
approaches of TMDL assignment for WQT policy in small catchment
area of Haraz River, in north of Iran. At first, TMDLs are assigned
uniformly for the whole point sources to keep the concentrations of
BOD and dissolved oxygen (DO) at the standard level at checkpoint
(terminus point). This was simply simulated and controlled by
Qual2kw software. In the second scenario, TMDLs are assigned
using multi objective particle swarm optimization (MOPSO) method
in which the environmental violation at river basin and total treatment
costs are minimized simultaneously. In both scenarios, the equity
index and the WLA based on trading discharge permits (TDP) are
calculated. The comparative results showed that using economically
optimized TMDLs (2nd scenario) has slightly more cost savings rather
than uniform TMDL approach (1st scenario). The former annually
costs about 1 M$ while the latter is 1.15 M$. WQT can decrease
these annual costs to 0.9 and 1.1 M$, respectively. In other word,
these approaches may save 35 and 45% economically in comparison
with command and control policy. It means that using multi objective
decision support systems (DSS) may find more economical WLA,
however its outcome is not necessarily significant in comparison with
uniform TMDLs. This may be due to the similar impact factors of
dischargers in small catchments. Conversely, using uniform TMDLs
for WQT brings more equity that makes stakeholders not feel that
much envious of difference between TMDL and WQT allocation. In
addition, for this case, determination of TMDLs uniformly would be
much easier for monitoring. Consequently, uniform TMDL for TDP
market is recommended as a sustainable approach. However,
economical TMDLs can be used for larger watersheds.
Abstract: This paper focuses on a critical component of the
situational awareness (SA), the control of autonomous vertical flight
for vectored thrust aerial vehicle (VTAV). With the SA strategy, we
proposed a neural network motion control procedure to address the
dynamics variation and performance requirement difference of flight
trajectory for a VTAV. This control strategy with using of NARMAL2
neurocontroller for chosen model of VTAV has been verified by
simulation of take-off and forward maneuvers using software
package Simulink and demonstrated good performance for fast
stabilization of motors, consequently, fast SA with economy in
energy can be asserted during search-and-rescue operations.
Abstract: Sol-enhanced Zn-Ni-Al2O3 nanocomposite coatings
were electroplated on mild steel by our newly developed solenhanced
electroplating method. In this method, transparent Al2O3 sol
was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3nanocomposite
coatings. The chemical composition, microstructure and
mechanical properties of the composite and alloy coatings deposited
at two different agitation speed were investigated. The structure of all
coatings was single γ-Ni5Zn21 phase. The composite coatings possess
refined crystals with higher microhardness compared to Zn-Ni alloy
coatings. The wear resistance of Zn-Ni coatings was improved
significantly by incorporation of alumina nano particles into the
coatings. Higher agitation speed provided more uniform coatings
with smaller grain sized and slightly higher microhardness.
Considering composite coatings, high agitation speeds may facilitate
co-deposition of alumina in the coatings.
Abstract: Al6061 alloy base matrix, reinforced with particles of
silicon carbide (10 wt %) and Graphite powder (1wt%), known as
hybrid composites have been fabricated by liquid metallurgy route
(stir casting technique) and optimized at different parameters like
applied load, sliding speed and sliding distance by taguchi method. A
plan of experiment generated through taguchi technique was used to
perform experiments based on L27 orthogonal array. The developed
ANOVA and regression equations are used to find the optimum
coefficient of friction and wear under the influence of applied load,
sliding speed and sliding distance. On the basis of “smaller the best”
the dry sliding wear resistance was analysed and finally confirmation
tests were carried out to verify the experimental results.
Abstract: Advanced treatments such as forward osmosis (FO)
can be used to separate or reject nutrients from secondary treated
effluents. Forward osmosis uses the chemical potential across the
membrane, which is the osmotic pressure gradient, to induce water to
flow through the membrane from a feed solution (FS) into a draw
solution (DS). The performance of FO is affected by the membrane
characteristics, composition of the FS and DS, and operating
conditions. The aim of this study was to investigate the optimum
velocity and temperature for nutrient rejection and water flux
performance in FO treatments. MgCl2 was used as the DS in the FO
process. The results showed that higher cross flow velocities yielded
higher water fluxes. High rejection of nutrients was achieved by using
a moderate cross flow velocity at 0.25 m/s. Nutrient rejection was
insensitive to temperature variation, whereas water flux was
significantly impacted by it. A temperature of 25°C was found to be
good for nutrient rejection.
Abstract: This paper analyses the heat transfer performance and
fluid flow using different nanofluids in a square enclosure. The
energy equation and Navier-Stokes equation are solved numerically
using finite volume scheme. The effect of volume fraction
concentration on the enhancement of heat transfer has been studied
icorporating the Brownian motion; the influence of effective thermal
conductivity on the enhancement was also investigated for a range of
volume fraction concentration. The velocity profile for different
Rayleigh number. Water-Cu, water AL2O3 and water-TiO2 were
tested.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: Fly ash (FA) thanks to the significant presence of SiO2
and Al2O3 as the main components is a potential raw material for
geopolymers production. Mechanical activation is a method for
improving FA reactivity and also the porosity of final mixture; those
parameters can be analysed through sorption properties. They have
direct impact on the durability of fly ash based geopolymer mortars.
In the paper, effect of FA fineness on sorption properties of
geopolymers based on sodium silicate, as well as relationship
between fly ash fineness and apparent density, compressive and
flexural strength of geopolymers are presented. The best results in the
evaluated area reached the sample H1, which contents the highest
portion of particle under 20μm (100% of GFA). The interdependence
of individual tested properties was confirmed for geopolymer
mixtures corresponding to those in the cement based mixtures: higher
is portion of fine particles < 20μm, higher is strength, density and
lower are sorption properties. The compressive strength as well as
sorption parameters of the geopolymer can be reasonably controlled
by grinding process and also ensured by the higher share of fine
particle (to 20μm) in total mass of the material.
Abstract: Activated carbon is an amorphous carbon chain which
has extremely extended surface area. High surface area of activated
carbon is due to the porous structure. Activated carbon, using a
variety of materials such as coal and cellulosic materials; can be
obtained by both physical and chemical methods. The prepared
activated carbon can be used for decolorize, deodorize and also can
be used for removal of organic and non-organic pollution. In this
study, pomegranate peel was subjected to 800W microwave power
for 1 to 4 minutes. Also fresh pomegranate peel was used for the
reference material. Then ZnCl2 was used for the chemical activation
purpose. After the activation process, activated pomegranate peels
were used for the adsorption of Zn metal (40 ppm) in the waste water.
As a result of the adsorption experiments, removal of heavy metals
ranged from 89% to 85%.
Abstract: Nanofibers of PVA /nickel nitrate/silica/alumina
izopropoxide/boric acid composite were prepared by using sol-gel
processing and electrospinning technique. By high temperature
calcinations of the above precursor fibers, nanofibers of
NiO/Al2O3/B2O3/SiO2 composite with diameters about 500 nm
could be successfully obtained. The fibers were characterized by
XRD and SEM analyses.
Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.
Abstract: The development of active and stable catalysts
without noble metals for low temperature oxidation of exhaust gases
remains a significant challenge. The purpose of this study is to
determine the influence of the preparation method on the catalytic
activity of the supported copper-manganese mixed oxides in terms of
VOCs oxidation. The catalysts were prepared by impregnation of γ-
Al2O3 with copper and manganese nitrates and acetates and the
possibilities for CO, CH3OH and dimethyl ether (DME) oxidation
were evaluated using continuous flow equipment with a four-channel
isothermal stainless steel reactor. Effect of the support, Cu/Mn mole
ratio, heat treatment of the precursor and active component loading
were investigated. Highly active alumina supported Cu-Mn catalysts
for CO and VOCs oxidation were synthesized. The effect of
preparation conditions on the activity behavior of the catalysts was
discussed.
The synergetic interaction between copper and manganese species
increases the activity for complete oxidation over mixed catalysts.
Type of support, calcination temperature and active component
loading along with catalyst composition are important factors,
determining catalytic activity. Cu/Mn molar ratio of 1:5, heat
treatment at 450oC and 20 % active component loading are the best
compromise for production of active catalyst for simultaneous
combustion of CO, CH3OH and DME.
Abstract: Catalytic combustion of methane is imperative due to
stability of methane at low temperature. Methane (CH4), therefore,
remains unconverted in vehicle exhausts thereby causing greenhouse
gas GHG emission problem. In this study, heterogeneous catalysts of
palladium with bio-char (2 wt% Pd/Bc) and Al2O3 (2wt% Pd/ Al2O3)
supports were prepared by incipient wetness impregnation and then
subsequently tested for catalytic combustion of CH4. Support-porous
heterogeneous catalytic combustion (HCC) material were selected
based on factors such as surface area, porosity, thermal stability,
thermal conductivity, reactivity with reactants or products, chemical
stability, catalytic activity, and catalyst life. Sustainable and
renewable support-material of bio-mass char derived from palm shell
waste material was compared with those from the conventional
support-porous materials. Kinetic rate of reaction was determined for
combustion of methane on Palladium (Pd) based catalyst with Al2O3
support and bio-char (Bc). Material characterization was done using
TGA, SEM, and BET surface area. The performance test was
accomplished using tubular quartz reactor with gas mixture ratio of
3% methane and 97% air. The methane porous-HCC conversion was
carried out using online gas analyzer connected to the reactor that
performed porous-HCC. BET surface area for prepared 2 wt% Pd/Bc
is smaller than prepared 2wt% Pd/ Al2O3 due to its low porosity
between particles. The order of catalyst activity based on kinetic rate
on reaction of catalysts in low temperature was 2wt%
Pd/Bc>calcined 2wt% Pd/ Al2O3> 2wt% Pd/ Al2O3>calcined 2wt%
Pd/Bc. Hence agro waste material can successfully be utilized as an
inexpensive catalyst support material for enhanced CH4 catalytic
combustion.
Abstract: Array-based gene expression analysis is a powerful
tool to profile expression of genes and to generate information on
therapeutic effects of new anti-cancer compounds. Anti-apoptotic
effect of thymoquinone was studied in MCF7 breast cancer cell line
using gene expression profiling with cDNA microarray. The purity
and yield of RNA samples were determined using RNeasyPlus Mini
kit. The Agilent RNA 6000 NanoLabChip kit evaluated the quantity
of the RNA samples. AffinityScript RT oligo-dT promoter primer
was used to generate cDNA strands. T7 RNA polymerase was used to
convert cDNA to cRNA. The cRNA samples and human universal
reference RNA were labelled with Cy-3-CTP and Cy-5-CTP,
respectively. Feature Extraction and GeneSpring softwares analysed
the data. The single experiment analysis revealed involvement of 64
pathways with up-regulated genes and 78 pathways with downregulated
genes. The MAPK and p38-MAPK pathways were
inhibited due to the up-regulation of PTPRR gene. The inhibition of
p38-MAPK suggested up-regulation of TGF-ß pathway. Inhibition of
p38-MAPK caused up-regulation of TP53 and down-regulation of
Bcl2 genes indicating involvement of intrinsic apoptotic pathway.
Down-regulation of CARD16 gene as an adaptor molecule regulated
CASP1 and suggested necrosis-like programmed cell death and
involvement of caspase in apoptosis. Furthermore, down-regulation
of GPCR, EGF-EGFR signalling pathways suggested reduction of
ER. Involvement of AhR pathway which control cytochrome P450
and glucuronidation pathways showed metabolism of Thymoquinone.
The findings showed differential expression of several genes in
apoptosis pathways with thymoquinone treatment in estrogen
receptor-positive breast cancer cells.
Abstract: Co metal supported on SiO2 and Al2O3 catalysts with
a metal loading varied from 30 of 70 wt.% were evaluated for
decomposition of methane to COx free hydrogen and carbon
nanomaterials. The catalytic runs were carried out from 550-800oC
under atmospheric pressure using fixed bed vertical flow reactor. The
fresh and spent catalysts were characterized by BET surface area
analyzer, XRD, SEM, TEM and TG analysis. The data showed that
50% Co/Al2O3 catalyst exhibited remarkable higher activity at 800oC
with respect to H2 production compared to rest of the catalysts.
However, the catalytic activity and durability was greatly declined at
higher temperature. The main reason for the catalytic inhibition of Co
containing SiO2 catalysts is the higher reduction temperature of
Co2SiO4. TEM images illustrate that the carbon materials with
various morphologies, carbon nanofibers (CNFs), helical-shaped
CNFs and branched CNFs depending on the catalyst composition and
reaction temperature were obtained.
Abstract: The borate glasses are known by their structural
characterized by existence of unit’s structural composed by triangles
and tetrahedrons boron in different configurations depending on the
percentage of B2O3 in the glass chemical composition. In this paper,
effect of lithium oxide addition on the thermal and physical
properties of an alumina borate glass, was investigated. It was found
that the boron abnormality has a significant effect in the change of
glass properties according to the addition rate of lithium oxide.
Abstract: Near-infrared spectroscopy (NIRS) has been widely
used as a non-invasive method to measure brain activity, but it is
corrupted by baseline drift noise. Here we present a method to measure
regional cerebral blood flow as a derivative of NIRS output. We
investigate whether, when listening to languages, blood flow can
reasonably localize and represent regional brain activity or not. The
prefrontal blood flow distribution pattern when advanced
second-language listeners listened to a second language (L2) was most
similar to that when listening to their first language (L1) among the
patterns of mean and standard deviation. In experiments with 25
healthy subjects, the maximum blood flow was localized to the left
BA46 of advanced listeners. The blood flow presented is robust to
baseline drift and stably localizes regional brain activity.