Abstract: Fossil fuel-firing power plants dominate electric
power generation in Taiwan, which are also the major contributor to
Green House gases (GHG). CO2 is the most important greenhouse
gas that cause global warming. This paper penetrates the relationship
between carbon trading for GHG reduction and power generation
expansion planning (GEP) problem for the electrical utility. The
Particle Swarm Optimization (PSO) Algorithm is presented to deal
with the generation expansion planning strategy of the utility with
independent power providers (IPPs). The utility has to take both the
IPPs- participation and environment impact into account when a new
generation unit is considering expanded from view of supply side.
Abstract: Toxoplasma gondii is an intracellular parasite capable
of infecting all nucleated cells in a diverse array of species.
Toxoplasma plaque assay have been described using Bacto Agar.
Because of its experimental advantages carboxymethyl cellulose
overlay, medium viscosity was choosing and the aim of this work
was to develop alternative method for formation of T. gondii plaques.
Tachyzoites were inoculated onto monolayers of Vero cells and
cultured at 37° C under 5 % CO2. The cultures were followed up by
microscopy inspection. Small plaques were visible by naphtol blue
stain 4 days after infection. Larger plaques could be observed by day
10 of culture. The carboxymethyl cellulose is a cheap reagent and the
methodology is easier, faster than assays under agar overlay. This is
the first description of the carboxymethyl cellulose overlay use for
obtaining the formation of T. gondii plaques and may be useful in
consequent obtaining tachyzoites for detailed studies.
Abstract: In order to avoid the potentially devastating
consequences of global warming and climate change, the carbon
dioxide “CO2" emissions caused due to anthropogenic activities must
be reduced considerably. This paper presents the first study
examining the feasibility of carbon sequestration in construction and
demolition “C&D" waste. Experiments were carried out in a self
fabricated Batch Reactor at 40ºC, relative humidity of 50-70%, and
flow rate of CO2 at 10L/min for 1 hour for water-to-solids ratio of 0.2
to 1.2. The effect of surface area was found by comparing the
theoretical extent of carbonation of two different sieve sizes (0.3mm
and 2.36mm) of C&D waste. A 38.44% of the theoretical extent of
carbonation equating to 4% CO2 sequestration extent was obtained
for C&D waste sample for 0.3mm sieve size. Qualitative,
quantitative and morphological analyses were done to validate
carbonate formation using X-ray diffraction “X.R.D.," thermal
gravimetric analysis “T.G.A., “X-Ray Fluorescence Spectroscopy
“X.R.F.," and scanning electron microscopy “S.E.M".
Abstract: Continuous measurements and multivariate methods are applied in researching the effects of energy consumption on indoor air quality (IAQ) in a Finnish one-family house. Measured data used in this study was collected continuously in a house in Kuopio, Eastern Finland, during fourteen months long period. Consumption parameters measured were the consumptions of district heat, electricity and water. Indoor parameters gathered were temperature, relative humidity (RH), the concentrations of carbon dioxide (CO2) and carbon monoxide (CO) and differential air pressure. In this study, self-organizing map (SOM) and Sammon's mapping were applied to resolve the effects of energy consumption on indoor air quality. Namely, the SOM was qualified as a suitable method having a property to summarize the multivariable dependencies into easily observable two-dimensional map. Accompanying that, the Sammon's mapping method was used to cluster pre-processed data to find similarities of the variables, expressing distances and groups in the data. The methods used were able to distinguish 7 different clusters characterizing indoor air quality and energy efficiency in the study house. The results indicate, that the cost implications in euros of heating and electricity energy vary according to the differential pressure, concentration of carbon dioxide, temperature and season.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: This research is to study the performance of heat
pump dryer for drying of kaffir lime leaves under different media and
to compare the color values and essential oil content of final products
after drying. In the experiments, kaffir lime leaves were dried in the
closed-loop system at drying temperatures of 40, 50 and 60 oC. The
drying media used in this study were hot air, CO2 and N2 gases. The
velocity of drying media in the drying chamber was 0.4 m/s with
bypass ratio of 30%. The initial moisture content of kaffir lime leaves
was approximately 180-190 % d.b. It was dried until down to a final
moisture content of 10% d.b. From the experiments, the results
showed that drying rate, the coefficient of performance (COP) and
specific energy consumption (SEC) depended on drying temperature.
While drying media did not affect on drying rate. The time for kaffir
lime leaves drying at 40, 50 and 60 oC was 10, 5 and 3 hours,
respectively. The performance of the heat pump system decreased
with drying temperature in the range of 2.20-3.51. In the aspect of
final product color, the greenness and overall color had a great
change under drying temperature at 60 oC rather than drying at 40
and 50 oC. When compared among drying media, the greenness and
overall color of product dried with hot air at 60 oC had a great change
rather than dried with CO2 and N2.
Abstract: This study focused on arsenate removal by nano
zero-valent iron (NZVI) in the gas-bubbled aqueous solution. It
appears that solution acidified by H2SO4 is far more favorable than by
CO2-bubbled acidification. In addition, as dissolved oxygen was
stripped out of solution by N2 gas bubbling, the arsenate removal
dropped significantly. To take advantages of common practice of
carbonation and oxic condition, pretreatment of CO2 and air bubbling
in sequence are recommended for a better removal of arsenate.
Abstract: Permeability reduction induced by asphaltene
precipitation during gas injection is one of the serious problems in
the oil industry. This problem can lead to formation damage and
decrease the oil production rate. In this work, Malaysian light oil
sample has been used to investigate the effect CO2 injection and
Water Alternating Gas (WAG) injection on permeability reduction.
In this work, dynamic core flooding experiments were conducted to
study the effect of CO2 and WAG injection on the amount of
asphaltene precipitated. Core properties after displacement were
inspected for any permeability reduction to study the effect of
asphaltene precipitation on rock properties.
The results showed that WAG injection gave less asphaltene
precipitation and formation damage compared to CO2 injection. The
study suggested that WAG injection can be one of the important
factors of managing asphaltene precipitation.
Abstract: This paper focuses on assessment of air pollution in Umm-Alhyman, Kuwait, which is located south to oil refineries, power station, oil field, and highways. The measurements were made over a period of four days in March and July in 2001, 2004, and 2008. The measured pollutants included methanated and nonmethanated hydrocarbons (MHC, NMHC), CO, CO2, SO2, NOX, O3, and PM10. Also, meteorological parameters were measured, which includes temperature, wind speed and direction, and solar radiation. Over the study period, data analysis showed increase in measured SO2, NOX and CO by factors of 1.2, 5.5 and 2, respectively. This is explained in terms of increase in industrial activities, motor vehicle density, and power generation. Predictions of the measured data were made by the ISC-AERMOD software package and by using the ISCST3 model option. Finally, comparison was made between measured data against international standards.
Abstract: As the fossil fuels kept on depleting, intense research in developing hydrogen (H2) as the alternative fuel has been done to cater our tremendous demand for fuel. The potential of H2 as the ultimate clean fuel differs with the fossil fuel that releases significant amounts of carbon dioxide (CO2) into the surrounding and leads to the global warming. The experimental work was carried out to study the production of H2 from palm kernel shell steam gasification at different variables such as heating rate, steam to biomass ratio and adsorbent to biomass ratio. Maximum H2 composition which is 61% (volume basis) was obtained at heating rate of 100oCmin-1, steam/biomass of 2:1 ratio, and adsorbent/biomass of 1:1 ratio. The commercial adsorbent had been modified by utilizing the alcoholwater mixture. Characteristics of both adsorbents were investigated and it is concluded that flowability and floodability of modified CaO is significantly improved.
Abstract: The use of neural networks is popular in various
building applications such as prediction of heating load, ventilation
rate and indoor temperature. Significant is, that only few papers deal
with indoor carbon dioxide (CO2) prediction which is a very good
indicator of indoor air quality (IAQ). In this study, a data-driven
modelling method based on multilayer perceptron network for indoor
air carbon dioxide in an apartment building is developed.
Temperature and humidity measurements are used as input variables
to the network. Motivation for this study derives from the following
issues. First, measuring carbon dioxide is expensive and sensors
power consumptions is high and secondly, this leads to short
operating times of battery-powered sensors. The results show that
predicting CO2 concentration based on relative humidity and
temperature measurements, is difficult. Therefore, more additional
information is needed.
Abstract: A comprehensive discussion of feasible strategies for sustainable energy supply is urgently needed to achieve a turnaround of the current energy situation. The necessary fundamentals required for the development of a long term energy vision are lacking to a great extent due to the absence of reasonable long term scenarios that fulfill the requirements of climate protection and sustainable energy use. The contribution of the study is based on a search for sustainable energy paths in the long run for Austria. The analysis makes use of secondary data predominantly. The measures developed to avoid CO2 emissions and other ecological risk factors vary to a great extent among all economic sectors. This is shown by the calculation of CO2 cost of abatement curves. In this study it is demonstrated that the most effective technical measures with the lowest CO2 abatement costs yield solutions to the current energy problems. Various scenarios are presented concerning the question how the technological and environmental options for a sustainable energy system for Austria could look like in the long run. It is shown how sustainable energy can be supplied even with today-s technological knowledge and options available. The scenarios developed include an evaluation of the economic costs and ecological impacts. The results are not only applicable to Austria but demonstrate feasible and cost efficient ways towards a sustainable future.
Abstract: This paper presents the experimental as well as the
simulated performance studies on the transcritical CO2 heat pumps
for simultaneous water cooling and heating; effects of water mass
flow rates and water inlet temperatures of both evaporator and gas
cooler on the cooling and heating capacities, system COP and water
outlets temperatures are investigated. Study shows that both the
water mass flow rate and inlet temperature have significant effect on
system performances. Test results show that the effect of evaporator
water mass flow rate on the system performances and water outlet
temperatures is more pronounced (COP increases 0.6 for 1 kg/min)
compared to the gas cooler water mass flow rate (COP increases 0.4
for 1 kg/min) and the effect of gas cooler water inlet temperature is
more significant (COP decreases 0.48 for given ranges) compared to
the evaporator water inlet temperature (COP increases 0.43 for given
ranges). Comparisons of experimental values with simulated results
show the maximum deviation of 5% for cooling capacity, 10% for
heating capacity, 16% for system COP. This study offers useful
guidelines for selecting appropriate water mass flow rate to obtain
required system performance.
Abstract: We investigated this hypothesis that arterial CO2 pressure (PaCO2) drives ventilation (V.E) with a time delay duringrecovery from short impulse-like exercise (10 s) with work load of 200 watts. V.E and end tidal CO2 pressure (PETCO2) were measured continuously during rest, warming up, exercise and recovery periods. PaCO2 was predicted (PaCO2 pre) from PETCO2 and tidal volume (VT). PETCO2 and PaCO2 pre peaked at 20 s of recovery. V.E increased and peaked at the end of exercise and then decreased during recovery; however, it peaked again at 30 s of recovery, which was 10 s later than the peak of PaCO2 pre. The relationship between V. E and PaCO2pre was not significant by using data of them obtained at the same time but was significant by using data of V.E obtained 10 s later for data of PaCO2 pre. The results support our hypothesis that PaCO2 drives V.E with a time delay.
Abstract: Experiments were carried out at the Faculty of Food
Technology of Latvia University of Agriculture (LLU). Soft cheese
Kleo produced in Latvia was packed in a biodegradable PLA without
barrierproperties and VC999 BioPack lidding film PLA, coated with
a barrier of pure silicon oxide (SiOx) and in combination with
modified atmosphere (MAP) the influence on the shelf life was
investigated and compared with some conventional (OPP, PE/PA,
PE/OPA and Multibarrier 60) polymer film impact. Modified
atmosphere consisted of carbon dioxide CO2 (E 290) 30% and
nitrogen N2 (E 941) 70%. The analyzable samples were stored at the
temperature of +4.0±0.5 °C up to 32 days- and analyzed before
packaging and in the 0, 5th, 11th, 15th, 18th, 22nd, 25th, 29th and 32nd
day of storage. The shelf life was extended along to 32 days, good
outside appearance and lactic acid aroma was observed.
Abstract: Carbon dioxide is one of the major green house gases.
It is removed from different streams using amine absorption process.
Sterically hindered amines are suggested as good CO2 absorbers.
Solubility of carbon dioxide (CO2) was measured in aqueous
solutions of 2-Amino-2-methyl-1-propanol (AMP) at temperatures 30
oC, 40 oC and 60 oC. The effect of pressure and temperature was
studied over various concentrations of AMP. It has been found that
pressure has positive effect on CO2 solubility where as solubility
decreased with increasing temperature. Absorption performance of
AMP increased with increasing pressure. Solubility of aqueous AMP
was compared with mo-ethanolamine (MEA) and the absorption
capacity of aqueous solutions of AMP was found to be better.
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.
Abstract: The objective of the research was to evaluate the
hardness stability of milk pomade sweets packed in several
packaging materials (OPP, Multibarrier 60 HFP, BIALON 65
HFP, BIALON 50 HFP, ECOLEAN) by several packaging
technologies – modified atmosphere (MAP) (consisting of
30% CO2+70% N2; 30% N2+70% CO2 and 100% CO2) and
control – in air ambiance. Samples were stored at the room
temperature +21±1 °C. The studies of the samples were
carried out before packaging and after 2, 4, 6, 8, and 10
storage weeks.
Abstract: The purpose of the study was to determine the amount of Palm Kernel Oil (PKO) extracted from a packed bed of palm kernels in a supercritical fluid extractor using supercritical carbon dioxide (SC-CO2) as an environmental friendly solvent. Further, the study sought to ascertain the values of the overall mass transfer coefficient (K) of PKO evaluation through a mass transfer model, at constant temperature of 50 °C, 60 °C, and 70 °C and pressures range from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa respectively. Finally, the study also seeks to demonstrate the application of the overall mass transfer coefficient values in relation to temperature and pressure. The overall mass transfer coefficient was found to be dependent pressure at each constant temperature of 50 °C, 60 °C and 70 °C. The overall mass transfer coefficient for PKO in a packed bed of palm kernels was found to be in the range of 1.21X 10-4 m min-1 to 1.72 X 10-4 m min-1 for a constant temperature of 50 °C and in the range of 2.02 X 10-4 m min-1 to 2.43 X 10-4 m min-1 for a constant temperature of 60 °C. Similar increasing trend of the overall mass transfer coefficient from 1.77 X 10-4 m min-1 to 3.64 X 10-4 m min-1 was also observed at constant temperature of 70 °C within the same pressure range from 27.6 MPa to 48.3 MPa.