Abstract: The current statuses of lifetime test of LaB6 hollow
cathode at the Lanzhou Institute of Physics (LIP), China, was
described. 5A LaB6 hollow cathode was design for LIPS-200 40mN
Xenon ion thruster, and it could be used for LHT-100 80 mN Hall
thruster, too. Life test of the discharge and neutralizer modes of LHC-5
hollow cathode were stared in October 2011, and cumulative operation
time reached 17,300 and 16,100 hours in April 2015, respectively. The
life of cathode was designed more than 11,000 hours. Parameters of
discharge and key structure dimensions were monitored in different
stage of life test indicated that cathodes were health enough. The test
will continue until the cathode cannot work or operation parameter is
not in normally. The result of the endurance test of cathode
demonstrated that the LaB6 hollow cathode is satisfied for the required
of thruster in life and performance.
Abstract: Reduction of energy consumption in built
infrastructure, through the installation of energy-efficient
technologies, is a major approach to achieving sustainability. In
practice, the viability of energy efficiency projects strongly depends
on the cost reimbursement and profitability. These projects are
subject to failure if the actual cost savings do not reimburse the
project cost promptly. In such cases, refinancing could be a solution
to benefit from the long-term returns of the project, if implemented
wisely. However, very little is still known about the effect of
refinancing options on financial performance of energy efficiency
projects. In order to fill this gap, the present study investigates the
financial behavior of energy efficiency projects with focus on
refinancing options, such as Leveraged Loans. A System Dynamics
(SD) model is introduced, and the model application is presented
using an actual case-study data. The case study results indicate that
while high-interest start-ups make using Leveraged Loan inevitable,
refinancing can rescue the project and bring about profitability. This
paper also presents some managerial implications of refinancing
energy efficiency projects based on the case-study analysis. Results
of this study help to implement financially viable energy efficiency
projects so that the community could benefit from their
environmental advantages widely.
Abstract: In this paper, the unstable angle of attack of a
FOXTROT aircraft is controlled by using Genetic Algorithm based
flight controller and the result is compared with the conventional
techniques like Tyreus-Luyben (TL), Ziegler-Nichols (ZN) and
Interpolation Rule (IR) for tuning the PID controller. In addition, the
performance indices like Mean Square Error (MSE), Integral Square
Error (ISE), and Integral Absolute Time Error (IATE) etc. are
improved by using Genetic Algorithm. It was established that the
error by using GA is very less as compared to the conventional
techniques thereby improving the performance indices of the
dynamic system.
Abstract: Highly developed technology and highly competitive
global market highlight the important role of competitive advantages
and operation performances in sustainable company operation.
Activity-Based Costing (ABC) provides accurate operation cost and
operation performance information. Rich literatures provide relevant
research with cases study on Activity-Based Costing application, but
the research on cause relationship between key success factors and its
specific outcome, such as profitability or share market are few. These
relationships provide the ways to handle the key success factors to
achieve the specific outcomes for ensuring to promote the competitive
advantages and operation performances. The main purposes of this
research are exploring the key success paths by Key Success Paths
approach which will lead the ways to apply Activity-Base Costing.
The Key Success Paths is the innovative method which is exploring
the cause relationships and explaining what are the effects of key
success factors to specific outcomes of Activity-Based Costing
implementation. The cause relationships between key success factors
and successful specific outcomes are Key Success Paths (KSPs). KSPs
are the guidelines to lead the cost management strategies to achieve the
goals of competitive advantages and operation performances. The
research findings indicate that good management system design may
affect the well outcomes of Activity-Based Costing application and
achieve to outstanding competitive advantage, operating performance
and profitability as well by KSPs exploration.
Abstract: High Performance Liquid Chromatography (HPLC)
method was developed and validated for simultaneous estimation of
6-Gingerol(6G) and 6-Shogaol(6S) in joint pain relief gel containing
ginger extract. The chromatographic separation was achieved by
using C18 column, 150 x 4.6mm i.d., 5μ Luna, mobile phase
containing acetonitrile and water (gradient elution). The flow rate
was 1.0 ml/min and the absorbance was monitored at 282 nm. The
proposed method was validated in terms of the analytical parameters
such as specificity, accuracy, precision, linearity, range, limit of
detection (LOD), limit of quantification (LOQ), and determined
based on the International Conference on Harmonization (ICH)
guidelines. The linearity ranges of 6G and 6S were obtained over 20-
60 and 6-18 μg/ml respectively. Good linearity was observed over the
above-mentioned range with linear regression equation Y= 11016x-
23778 for 6G and Y = 19276x-19604 for 6S (x is concentration of
analytes in μg/ml and Y is peak area). The value of correlation
coefficient was found to be 0.9994 for both markers. The limit of
detection (LOD) and limit of quantification (LOQ) for 6G were
0.8567 and 2.8555 μg/ml and for 6S were 0.3672 and 1.2238 μg/ml
respectively. The recovery range for 6G and 6S were found to be
91.57 to 102.36 % and 84.73 to 92.85 % for all three spiked levels.
The RSD values from repeated extractions for 6G and 6S were 3.43
and 3.09% respectively. The validation of developed method on
precision, accuracy, specificity, linearity, and range were also
performed with well-accepted results.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: Fading noise degrades the performance of cellular
communication, most notably in femto- and pico-cells in 3G and 4G
systems. When the wireless channel consists of a small number of
scattering paths, the statistics of fading noise is not analytically
tractable and poses a serious challenge to developing closed
canonical forms that can be analysed and used in the design of
efficient and optimal receivers. In this context, noise is multiplicative
and is referred to as stochastically local fading. In many analytical
investigation of multiplicative noise, the exponential or Gamma
statistics are invoked. More recent advances by the author of this
paper utilized a Poisson modulated-weighted generalized Laguerre
polynomials with controlling parameters and uncorrelated noise
assumptions. In this paper, we investigate the statistics of multidiversity
stochastically local area fading channel when the channel
consists of randomly distributed Rayleigh and Rician scattering
centers with a coherent Nakagami-distributed line of sight component
and an underlying doubly stochastic Poisson process driven by a
lognormal intensity. These combined statistics form a unifying triply
stochastic filtered marked Poisson point process model.
Abstract: Sub-Saharan Africa is described as the second fastest
growing in mobile phone penetration in the world more than in the
United States or the European Union. Mobile phones have been used
to provide a lot of opportunities to improve people’s lives in the
region such as in banking, marketing, entertainment, and paying for
various bills such as water, TV, and electricity. However, the
potential of mobile phones to enhance teaching and learning has not
been explored. This study presents an experience of developing and
delivering SMS based quiz questions used to assess mastery of
subject content knowledge of science and mathematics secondary
school teachers in Tanzania. The SMS quizzes were used as a follow
up support mechanism to 500 teachers who participated in a project
to upgrade subject content knowledge of teachers in science and
mathematics subjects in Tanzania. Quizzes of 10-15 questions were
sent to teachers each week for 8 weeks and the results were analyzed
using SPSS. Results show that teachers who participated in chemistry
and biology subjects have better performance compared to those who
participated in mathematics and physics subjects. Teachers reported
some challenges that led to poor performance, This research has
several practical implications for those who are implementing or
planning to use mobile phones in teaching and learning especially in
rural secondary schools in sub-Saharan Africa.
Abstract: Direct Torque Control (DTC) is an AC drive control
method especially designed to provide fast and robust responses. In
this paper a progressive algorithm for direct torque control of threephase
induction drive system supplied by photovoltaic arrays using
voltage source inverter to control motor torque and flux with
maximum power point tracking at different level of insolation is
presented. Experimental results of the new DTC method obtained by
an experimental rapid prototype system for drives are presented.
Simulation and experimental results confirm that the proposed system
gives quick, robust torque and speed responses at constant switching
frequencies.
Abstract: This article proposes a hybrid algorithm for spectrum
allocation in cognitive radio networks based on the algorithms
Analytical Hierarchical Process (AHP) and Technique for Order of
Preference by Similarity to Ideal Solution (TOPSIS) to improve the
performance of the spectrum mobility of secondary users in cognitive
radio networks. To calculate the level of performance of the proposed algorithm a
comparative analysis between the proposed AHP-TOPSIS, Grey
Relational Analysis (GRA) and Multiplicative Exponent Weighting
(MEW) algorithm is performed. Four evaluation metrics are used.
These metrics are accumulative average of failed handoffs,
accumulative average of handoffs performed, accumulative average
of transmission bandwidth, and accumulative average of the
transmission delay. The results of the comparison show that AHP-TOPSIS Algorithm
provides 2.4 times better performance compared to a GRA Algorithm
and, 1.5 times better than the MEW Algorithm.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: This paper presents a case study of using STATCOM to enhance the performance of Al-Qatraneh 33-kV transmission line. The location of the STATCOM was identified by maintaining minimum voltage drops at the 110 load nodes. The transmission line and the 110 load nodes have been modeled by MATLAB/Simulink. The suggested STATCOM and its location will increase the transmission capability of this transmission line and overcome the overload expected in the year 2020. The annual percentage loading rise has been considered as 14.35%. A graphical representation of the line-to-line voltages and the voltage drops at different load nodes is illustrated.
Abstract: Novel wind-lens turbine designs can augment power
output. Vacuum-Assisted Resin Transfer Molding (VARTM) is used
to form large and complex structures from a Carbon Fiber Reinforced
Polymer (CFRP) composite. Typically, wind-lens turbine structures
are fabricated in segments, and then bonded to form the final structure.
This paper introduces five new adhesive joints, divided into two
groups: one is constructed between dry carbon and CFRP fabrics, and
the other is constructed with two dry carbon fibers. All joints and
CFRP fabrics were made in our laboratory using VARTM
manufacturing techniques. Specimens were prepared for tensile testing
to measure joint performance. The results showed that the second
group of joints achieved a higher tensile strength than the first group.
On the other hand, the tensile fracture behavior of the two groups
showed the same pattern of crack originating near the joint ends
followed by crack propagation until fracture.
Abstract: Non-linear dynamic time history analysis is
considered as the most advanced and comprehensive analytical
method for evaluating the seismic response and performance of
multi-degree-of-freedom building structures under the influence of
earthquake ground motions. However, effective and accurate
application of the method requires the implementation of advanced
hysteretic constitutive models of the various structural components
including masonry infill panels. Sophisticated computational research
tools that incorporate realistic hysteresis models for non-linear
dynamic time-history analysis are not popular among the professional
engineers as they are not only difficult to access but also complex and
time-consuming to use. In addition, commercial computer programs
for structural analysis and design that are acceptable to practicing
engineers do not generally integrate advanced hysteretic models
which can accurately simulate the hysteresis behavior of structural
elements with a realistic representation of strength degradation,
stiffness deterioration, energy dissipation and ‘pinching’ under cyclic
load reversals in the inelastic range of behavior. In this scenario,
push-over or non-linear static analysis methods have gained
significant popularity, as they can be employed to assess the seismic
performance of building structures while avoiding the complexities
and difficulties associated with non-linear dynamic time-history
analysis. “Push-over” or non-linear static analysis offers a practical
and efficient alternative to non-linear dynamic time-history analysis
for rationally evaluating the seismic demands. The present paper is
based on the analytical investigation of the effect of distribution of
masonry infill panels over the elevation of planar masonry infilled
reinforced concrete [R/C] frames on the seismic demands using the
capacity spectrum procedures implementing nonlinear static analysis
[pushover analysis] in conjunction with the response spectrum
concept. An important objective of the present study is to numerically
evaluate the adequacy of the capacity spectrum method using
pushover analysis for performance based design of masonry infilled
R/C frames for near-field earthquake ground motions.
Abstract: The paper is focused to the evaluation railway tracks
in the Slovakia by using Multi-Criteria method. Evaluation of railway
tracks has important impacts for the assessment of investment in
technical equipment. Evaluation of railway tracks also has an
important impact for the allocation of marshalling yards. Marshalling
yards are in transport model as centers for the operation assigned
catchment area. This model is one of the effective ways to meet the
development strategy of the European Community's railways. By
applying this model in practice, a transport company can guarantee a
higher quality of service and then expect an increase in performance.
The model is also applicable to other rail networks. This model
supplements a theoretical problem of train formation problem of new
ways of looking at evaluation of factors affecting the organization of
wagon flows.
Abstract: The contemporary battlefield creates a demand for
more costly and highly advanced munitions. Training personnel
responsible for operations as well as immediate execution of combat
tasks which engage real asset is unrealistic and economically not
feasible. Owing to a wide array of exploited simulators and various
types of imitators, it is possible to reduce the costs. One of the
effective elements of training, which can be applied in the training of
all service branches, is imitator of aerial targets. This research serves
as an introduction to the commencement of design analysis over a
real aerial target imitator. Within the project, the basic aerodynamic
calculations were made, which enabled to determine its geometry,
design layout, performance as well as mass balance of individual
components. The conducted calculations of the parameters of flight
characteristics come closer to the real performance of such
Unmanned Aerial Vehicles.
Abstract: Brain-Computer Interfaces (BCIs) measure brain
signals activity, intentionally and unintentionally induced by users,
and provides a communication channel without depending on the
brain’s normal peripheral nerves and muscles output pathway.
Feature Selection (FS) is a global optimization machine learning
problem that reduces features, removes irrelevant and noisy data
resulting in acceptable recognition accuracy. It is a vital step
affecting pattern recognition system performance. This study presents
a new Binary Particle Swarm Optimization (BPSO) based feature
selection algorithm. Multi-layer Perceptron Neural Network
(MLPNN) classifier with backpropagation training algorithm and
Levenberg-Marquardt training algorithm classify selected features.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.
Abstract: This research tested the performance of alternative
warehouse designs concerning the picking process. The chosen
performance measures were Travel Distance and Total Fulfilment
Time. An explanatory case study was built up around a model
implemented with SIMUL8. Hypotheses were set by selecting
outcomes from the literature survey matching popular empirical
findings. 17.4% reductions were found for Total Fulfilment Time and
Resource Utilisation. The latter was then used as a proxy for
operational efficiency. Literal replication of theoretical data-patterns
was considered as an internal validity sign. Assessing the estimated
changes benefits ahead of implementation was found to be a
contribution to practice.
Abstract: The paper is focused on the operational model for
transport the single wagon consignments on railway network by
using two different models of train formation. The paper gives an
overview of possibilities of improving the quality of transport
services. Paper deals with two models used in problematic of train
formatting - time continuously and time discrete. By applying these
models in practice, the transport company can guarantee a higher
quality of service and expect increasing of transport performance.
The models are also applicable into others transport networks. The
models supplement a theoretical problem of train formation by new
ways of looking to affecting the organization of wagon flows.