Abstract: Today we are unmarking the secrets of the universe by exploring different stars and planets and most of the space exploration is done by unmanned space robots. In addition to our planet Earth, there are pieces of evidence that show other astronomical objects in our solar system such as Venus, Mars, Saturn’s moon Titan and Uranus support the flight of fixed wing air vehicles. In this paper, we take forward the concept of presence of large rounded tubercles along the leading edge of a wing and use it as a passive flow control device that will help in improving its aerodynamic performance and maneuverability. Furthermore, in this research, aerodynamic measurements and performance analysis of wavy leading tubercles on the fixed wings at 5-degree angle of attack are carried out after determination of the flow conditions on the selected planetary bodies. Wavelength and amplitude for the sinusoidal modifications on the leading edge are analyzed and simulations are carried out for three-dimensional NACA 0012 airfoil maintaining unity AR (Aspect Ratio). Tubercles have consistently demonstrated the ability to delay and decrease the severity of stall as per the studies were done in the Earth’s atmosphere. Implementing the same design on the leading edges of Micro-Air Vehicles (MAVs) and UAVs could make these aircrafts more stable over a greater range of angles of attack in different planetary environments of our solar system.
Abstract: Significant legislative changes are set to revolutionise the commercial shipping industry. Upcoming emissions restrictions will force operators to look at technologies that can improve the efficiency of their vessels -reducing fuel consumption and emissions. A device which may help in this challenge is the Ship Wind-Assisted Propulsion system (SWAP), an actively controlled aerofoil mounted vertically on the deck of a ship. The device functions in a similar manner to a sail on a yacht, whereby the aerodynamic forces generated by the sail reach an equilibrium with the hydrodynamic forces on the hull and a forward velocity results. Numerical and experimental testing of the SWAP device is presented in this study. Circulation control takes the form of a co-flow jet aerofoil, utilising both blowing from the leading edge and suction from the trailing edge. A jet at the leading edge uses the Coanda effect to energise the boundary layer in order to delay flow separation and create high lift with low drag. The SWAP concept has been originated by the research and development team at SMAR Azure Ltd. The device will be retrofitted to existing ships so that a component of the aerodynamic forces acts forward and partially reduces the reliance on existing propulsion systems. Wind tunnel tests have been carried out at the de Havilland wind tunnel at the University of Glasgow on a 1:20 scale model of this system. The tests aim to understand the airflow characteristics around the aerofoil and investigate the approximate lift and drag coefficients that an early iteration of the SWAP device may produce. The data exhibits clear trends of increasing lift as injection momentum increases, with critical flow attachment points being identified at specific combinations of jet momentum coefficient, Cµ, and angle of attack, AOA. Various combinations of flow conditions were tested, with the jet momentum coefficient ranging from 0 to 0.7 and the AOA ranging from 0° to 35°. The Reynolds number across the tested conditions ranged from 80,000 to 240,000. Comparisons between 2D computational fluid dynamics (CFD) simulations and the experimental data are presented for multiple Reynolds-Averaged Navier-Stokes (RANS) turbulence models in the form of normalised surface pressure comparisons. These show good agreement for most of the tested cases. However, certain simulation conditions exhibited a well-documented shortcoming of RANS-based turbulence models for circulation control flows and over-predicted surface pressures and lift coefficient for fully attached flow cases. Work must be continued in finding an all-encompassing modelling approach which predicts surface pressures well for all combinations of jet injection momentum and AOA.
Abstract: OpenVSP is an aerodynamic solver developed by National Aeronautics and Space Administration (NASA) that allows building a reliable model of an aircraft. This software performs an aerodynamic simulation according to the angle of attack of the aircraft makes between the incoming airstream, and its speed. A reliable aerodynamic model of the Cessna Citation X was designed but it required a lot of computation time. As a consequence, a prediction method was established that allowed predicting lift and drag coefficients for all Mach numbers and for all angles of attack, exclusively for stall conditions, from a computation of three angles of attack and only one Mach number. Aerodynamic coefficients given by the prediction method for a Cessna Citation X model were finally compared with aerodynamics coefficients obtained using a complete OpenVSP study.
Abstract: Effect of plunging motion on the pitch oscillating NACA0012 airfoil is investigated using computational fluid dynamics (CFD). A simulation model based on overset grid technology and k - ω shear stress transport (SST) turbulence model is established, and the numerical simulation results are compared with available experimental data and other simulations. Two cases of phase angle φ = 0, μ which represents the phase difference between the pitching and plunging motions of an airfoil are performed. Airfoil vortex generation, moving, and shedding are discussed in detail. Good agreements have been achieved with the available literature. The upward plunging motion made the equivalent angle of attack less than the actual one during pitching analysis. It is observed that the formation of the stall vortex is suppressed, resulting in a decrease in the lift coefficient and a delay of the stall angle. However, the downward plunging motion made the equivalent angle of attack higher the actual one.
Abstract: Computations for two-dimensional flow past a stationary and harmonically pitching wind turbine airfoil at a moderate value of Reynolds number (400000) are carried out by progressively increasing the angle of attack for stationary airfoil and at fixed pitching frequencies for rotary one. The incompressible Navier-Stokes equations in conjunction with Unsteady Reynolds Average Navier-Stokes (URANS) equations for turbulence modeling are solved by OpenFOAM package to investigate the aerodynamic phenomena occurred at stationary and pitching conditions on a NACA 6-series wind turbine airfoil. The aim of this study is to enhance the accuracy of numerical simulation in predicting the aerodynamic behavior of an oscillating airfoil in OpenFOAM. Hence, for turbulence modelling, k-ω-SST with low-Reynolds correction is employed to capture the unsteady phenomena occurred in stationary and oscillating motion of the airfoil. Using aerodynamic and pressure coefficients along with flow patterns, the unsteady aerodynamics at pre-, near-, and post-static stall regions are analyzed in harmonically pitching airfoil, and the results are validated with the corresponding experimental data possessed by the authors. The results indicate that implementing the mentioned turbulence model leads to accurate prediction of the angle of static stall for stationary airfoil and flow separation, dynamic stall phenomenon, and reattachment of the flow on the surface of airfoil for pitching one. Due to the geometry of the studied 6-series airfoil, the vortex on the upper surface of the airfoil during upstrokes is formed at the trailing edge. Therefore, the pattern flow obtained by our numerical simulations represents the formation and change of the trailing-edge vortex at near- and post-stall regions where this process determines the dynamic stall phenomenon.
Abstract: Redundancy requirements for UAV (Unmanned Aerial
Vehicle) are hardly faced due to the generally restricted amount
of available space and allowable weight for the aircraft systems,
limiting their exploitation. Essential equipment as the Air Data,
Attitude and Heading Reference Systems (ADAHRS) require several
external probes to measure significant data as the Angle of Attack
or the Sideslip Angle. Previous research focused on the analysis
of a patented technology named Smart-ADAHRS (Smart Air Data,
Attitude and Heading Reference System) as an alternative method to
obtain reliable and accurate estimates of the aerodynamic angles.
This solution is based on an innovative sensor fusion algorithm
implementing soft computing techniques and it allows to obtain a
simplified inertial and air data system reducing external devices.
In fact, only one external source of dynamic and static pressures
is needed. This paper focuses on the benefits which would be
gained by the implementation of this system in UAV applications.
A simplification of the entire ADAHRS architecture will bring to
reduce the overall cost together with improved safety performance.
Smart-ADAHRS has currently reached Technology Readiness Level
(TRL) 6. Real flight tests took place on ultralight aircraft equipped
with a suitable Flight Test Instrumentation (FTI). The output of
the algorithm using the flight test measurements demonstrates the
capability for this fusion algorithm to embed in a single device
multiple physical and virtual sensors. Any source of dynamic and
static pressure can be integrated with this system gaining a significant
improvement in terms of versatility.
Abstract: This paper presents a study on the trajectory of a two stage launch vehicle. The study includes dynamic responses of motion parameters as well as the variation of angles affecting the orientation of the launch vehicle (LV). LV dynamic characteristics including state vector variation with corresponding altitude and velocity for the different LV stages separation, as well as the angle of attack and flight path angles are also discussed. A flight trajectory study for the drop zone of first stage and the jettisoning of fairing are introduced in the mathematical modeling to study their effect. To increase the accuracy of the LV model, atmospheric model is used taking into consideration geographical location and the values of solar flux related to the date and time of launch, accurate atmospheric model leads to enhancement of the calculation of Mach number, which affects the drag force over the LV. The mathematical model is implemented on MATLAB based software (Simulink). The real available experimental data are compared with results obtained from the theoretical computation model. The comparison shows good agreement, which proves the validity of the developed simulation model; the maximum error noticed was generally less than 10%, which is a result that can lead to future works and enhancement to decrease this level of error.
Abstract: In this research, a numerical simulation of an Electrohydrodynamic (EHD) actuator’s effects on the flow around a square cylinder by using a finite volume method has been investigated. This is one of the newest ways for controlling the fluid flows. Two plate electrodes are flush-mounted on the surface of the cylinder and one wire electrode is placed on the line with zero angle of attack relative to the stagnation point and excited with DC power supply. The discharge produces an electric force and changes the local momentum behaviors in the fluid layers. For this purpose, after selecting proper domain and boundary conditions, the electric field relating to the problem has been analyzed and then the results in the form of electrical body force have been entered in the governing equations of fluid field (Navier-Stokes equations). The effect of ionic wind resulted from the Electrohydrodynamic actuator, on the velocity, pressure and the wake behind cylinder has been considered. According to the results, it is observed that the fluid flow accelerates in the nearest wall of the frontal half of the cylinder and the pressure difference between frontal and hinder cylinder is increased.
Abstract: This paper seeks the potentials of studying aerodynamic characteristics of inward cavities called dimples, as an alternative to the classical vortex generators. Increasing stalling angle is a greater challenge in wing design. But our examination is primarily focused on increasing lift. In this paper, enhancement of lift is mainly done by introduction of dimple or cavity in a wing. In general, aircraft performance can be enhanced by increasing aerodynamic efficiency that is lift to drag ratio of an aircraft wing. Efficiency improvement can be achieved by improving the maximum lift co-efficient or by reducing the drag co-efficient. At the time of landing aircraft, high angle of attack may lead to stalling of aircraft. To avoid this kind of situation, increase in the stalling angle is warranted. Hence, improved stalling characteristic is the best way to ease landing complexity. Computational analysis is done for the wing segment made of NACA 0012. Simulation is carried out for 30 m/s free stream velocity over plain airfoil and different types of cavities. The wing is modeled in CATIA V5R20 and analyses are carried out using ANSYS CFX. Triangle and square shapes are used as cavities for analysis. Simulations revealed that cavity placed on wing segment shows an increase of maximum lift co-efficient when compared to normal wing configuration. Flow separation is delayed at downstream of the wing by the presence of cavities up to a particular angle of attack.
Abstract: This paper presents results of numerical and experimental studies on a two-dimensional (2D) flapping elliptic airfoil in a forward flight condition at Reynolds number of 5000. The study is motivated from an earlier investigation which shows that the deterioration in thrust performance of a sinusoidal heaving and pitching 2D (NACA0012) airfoil at high flapping frequency can be recovered by changing the effective angle of attack profile to square wave, sawtooth, or cosine wave shape. To better understand why such modifications lead to superior thrust performance, we take a closer look at the transient aerodynamic force behavior of an airfoil when the effective angle of attack profile changes gradually from a generic smooth trapezoidal profile to a sinusoid shape by modifying the base length of the trapezoid. The choice of using a smooth trapezoidal profile is to avoid the infinite acceleration condition encountered in the square wave profile. Our results show that the enhancement in the time-averaged thrust performance at high flapping frequency can be attributed to the delay and reduction in the drag producing valley region in the transient thrust force coefficient when the effective angle of attack profile changes from sinusoidal to trapezoidal.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: This paper presents the performance characteristics of
Darrieus-type vertical axis wind turbine (VAWT) with NACA airfoil
blades. The performance of Darrieus-type VAWT can be
characterized by torque and power. There are various parameters
affecting the performance such as chord length, helical angle, pitch
angle and rotor diameter. To estimate the optimum shape of Darrieustype
wind turbine in accordance with various design parameters, we
examined aerodynamic characteristics and separated flow occurring
in the vicinity of blade, interaction between flow and blade, and
torque and power characteristics derived from it. For flow analysis,
flow variations were investigated based on the unsteady RANS
(Reynolds-averaged Navier-Stokes) equation. Sliding mesh algorithm
was employed in order to consider rotational effect of blade. To
obtain more realistic results we conducted experiment and numerical
analysis at the same time for three-dimensional shape. In addition,
several parameters (chord length, rotor diameter, pitch angle, and
helical angle) were considered to find out optimum shape design and
characteristics of interaction with ambient flow. Since the NACA
airfoil used in this study showed significant changes in magnitude of
lift and drag depending on an angle of attack, the rotor with low drag,
long cord length and short diameter shows high power coefficient in
low tip speed ratio (TSR) range. On the contrary, in high TSR range,
drag becomes high. Hence, the short-chord and long-diameter rotor
produces high power coefficient. When a pitch angle at which airfoil
directs toward inside equals to -2° and helical angle equals to 0°,
Darrieus-type VAWT generates maximum power.
Abstract: In this paper, the unstable angle of attack of a
FOXTROT aircraft is controlled by using Genetic Algorithm based
flight controller and the result is compared with the conventional
techniques like Tyreus-Luyben (TL), Ziegler-Nichols (ZN) and
Interpolation Rule (IR) for tuning the PID controller. In addition, the
performance indices like Mean Square Error (MSE), Integral Square
Error (ISE), and Integral Absolute Time Error (IATE) etc. are
improved by using Genetic Algorithm. It was established that the
error by using GA is very less as compared to the conventional
techniques thereby improving the performance indices of the
dynamic system.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: The aim of our study is to project an optimized wind turbine of Darrieus type. This type of wind turbine is characterized by a low starting torque in comparison with the Savonius rotor allowing them to operate for a period greater than wind speed. This led us to reconsider the Darrieus rotor to optimize a design which will increase its starting torque. The study of a system of monitoring and control of the angle of attack of blade profile, which allows an auto start to wind speeds as low as possible is presented for the straight blade of Darrieus turbine. The study continues to extend to other configurations namely those of parabolic type.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: Comprehensive numerical studies have been carried
out to examine the best aerodynamic performance of subsonic aircraft
at different winglet cant angles using a validated 3D k-ω SST model.
In the parametric analytical studies NACA series of airfoils are
selected. Basic design of the winglet is selected from the literature
and flow features of the entire wing including the winglet tip effects
have been examined with different cant angles varying from 150 to
600 at different angles of attack up to 140. We have observed, among
the cases considered in this study that a case, with 150 cant angle the
aerodynamics performance of the subsonic aircraft during takeoff
was found better up to an angle of attack of 2.80 and further its
performance got diminished at higher angles of attack. Analyses
further revealed that increasing the winglet cant angle from 150 to 600
at higher angles of attack could negate the performance deterioration
and additionally it could enhance the peak CL/CD on the order of
3.5%. The investigated concept of variable-cant-angle winglets
appears to be a promising alternative for improving the aerodynamic
efficiency of aircraft.
Abstract: This study involves numerical simulation of the flow
around a NACA2415 airfoil, with a 18° angle of attack, and flow
separation control using a rod, It involves putting a cylindrical rod -
upstream of the leading edge- in vertical translation movement in
order to accelerate the transition of the boundary layer by interaction
between the rod wake and the boundary layer. The viscous, nonstationary
flow is simulated using ANSYS FLUENT 13. The rod
movement is reproduced using the dynamic mesh technique and an
in-house developed UDF (User Define Function). The frequency
varies from 75 to 450 Hz and the considered amplitudes are 2%, and
3% of the foil chord. The frequency chosen closed to the frequency
of separation. Our results showed a substantial modification in the
flow behavior and a maximum drag reduction of 61%.
Abstract: This study involves a numerical simulation of the flow around a NACA2415 airfoil, with a 15°angle of attack, and flow separation control using a rod, It reposes inputting a cylindrical rod upstream of the leading edge in order to accelerate the transition of the boundary layer by interaction between the rod wake and the boundary layer. The viscous, non-stationary flow is simulated using ANSYS FLUENT 13. Our results showed a substantial modification in the flow behavior and a maximum drag reduction of 51%.