Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: The realization of current-mode quadrature oscillators
using current controlled current conveyor transconductance
amplifiers (CCCCTAs) and grounded capacitors is presented. The
proposed oscillators can provide 2 sinusoidal output currents with 90º
phase difference. It is enabled non-interactive dual-current control for
both the condition of oscillation and the frequency of oscillation.
High output impedances of the configurations enable the circuit to be
cascaded without additional current buffers. The use of only
grounded capacitors is ideal for integration. The circuit performances
are depicted through PSpice simulations, they show good agreement
to theoretical anticipation.
Abstract: Space-time block code(STBC) has been studied to get
full diversity and full rate in multiple input multiple output(MIMO)
system. Achieving full rate is difficult in cooperative communications
due to the each user consumes the time slots for transmitting
information in cooperation phase. So combining MIMO systems
with cooperative communications has been researched for full diversity
and full rate. In orthogonal frequency division multiple access
(OFDMA) system, it is an alternative way that each user shares their
allocated subchannels instead of using the MIMO system to improve
the transmission rate. In this paper, a Decode-and-forward (DF)
based cooperative communication scheme is proposed. The proposed
scheme has improved transmission rate and reliability in multi-path
fading channel of the OFDMA up-link condition by modified STBC
structure and subchannel sharing.
Abstract: Wireless Sensor Networks (WSNs) are used to monitor/observe vast inaccessible regions through deployment of large number of sensor nodes in the sensing area. For majority of WSN applications, the collected data needs to be combined with geographic information of its origin to make it useful for the user; information received from remote Sensor Nodes (SNs) that are several hops away from base station/sink is meaningless without knowledge of its source. In addition to this, location information of SNs can also be used to propose/develop new network protocols for WSNs to improve their energy efficiency and lifetime. In this paper, range free localization protocols for WSNs have been proposed. The proposed protocols are based on weighted centroid localization technique, where the edge weights of SNs are decided by utilizing fuzzy logic inference for received signal strength and link quality between the nodes. The fuzzification is carried out using (i) Mamdani, (ii) Sugeno, and (iii) Combined Mamdani Sugeno fuzzy logic inference. Simulation results demonstrate that proposed protocols provide better accuracy in node localization compared to conventional centroid based localization protocols despite presence of unintentional radio frequency interference from radio frequency (RF) sources operating in same frequency band.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. ANSYS software has been used on the proposed model to
find the natural frequencies by Block Lanczos technique and
displacements and dynamic stresses by transient mode super position
method. The effect of rotational speed of the gear on the dynamic
response of gear tooth has been studied and design limits have been
discussed.
Abstract: The charge-pump circuit is an important component in a phase-locked loop (PLL). The charge-pump converts Up and Down signals from the phase/frequency detector (PFD) into current. A conventional CMOS charge-pump circuit consists of two switched current sources that pump charge into or out of the loop filter according to two logical inputs. The mismatch between the charging current and the discharging current causes phase offset and reference spurs in a PLL. We propose a new charge-pump circuit to reduce the current mismatch by using a regulated cascode circuit. The proposed charge-pump circuit is designed and simulated by spectre with TSMC 0.18-μm 1.8-V CMOS technology.
Abstract: The case study deals with the semi-quantitative risk
assessment of water resource earmarked for the emergency supply
of population with drinking water. The risk analysis has been based
on previously identified hazards/sensitivities of the elements
of hydrogeological structure and technological equipment of ground
water resource as well as on the assessment of the levels of hazard,
sensitivity and criticality of individual resource elements in the form
of point indexes. The following potential sources of hazard have
been considered: natural disasters caused by atmospheric and
geological changes, technological hazards, and environmental
burdens. The risk analysis has proved that the assessed risks are
acceptable and the water resource may be integrated into a crisis plan
of a given region.
Abstract: Worldwide many electrical equipment insulation
failures have been reported caused by switching operations, while
those equipments had previously passed all the standard tests and
complied with all quality requirements. The problem is mostly
associated with high-frequency overvoltages generated during
opening or closing of a switching device. The transients generated
during switching operations in a Gas Insulated Substation (GIS) are
associated with high frequency components in the order of few tens
of MHz.
The frequency spectrum of the VFTO generated in the 220/66 kV
Wadi-Hoff GIS is analyzed using Fast Fourier Transform technique.
The main frequency with high voltage amplitude due to the operation
of disconnector (DS5) is 5 to 10 MHz, with the highest amplitude at 9
MHz. The main frequency with high voltage amplitude due to the
operation of circuit breaker (CB5) is 1 to 25 MHz, with the highest
amplitude at 2 MHz.
Mitigating techniques damped the oscillating frequencies
effectively. The using of cable terminal reduced the frequency
oscillation effectively than that of OHTL terminal. The using of a
shunt capacitance results in vanishing the high frequency
components. Ferrite rings reduces the high frequency components
effectively especially in the range 2 to 7 MHz. The using of RC and
RL filters results in vanishing the high frequency components.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: The governing two-dimensional equations of a heterogeneous material composed of a fluid (allowed to flow in the absence of acoustic excitations) and a crystalline piezoelectric cubic solid stacked one-dimensionally (along the z direction) are derived and special emphasis is given to the discussion of acoustic group velocity for the structure as a function of the wavenumber component perpendicular to the stacking direction (being the x axis). Variations in physical parameters with y are neglected assuming infinite material homogeneity along the y direction and the flow velocity is assumed to be directed along the x direction. In the first part of the paper, the governing set of differential equations are derived as well as the imposed boundary conditions. Solutions are provided using Hamilton-s equations for the wavenumber vs. frequency as a function of the number and thickness of solid layers and fluid layers in cases with and without flow (also the case of a position-dependent flow in the fluid layer is considered). In the first part of the paper, emphasis is given to the small-frequency case. Boundary conditions at the bottom and top parts of the full structure are left unspecified in the general solution but examples are provided for the case where these are subject to rigid-wall conditions (Neumann boundary conditions in the acoustic pressure). In the second part of the paper, emphasis is given to the general case of larger frequencies and wavenumber-frequency bandstructure formation. A wavenumber condition for an arbitrary set of consecutive solid and fluid layers, involving four propagating waves in each solid region, is obtained again using the monodromy matrix method. Case examples are finally discussed.
Abstract: Diabetes mellitus (DM) is frequently characterized by
autonomic nervous dysfunction. Analysis of heart rate variability
(HRV) has become a popular noninvasive tool for assessing the
activities of autonomic nervous system (ANS). In this paper, changes
in ANS activity are quantified by means of frequency and time
domain analysis of R-R interval variability. Electrocardiograms
(ECG) of 16 patients suffering from DM and of 16 healthy volunteers
were recorded. Frequency domain analysis of extracted normal to
normal interval (NN interval) data indicates significant difference in
very low frequency (VLF) power, low frequency (LF) power and
high frequency (HF) power, between the DM patients and control
group. Time domain measures, standard deviation of NN interval
(SDNN), root mean square of successive NN interval differences
(RMSSD), successive NN intervals differing more than 50 ms (NN50
Count), percentage value of NN50 count (pNN50), HRV triangular
index and triangular interpolation of NN intervals (TINN) also show
significant difference between the DM patients and control group.
Abstract: In the paper the study of synthetic transmit aperture
method applying the Golay coded transmission for medical
ultrasound imaging is presented. Longer coded excitation allows to
increase the total energy of the transmitted signal without increasing
the peak pressure. Moreover signal-to-noise ratio and penetration
depth are improved while maintaining high ultrasound image
resolution. In the work the 128-element linear transducer array with
0.3 mm inter-element spacing excited by one cycle and the 8 and 16-
bit Golay coded sequences at nominal frequency 4 MHz was used. To
generate a spherical wave covering the full image region a single
element transmission aperture was used and all the elements received
the echo signals. The comparison of 2D ultrasound images of the
tissue mimicking phantom and in vitro measurements of the beef liver
is presented to illustrate the benefits of the coded transmission. The
results were obtained using the synthetic aperture algorithm with
transmit and receive signals correction based on a single element
directivity function.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: Data of wave height and wind speed were collected
from three existing oil fields in South China Sea – offshore
Peninsular Malaysia, Sarawak and Sabah regions. Extreme values
and other significant data were employed for analysis. The data were
recorded from 1999 until 2008. The results show that offshore
structures are susceptible to unacceptable motions initiated by wind
and waves with worst structural impacts caused by extreme wave
heights. To protect offshore structures from damage, there is a need
to quantify descriptive statistics and determine spectra envelope of
wind speed and wave height, and to ascertain the frequency content
of each spectrum for offshore structures in the South China Sea
shallow waters using measured time series. The results indicate that
the process is nonstationary; it is converted to stationary process by
first differencing the time series. For descriptive statistical analysis,
both wind speed and wave height have significant influence on the
offshore structure during the northeast monsoon with high mean wind
speed of 13.5195 knots ( = 6.3566 knots) and the high mean wave
height of 2.3597 m ( = 0.8690 m). Through observation of the
spectra, there is no clear dominant peak and the peaks fluctuate
randomly. Each wind speed spectrum and wave height spectrum has
its individual identifiable pattern. The wind speed spectrum tends to
grow gradually at the lower frequency range and increasing till it
doubles at the higher frequency range with the mean peak frequency
range of 0.4104 Hz to 0.4721 Hz, while the wave height tends to
grow drastically at the low frequency range, which then fluctuates
and decreases slightly at the high frequency range with the mean
peak frequency range of 0.2911 Hz to 0.3425 Hz.
Abstract: Mel Frequency Cepstral Coefficient (MFCC) features
are widely used as acoustic features for speech recognition as well
as speaker recognition. In MFCC feature representation, the Mel frequency
scale is used to get a high resolution in low frequency region,
and a low resolution in high frequency region. This kind of processing
is good for obtaining stable phonetic information, but not suitable
for speaker features that are located in high frequency regions. The
speaker individual information, which is non-uniformly distributed
in the high frequencies, is equally important for speaker recognition.
Based on this fact we proposed an admissible wavelet packet based
filter structure for speaker identification. Multiresolution capabilities
of wavelet packet transform are used to derive the new features.
The proposed scheme differs from previous wavelet based works,
mainly in designing the filter structure. Unlike others, the proposed
filter structure does not follow Mel scale. The closed-set speaker
identification experiments performed on the TIMIT database shows
improved identification performance compared to other commonly
used Mel scale based filter structures using wavelets.
Abstract: A New features are extracted and compared to
improve the prediction of protein-protein interactions. The basic idea
is to select and use the best set of features from the Tensor matrices
that are produced by the frequency vectors of the protein sequences.
Three set of features are compared, the first set is based on the
indices that are the most common in the interacting proteins, the
second set is based on the indices that tend to be common in the
interacting and non-interacting proteins, and the third set is
constructed by using random indices. Moreover, three encoding
strategies are compared; that are based on the amino asides polarity,
structure, and chemical properties. The experimental results indicate
that the highest accuracy can be obtained by using random indices
with chemical properties encoding strategy and support vector
machine.
Abstract: This paper describes an efficient hardware implementation of a new technique for interfacing the data exchange between the microprocessor-based systems and the external devices. This technique, based on the use of software/hardware system and a reduced physical address, enlarges the interfacing capacity of the microprocessor-based systems, uses the Direct Memory Access (DMA) to increases the frequency of the new bus, and improves the speed of data exchange. While using this architecture in microprocessor-based system or in computer, the input of the hardware part of our system will be connected to the bus system, and the output, which is a new bus, will be connected to an external device. The new bus is composed of a data bus, a control bus and an address bus. A Xilinx Integrated Software Environment (ISE) 7.1i has been used for the programmable logic implementation.
Abstract: This paper presents a new approach for setting
frequency relays based on the dynamic of power system. A
simplified model of the power system based on the load-frequency
control loop will be developed to be used instead of the complete
model of the power system. The effects of the equipments and their
responses on the frequency variations of the power plant will be
investigated and then a method for adaptive settings of frequency
relays will be explained. The proposed method will be investigated
by analyzing a simplified model of a power plant by MATLAB
software.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: Fast forecasting of stock market prices is very important for
strategic planning. In this paper, a new approach for fast forecasting of
stock market prices is presented. Such algorithm uses new high speed
time delay neural networks (HSTDNNs). The operation of these
networks relies on performing cross correlation in the frequency
domain between the input data and the input weights of neural
networks. It is proved mathematically and practically that the number
of computation steps required for the presented HSTDNNs is less
than that needed by traditional time delay neural networks
(TTDNNs). Simulation results using MATLAB confirm the
theoretical computations.