Abstract: Nowadays, engineering ceramics have significant
applications in different industries such as; automotive, aerospace,
electrical, electronics and even martial industries due to their
attractive physical and mechanical properties like very high hardness
and strength at elevated temperatures, chemical stability, low friction
and high wear resistance. However, these interesting properties plus
low heat conductivity make their machining processes too hard,
costly and time consuming. Many attempts have been made in order
to make the grinding process of engineering ceramics easier and
many scientists have tried to find proper techniques to economize
ceramics' machining processes. This paper proposes a new diamond
plunge grinding technique using ultrasonic vibration for grinding
Alumina ceramic (Al2O3). For this purpose, a set of laboratory
equipments have been designed and simulated using Finite Element
Method (FEM) and constructed in order to be used in various
measurements. The results obtained have been compared with the
conventional plunge grinding process without ultrasonic vibration
and indicated that the surface roughness and fracture strength
improved and the grinding forces decreased.
Abstract: This paper presents the experimental results of silicone rubber polymer insulators for 22 kV systems under salt water dip wheel test based on IEC 62217. Straight shed silicone rubber polymer insulators having leakage distance 685 mm were tested continuously 30,000 cycles. One test cycle includes 4 positions, energized, de-energized, salt water dip and deenergized, respectively. For one test cycle, each test specimen remains stationary for about 40 second in each position and takes 8 second for rotate to next position. By visual observation, sever surface erosion was observed on the trunk near the energized end of tested specimen. Puncture was observed on the upper shed near the energized end. In addition, decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Furthermore, chemical analysis by ATR-FTIR was conducted in order to elucidate the chemical change of tested specimens comparing with new specimen.
Abstract: In an assessment of the extractability of metals in
green liquor dregs from the chemical recovery circuit of semichemical
pulp mill, extractable concentrations of heavy metals in
artificial gastric fluid were between 10 (Ni) and 717 (Zn) times
higher than those in artificial sweat fluid. Only Al (6.7 mg/kg; d.w.),
Ni (1.2 mg/kg; d.w.) and Zn (1.8 mg/kg; d.w.) showed extractability
in the artificial sweat fluid, whereas Al (730 mg/kg; d.w.), Ba (770
mg/kg; d.w.) and Zn (1290 mg/kg; d.w.) showed clear extractability
in the artificial gastric fluid. As certain heavy metals were clearly
soluble in the artificial gastric fluid, the careful handling of this
residue is recommended in order to prevent the penetration of green
liquor dregs across the human gastrointestinal tract.
Abstract: Lycopene, which can be extracted from plants and is
very popular for fruit intake, is restricted for healthy food development
due to its high price. On the other hand, it will get great safety
concerns, especially in the food or cosmetic application, if the raw
material of lycopene is produced by chemical synthesis. In this
project, we provide a key technology to bridge the limitation as
mentioned above. Based on the abundant bioresources of BCRC
(Bioresource Collection and Research Center, Taiwan), a promising
lycopene output will be anticipated by the introduction of fermentation
technology along with industry-related core energy. Our results
showed that addition of tween 80(0.2%) and span 20 produced higher
amount of lycopene. And piperidine, when was added at 48hr to the
cultivation medium, could promote lycopene excretion effectively
also.
Abstract: This paper unifies power optimization approaches in
various energy converters, such as: thermal, solar, chemical, and
electrochemical engines, in particular fuel cells. Thermodynamics
leads to converter-s efficiency and limiting power. Efficiency
equations serve to solve problems of upgrading and downgrading of
resources. While optimization of steady systems applies the
differential calculus and Lagrange multipliers, dynamic optimization
involves variational calculus and dynamic programming. In reacting
systems chemical affinity constitutes a prevailing component of an
overall efficiency, thus the power is analyzed in terms of an active
part of chemical affinity. The main novelty of the present paper in the
energy yield context consists in showing that the generalized heat
flux Q (involving the traditional heat flux q plus the product of
temperature and the sum products of partial entropies and fluxes of
species) plays in complex cases (solar, chemical and electrochemical)
the same role as the traditional heat q in pure heat engines.
The presented methodology is also applied to power limits in fuel
cells as to systems which are electrochemical flow engines propelled
by chemical reactions. The performance of fuel cells is determined by
magnitudes and directions of participating streams and mechanism of
electric current generation. Voltage lowering below the reversible
voltage is a proper measure of cells imperfection. The voltage losses,
called polarization, include the contributions of three main sources:
activation, ohmic and concentration. Examples show power maxima
in fuel cells and prove the relevance of the extension of the thermal
machine theory to chemical and electrochemical systems. The main
novelty of the present paper in the FC context consists in introducing
an effective or reduced Gibbs free energy change between products p
and reactants s which take into account the decrease of voltage and
power caused by the incomplete conversion of the overall reaction.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: In this study, inhibition of Microcystis aeruginosa by
antialgal alleochemical gramine, was studied by analyzing algal
metabolic activity (represented by esterase and total dehydrogenase
activities) and cell ultrastructure (showing morphological and
ultrastructure alterations using transmission electron microscopy and
DNA ladder analysis). After gramine exposure, esterase and total
dehydrogenase activities were increased firstly but decreased later. In
contrast with the controls, the cells exposed to gramine showed
apparent ultrastructure alterations with thylakoids in breakage,
phycobilins in decrease, lipid and cyanophycin granules abundant
firstly but dissolved afterwards, DNA in fragementation. The
occurrence of increase of metabolic activity and specific granules
reflected that the resistance of cellular response to gramine was
initiated. DNA fragementation associated with the increase of
metabolic activity and specific granules hinted that gramine caused M.
aeruginosa cells to initiate some morphotype of programmed cell
death.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: The draw solute separation process in Forward
Osmosis desalination was simulated in Aspen Plus chemical process
modeling software, to estimate the energy consumption and compare
it with other desalination processes, mainly the Reverse Osmosis
process which is currently most prevalent. The electrolytic chemistry
for the system was retrieved using the Elec – NRTL property method
in the Aspen Plus database. Electrical equivalent of energy required
in the Forward Osmosis desalination technique was estimated and
compared with the prevalent desalination techniques.
Abstract: Proteins levels produced by bacteria may be increased
in stressful surroundings, such as in the presence of antibiotics. It
appears that many antimicrobial agents or antibiotics, when used at
low concentrations, have in common the ability to activate or repress
gene transcription, which is distinct from their inhibitory effect.
There have been comparatively few studies on the potential of
antibiotics or natural compounds in nature as a specific chemical
signal that can trigger a variety of biological functions. Therefore,
this study was focusing on the effect of essential oils from
Cymbopogon flexuosus and C. nardus in regulating proteins
production by Bacillus subtilis ATCC 21332. The Minimum
Inhibition Concentrations (MICs) of both essential oils on B. subtilis
were determined by using microdilution assay, resulting 0.2% and
1.56% for each C. flexuosus and C. nardus subsequently. The
bacteria were further exposed to each essential oils at concentration
of 0.01XMIC for 2 days. The proteins were then isolated and
analyzed by sodium dodecyl sulfate polyacrylamide gel
electrophoresis (SDS-PAGE). Protein profile showed that a band
with approximate size of 250 kD was appeared for the treated
bacteria with essential oils. Thus, Bacillus subtilis ATCC 21332 in
stressful condition with the presence of essential oils at low
concentration could induce the protein production.
Abstract: Environmental awareness and depletion of the
petroleum resources are among vital factors that motivate a number
of researchers to explore the potential of reusing natural fiber as an
alternative composite material in industries such as packaging,
automotive and building constructions. Natural fibers are available in
abundance, low cost, lightweight polymer composite and most
importance its biodegradability features, which often called “ecofriendly"
materials. However, their applications are still limited due
to several factors like moisture absorption, poor wettability and large
scattering in mechanical properties. Among the main challenges on
natural fibers reinforced matrices composite is their inclination to
entangle and form fibers agglomerates during processing due to
fiber-fiber interaction. This tends to prevent better dispersion of the
fibers into the matrix, resulting in poor interfacial adhesion between
the hydrophobic matrix and the hydrophilic reinforced natural fiber.
Therefore, to overcome this challenge, fiber treatment process is one
common alternative that can be use to modify the fiber surface
topology by chemically, physically or mechanically technique.
Nevertheless, this paper attempt to focus on the effect of
mercerization treatment on mechanical properties enhancement of
natural fiber reinforced composite or so-called bio composite. It
specifically discussed on mercerization parameters, and natural fiber
reinforced composite mechanical properties enhancement.
Abstract: Within the framework of a method of the information
theory it is offered statistics and probabilistic model for definition of
cause-and-effect relations in the coupled multicomponent
subsystems. The quantitative parameter which is defined through
conditional and unconditional entropy functions is introduced. The
method is applied to the analysis of the experimental data on
dynamics of change of the chemical elements composition of plants
organs (roots, reproductive organs, leafs and stems). Experiment is
directed on studying of temporal processes of primary soil formation
and their connection with redistribution dynamics of chemical
elements in plant organs. This statistics and probabilistic model
allows also quantitatively and unambiguously to specify the
directions of the information streams on plant organs.
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: To investigate effect of salt stress on Chlorophyll
fluorescence four cultivars (fong,star,chamran and kharchia) of wheat
(Triticum aestivum) plants subjected to salinity levels ( control,8,12
and 16 dsm-1 ) from one week after emergence to the end of stem
elongation under greenhouse condition . results showed that quantum
yield of photosystem II from light adopted leaves (ΦPSII),
Photochemical quenching (qP) ,quantum yield of dark adopted leaves
(fv/fm) and non photochemical quenching (NPq) were affected by
salt stress . Salinity levels affected photosynthetic rate. Star and fong
cultivars showed minimum and maximum levels of photosynthetic
rate in respectively. Minimum photosynthetic rate differences
between levels of salinity were shown in Kharchia. Shoot dry matter
of all cultivars decreased by increasing salinity levels. Results
showed that non photochemical quenching by salinity levels attribute
to the decreases in shoot dry matter.
Abstract: The hydromagnetic flow of a Maxwell fluid past a vertical stretching sheet with thermophoresis is considered. The impact of chemical reaction species to the flow is analyzed for the first time by using the homotopy analysis method (HAM). The h-curves for the flow boundary layer equations are presented graphically. Several values of wall skin friction, heat and mass transfer are obtained and discussed.
Abstract: In the present research, steam cracking of two types of
feedstocks i.e., naphtha and ethane is simulated for Pyrocrack1-1 and
2/2 coil configurations considering two key parameters of coil outlet
temperature (COT) and coil capacity using a radical based kinetic
model. The computer model is confirmed using the industrial data
obtained from Amirkabir Petrochemical Complex. The results are in
good agreement with performance data for naphtha cracking in a
wide range of severity (0.4-0.7), and for ethane cracking on various
conversions (50-70). It was found that Pyrocrack2-2 coil type is an
appropriate choice for steam cracking of ethane at reasonable
ethylene yield while resulting in much lower tube wall temperature
while Pyrocrack1-1 coil type is a proper selection for liquid
feedstocks i.e. naphtha. It can be used for cracking of liquid
feedstocks at optimal ethylene yield whereas not exceeding the
allowable maximum tube temperature.
Abstract: Thailand is the agriculture country as the weather and geography are suitable for agriculture environment. In 2011, the quantity of exported fresh vegetable was 126,069 tons which valued 117.1 million US dollars. Although the fresh vegetable has a high potential in exporting, there also have a lack of knowledge such as chemical usage, land usage, marketing and also the transportation and logistics. Nakorn Pathom province is the area which the farmer and manufacturer of fresh vegetable located. The objectives of this study are to study the basic information of the local fresh vegetable farmers in Nakorn Pathom province, to study the factor which effects the management of the fresh vegetable supply chain in Nakorn Pathom province and to study the problems and obstacle of the fresh vegetable supply chain in Nakorn Pathom province. This study is limited to the flow of the Nakorn Pathom province fresh vegetable from the farmers to the country which import the vegetable from Thailand. The populations of this study are 100 local farmers in Nakorn Pathom province. The result of this study shows that the key process of the fresh vegetable supply chain is in the supply sourcing process and manufacturing process.
Abstract: Biochemical Oxygen Demand (BOD) is a measure of
the oxygen used in bacteria mediated oxidation of organic substances
in water and wastewater. Theoretically an infinite time is required for
complete biochemical oxidation of organic matter, but the
measurement is made over 5-days at 20 0C or 3-days at 27 0C test
period with or without dilution. Researchers have worked to further
reduce the time of measurement.
The objective of this paper is to review advancement made in
BOD measurement primarily to minimize the time and negate the
measurement difficulties. Survey of literature review in four such
techniques namely BOD-BARTTM, Biosensors, Ferricyanidemediated
approach, luminous bacterial immobilized chip method.
Basic principle, method of determination, data validation and their
advantage and disadvantages have been incorporated of each of the
methods.
In the BOD-BARTTM method the time lag is calculated for the
system to change from oxidative to reductive state. BIOSENSORS
are the biological sensing element with a transducer which produces
a signal proportional to the analyte concentration. Microbial species
has its metabolic deficiencies. Co-immobilization of bacteria using
sol-gel biosensor increases the range of substrate. In ferricyanidemediated
approach, ferricyanide has been used as e-acceptor instead
of oxygen. In Luminous bacterial cells-immobilized chip method,
bacterial bioluminescence which is caused by lux genes was
observed. Physiological responses is measured and correlated to
BOD due to reduction or emission.
There is a scope to further probe into the rapid estimation of BOD.