Abstract: The storage of chemical fertilizers in concrete building often leads to durability problems due to chemical attack. The damage of concrete is mostly caused by certain ammonium salts. The main purpose of the research is to investigate the durability properties of concrete being exposed to ammonium nitrate solution. In this investigation, experiments are conducted on concrete type G50 and G60. The leaching process is achieved by the use of 20% concentration solution of ammonium nitrate. The durability properties investigated are water absorption, volume of permeable voids, and sorptivity. Compressive strength, pH value, and degradation depth are measured after a certain period of leaching. A decrease in compressive strength and an increase in porosity are found through the conducted experiments. Apart from that, the experimental data shows that pH value decreases with increased leaching time while the degradation depth of concrete increases with leaching time. By comparing concrete type G50 and G60, concrete type G60 is more resistant to ammonium nitrate attack.
Abstract: New design of a grid for preparation of high density
granules with enhanced mechanical strength by granulation of
dispersed materials is suggested.
A method for hydrodynamic dimensioning of the grid depending
on granulation conditions, hydrodynamic regime of the operation,
dispersity and physicochemical characteristics of the materials to be
granulated was suggested.
The aim of the grid design is to solve the problems arising by the
granulation of disperse materials.
Abstract: The validity of Herzberg-s Two-Factor Theory of
Motivation was tested empirically by surveying 2372 chemical fiber
employees in 2012. In the valid sample of 1875 respondents, the
degree of overall job satisfaction was more than moderate. The most
highly valued components of job satisfaction were: “corporate image,"
“collaborative working atmosphere," and “supervisor-s expertise";
whereas the lowest mean score was 34.65 for “job rotation and
promotion." The top three job retention options rated by the
participants were “good image of the enterprise," “good
compensation," and “workplace is close to my residence." The overall
evaluation of the level of thriving facilitation workplace reached
almost to “mostly agree." For those participants who chose at least
one motivator as their job retention options had significantly greater
job satisfaction than those who chose only hygiene factors as their
retention options. Therefore, Herzberg-s Two-Factor Theory of
Motivation was proven valid in this study.
Abstract: fifteen cultivars of Strawberries (Queen Eliza, Sequia,
Paros, Mcdonance, Selva, Chandler, Mrak, Ten beauty, Aliso, Pajero,
Kordestan, Camarosa, Blackmore, Gaviota and Fresno) were
investigated in 2011, under hydroponic system condition. Yield and
fruit Firmness was determinate. Chemical analyses of soluble solids
content (SSC), titratable acidity (TA), ascorbic acid (AA) and pH
were done. 4 cultivars (Aliso, Selva, Paros and Gaviota) yielded more
than 250 g/plant, while cultivar Black more, Fresno and Kordestan
produced less than 100g/plant. The amounts of fruit firmness
indicated that 'Camarosa' fruit was firmer than others cultivars.
Cultivar 'Fresno' had the highest pH (3.27). Ttitratable acidity varied
from 1.03g/l00g for cultivar 'Sequia' and 'Gaviota' to 1.48g/l00g for
cultivar 'Chandler'. Fresno, Kordestan, Aliso and Chandler showed
the highest soluble solid concentration. Ascorbic acid averaged for
most cultivars between 30.26 and 79.73 mg/100gf.w. Present results
showed that different cultivars of strawberry contain highly variable
in fruit quality.
Abstract: The nature of adsorbed species on catalytic surface
over an industrial precipitated iron-based high temperature catalyst
during FTS was investigated by in-situ DRIFTS and chemical
trapping. The formulation of the mechanism of oxygenates formation
and key intermediates were also discussed. Numerous oxygenated
precursors and crucial intermediates were found by in-situ DRIFTS,
such as surface acetate, acetyl and methoxide. The results showed that
adsorbed molecules on surface such as methanol or acetaldehyde
could react with basic sites such as lattice oxygen or free surface
hydroxyls. Adsorbed molecules also had reactivity of oxidizing.
Moreover, acetyl as a key intermediate for oxygenates was observed
by investigation of CH3OH + CO and CH3I + CO + H2. Based on the
nature of surface properties, the mechanism of oxygenates formation
on precipitated iron-based high temperature catalyst was discussed.
Abstract: This study has investigated the antidiabetic and
antioxidant potential of Pseudovaria macrophylla bark extract on
streptozotocin–nicotinamide induced type 2 diabetic rats. LCMSQTOF
and NMR experiments were done to determine the chemical
composition in the methanolic bark extract. For in vivo experiments,
the STZ (60 mg/kg/b.w, 15 min after 120 mg/kg/1 nicotinamide, i.p.)
induced diabetic rats were treated with methanolic extract of
Pseuduvaria macrophylla (200 and 400 mg/kg·bw) and
glibenclamide (2.5 mg/kg) as positive control respectively.
Biochemical parameters were assayed in the blood samples of all
groups of rats. The pro-inflammatory cytokines, antioxidant status
and plasma transforming growth factor βeta-1 (TGF-β1) were
evaluated. The histological study of the pancreas was examined and
its expression level of insulin was observed by
immunohistochemistry. In addition, the expression of glucose
transporters (GLUT 1, 2 and 4) were assessed in pancreas tissue by
western blot analysis. The outcomes of the study displayed that the
bark methanol extract of Pseuduvaria macrophylla has potentially
normalized the elevated blood glucose levels and improved serum
insulin and C-peptide levels with significant increase in the
antioxidant enzyme, reduced glutathione (GSH) and decrease in the
level of lipid peroxidation (LPO). Additionally, the extract has
markedly decreased the levels of serum pro-inflammatory cytokines
and transforming growth factor beta-1 (TGF-β1). Histopathology
analysis demonstrated that Pseuduvaria macrophylla has the
potential to protect the pancreas of diabetic rats against peroxidation
damage by downregulating oxidative stress and elevated
hyperglycaemia. Furthermore, the expression of insulin protein,
GLUT-1, GLUT-2 and GLUT-4 in pancreatic cells was enhanced.
The findings of this study support the anti-diabetic claims of
Pseudovaria macrophylla bark.
Abstract: Raman spectroscopy are used to characterize the
chemical changes in normoxic polyhydroxyethylacrylate gel
dosimeter (PHEA) induced by radiation. Irradiations in the low dose
region are performed and the polymerizations of PHEA gels are
monitored by the observing the changes of Raman shift intensity of
the carbon covalent bond of PHEA originated from both monomer
and the cross-linker. The variation in peak intensities with absorbed
dose was observed. As the dose increase, the peak intensities of
covalent bond of carbon in the polymer gels decrease. This point out
that the amount of absorbed dose affect the polymerization of
polymer gels. As the absorbed dose increase, the polymerizations
also increase. Results verify that PHEA gel dosimeters are sensitive
even in lower dose region.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: Renewable energy sources have gained ultimate urgency due to the need of the preservation of the environment for a sustainable development. Pyrolysis is an ultimate promising process in the recycling and acquisition of precious chemicals from wastes. Here, the co-pyrolysis of hazelnut shell with ultra-high molecular weight polyethylene was carried out catalytically and noncatalytically at 500 and 650 ºC. Potassium dichromate was added in certain amounts to act as a catalyst. The liquid, solid and gas products quantities were determined by gravimetry. As a main result, remarkable increases in gasification were observed by using this catalyst for pure components and their blends especially at 650 ºC. The increase in gas product quantity was compensated mainly with the decreases in the solid products and additionally in some cases liquid products quantities. These observations may stem from mainly the activation of carbon-carbon bonds rather than carbon-hydrogen bonds via potassium dichromate. Also, the catalytic effect of potassium dichromate on HS: PEO and HS: UHMWPE co-pyrolysis was compared.
Abstract: There are several means to measure the oxidation of edible oils, such as the acid value, the peroxide value, and the anisidine value. However, these means require large quantities of reagents and are time-consuming tasks. Therefore, a more convenient and time-saving way to measure the oxidation of edible oils is required. In this report, an edible oil condition sensor was fabricated by using single-walled nanotubes (SWNT). In order to test the sensor, oxidized edible oils, each one at a different acid value, were prepared. The SWNT sensors were immersed into these oxidized oils and the resistance changes in the sensors were measured. It was found that the conductivity of the sensors decreased as the oxidation level of oil increased. This result suggests that a change of the oil components induced by the oxidation process in edible oils is related to the conductivity change in the SWNT sensor.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: Explosion occurs due to sudden release of energy.
Common examples of explosion include chemical, atomic, heat, and
pressure tank (due to ignition) explosions. Petroleum, gas, and
petrochemical industries operations are threatened by natural risks
and processes. Fires and explosions are the greatest process risks
which cause financial damages.
This study aims at designing a single-floor structure for the control
room of a petroleum refinery to be resistant against gas explosion
loads, and the information related to the structure specifications have
been provided regarding the fact that the structure is made on the
ground's surface. In this research, the lateral stiffness of single pile is
calculated by SPPLN.FOR computer program, and its value for
13624 KN/m single pile has been assessed. The analysis used due to
the loading conditions, is dynamic nonlinear analysis with direct
integration method.
Abstract: Silver nanoparticles were prepared by chemical reduction method. Silver nitrate was taken as the metal precursor and hydrazine hydrate as a reducing agent. The formation of the silver nanoparticles was monitored using UV-Vis absorption spectroscopy. The UV-Vis spectroscopy revealed the formation of silver nanopart├¡cles by exhibing the typical surface plasmon absorption maxima at 418-420 nm from the UV–Vis spectrum. Comparison of theoretical (Mie light scattering theory) and experimental results showed that diameter of silver nanoparticles in colloidal solution is about 60 nm. We have used energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and, UV–Vis spectroscopy to characterize the nanoparticles obtained. The energy-dispersive spectroscopy (EDX) of the nanoparticles dispersion confirmed the presence of elemental silver signal no peaks of other impurity were detected. The average size and morphology of silver nanoparticles were determined by transmission electron microscopy (TEM). TEM photographs indicate that the nanopowders consist of well dispersed agglomerates of grains with a narrow size distribution (40 and 60 nm), whereas the radius of the individual particles are between 10 and 20 nm. The synthesized nanoparticles have been structurally characterized by X-ray diffraction and transmission high-energy electron diffraction (HEED). The peaks in the XRD pattern are in good agreement with the standard values of the face-centered-cubic form of metallic silver (ICCD-JCPDS card no. 4-0787) and no peaks of other impurity crystalline phases were detected. Additionally, the antibacterial activity of the nanopart├¡culas dispersion was measured by Kirby-Bauer method. The nanoparticles of silver showed high antimicrobial and bactericidal activity against gram positive bacteria such as Escherichia Coli, Pseudimonas aureginosa and staphylococcus aureus which is a highly methicillin resistant strain.
Abstract: Ciprofloxacin (CIP) and Carbamazepine (CBZ), nonbiodegradable pharmaceutical residues, were become emerging pollutants in several aquatic environments. The objectives of this research were to study the possibility to recover these pharmaceuticals residues from pharmaceutical wastewater by increasing the selective adsorption on synthesized functionalized porous silicate, comparing with powdered activated carbon (PAC). Hexagonal mesoporous silicate (HMS), functionalized HMSs (3- aminopropyltriethoxy, 3- mercaptopropyltrimethoxy and noctyldimethyl) were synthesized and characterized physico-chemical characteristics. Obtained adsorption kinetics and isotherms showed that 3-mercaptopropyltrimethoxy functional groups grafted on HMS provided highest CIP and CBZ adsorption capacities; however, it was still lower than that of PAC. The kinetic results were compatible with pseudo-second order. The hydrophobicity and hydrogen bonding might play a key role on the adsorption. Furthermore, the capacities were affected by varying pH values due to the strength of hydrogen bonding between targeted compounds and adsorbents. Electrostatic interaction might not affect the adsorption capacities.
Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: Extracellular ubiquitin in vivo effect on regenerative liver cells and liver histoarchitectonics has been studied. Experiments were performed on mature female white rats. Partial hepatectomy was made using the modified method of Higgins and Anderson. Standard histopathological assessment of liver tissue was used. Proliferative activity of hepatocytes was analyzed by colchicine mitotic index and immunohistochemical staining on ki67. We have found that regardless of number of injections and dose of extracellular ubiquitin liver histology has not been changed, so at tissue level no effect was observed. In vivo double injection of ubiquitin significantly decreases the mitotic activity at 32 hour point after partial hepatectomy. Thus, we can conclude that in vivo injected extracellular ubiquitin inhibits proliferative activity of hepatocytes in partially hepatectomyzed rats.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.