Abstract: The enzyme alkaline protease production was determined under
solid state fermentation using the soil bacteria Serratia marcescens
sp7. The maximum production was obtained from wheat bran
medium than ground nut shell and chemically defined medium. The
physiological fermentation factors such as pH of the medium (pH 8),
Temperature (40oC) and incubation time (48 hrs) played a vital role
in alkaline protease production in all the above. 100Mm NaCl has
given better resolution during elution of the enzymes. The enzyme
production was found to be associated with growth of the bacterial
culture.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: In this research, several physical and chemical properties and mineral contents of Russion olive (Elaeagnus angustifolia L.) fruit grown in Turkey were determined. In the fruit, length, width, thickness, weight were determined as 2.866cm, 1.880cm, 1.870cm, 2.90g; total soluble solids and colour were determined as 13.14% and S33O60Y99, respectively. In the seed, mean length, width, thickness, and weight were found to be 2.420cm, 0.508cm, 0.503cm, and 0.38g, respectively. In the fruit, 28 minerals (K, P, Ca, Na, Mg, S, Pb, Ba, Ga, As, In, Ti, Fe, Mn, Zn, Cu, Co, B, Cd, Se, Li, Sr, Al, Ni, Ag, V, Cr, Bi) were analyzed and 19 minerals were present at detectable levels. Russion olive fruit was richest in potassium (10296.906ppm), Mg (762.314ppm), P (609.694ppm), Ca (547.647ppm), and Na (222.749ppm).
Abstract: A unique combination of adsorption and
electrochemical regeneration with a proprietary adsorbent material
called Nyex 100 was introduced at the University of Manchester for
waste water treatment applications. Nyex 100 is based on graphite
intercalation compound. It is non porous and electrically conducing
adsorbent material. This material exhibited very small BET surface
area i.e. 2.75 m2g-1, in consequence, small adsorptive capacities for
the adsorption of various organic pollutants were obtained. This work
aims to develop composite adsorbent material essentially capable of
electrochemical regeneration coupled with improved adsorption
characteristics. An organic dye, acid violet 17 was used as standard
organic pollutant. The developed composite material was
successfully electrochemically regenerated using a DC current of 1 A
for 60 minutes. Regeneration efficiency was maintained at around
100% for five adsorption-regeneration cycles.
Abstract: The stem cells have ability to differentiated
themselves through mitotic cell division and various range of
specialized cell types. Cellular differentiation is a way by which few
specialized cell develops into more specialized.This paper studies the
fundamental problem of computational schema for an artificial neural
network based on chemical, physical and biological variables of
state. By doing this type of study system could be model for a viable
propagation of various economically important stem cells
differentiation. This paper proposes various differentiation outcomes
of artificial neural network into variety of potential specialized cells
on implementing MATLAB version 2009. A feed-forward back
propagation kind of network was created to input vector (five input
elements) with single hidden layer and one output unit in output
layer. The efficiency of neural network was done by the assessment
of results achieved from this study with that of experimental data
input and chosen target data. The propose solution for the efficiency
of artificial neural network assessed by the comparatative analysis of
“Mean Square Error" at zero epochs. There are different variables of
data in order to test the targeted results.
Abstract: Polyurethane foams (PUF) were formed by a chemical
reaction of polyol and isocyanate. The polyol was manufactured by
ring-opening hydrolysis of epoxidized soybean oil in the presence of
phosphoric acid under varying experimental conditions. Other
factors in the foam formulation such as water content and surfactant
were kept constant. The effect of the amount of solvents, phosphoric
acid, and their derivates in the foam formulation on the properties of
polyurethane foams were studied. The properties of the material were
measured via a number of parameters, which are water content of
prepared polyol, polymer density and cellular structures.
Abstract: This work presents a low-cost and eco-friendly
building material named Agrostone panel. Africa-s urban population
is growing at an annual rate of 2.8% and 62% of its population will
live in urban areas by 2050. As a consequence, many of the least
urbanized and least developed African countries- will face serious
challenges in providing affordable housing to the urban dwellers.
Since the cost of building materials accounts for the largest
proportion of the overall construction cost, innovating low-cost
building material is vital. Agrostone panel is used in housing projects
in Ethiopia. It uses raw materials of agricultural/industrial wastes
and/or natural minerals as a filler, magnesium-based chemicals as a
binder and fiberglass as reinforcement. Agrostone panel reduces the
cost of wall construction by 50% compared with the conventional
building materials. The pros and cons of Agrostone panel as well as
the use of other waste materials as a raw material to make the panel
more sustainable, low-cost and better properties are discussed.
Abstract: Among the chemicals used for ammunition production, TNT (Trinitrotoluene) play a significant role since World War I and II. Various types of military weapon utilize TNT in casting process. However, the TNT casting process for warhead is difficult to control the cooling rate of the liquid TNT. This problem occurs because the casting process lacks the equipment to detect the temperature during the casting procedure This study presents the temperature detected by infrared camera to illustrate the cooling rate and cooling zone of curing, and demonstrates the optimization of TNT condition to reduce the risk of air gap occurred in the warhead which can result in the destruction afterward. Premature initiation of explosive-filled projectiles in response to set-back forces during gunfiring cause by casting defects. Finally the study can help improving the process of the TNT casting. The operators can control the curing of TNT inside the case by rising up the heating rod at the proper time. Consequently this can reduce tremendous time of rework if the air gaps occur and increase strength to lower elastic modulus. Therefore, it can be clearly concluded that the use of Infrared Cameras in this process is another method to improve the casting procedure.
Abstract: Self-compacting concrete (SCC), a new kind of high
performance concrete (HPC) have been first developed in Japan in
1986. The development of SCC has made casting of dense
reinforcement and mass concrete convenient, has minimized noise.
Fresh self-compacting concrete (SCC) flows into formwork and
around obstructions under its own weight to fill it completely and
self-compact (without any need for vibration), without any
segregation and blocking. The elimination of the need for
compaction leads to better quality concrete and substantial
improvement of working conditions. SCC mixes generally have a
much higher content of fine fillers, including cement, and produce
excessively high compressive strength concrete, which restricts its
field of application to special concrete only. To use SCC mixes in
general concrete construction practice, requires low cost materials to
make inexpensive concrete.
Rice husk ash (RHA) has been used as a highly reactive
pozzolanic material to improve the microstructure of the interfacial
transition zone (ITZ) between the cement paste and the aggregate in
self compacting concrete. Mechanical experiments of RHA blended
Portland cement concretes revealed that in addition to the pozzolanic
reactivity of RHA (chemical aspect), the particle grading (physical
aspect) of cement and RHA mixtures also exerted significant
influences on the blending efficiency.
The scope of this research was to determine the usefulness of Rice
husk ash (RHA) in the development of economical self compacting
concrete (SCC). The cost of materials will be decreased by reducing
the cement content by using waste material like rice husk ash instead
of.
This paper presents a study on the development of Mechanical
properties up to 180 days of self compacting and ordinary concretes
with rice-husk ash (RHA), from a rice paddy milling industry in
Rasht (Iran). Two different replacement percentages of cement by
RHA, 10%, and 20%, and two different water/cementicious material
ratios (0.40 and 0.35), were used for both of self compacting and
normal concrete specimens. The results are compared with those of
the self compacting concrete without RHA, with compressive,
flexural strength and modulus of elasticity. It is concluded that RHA
provides a positive effect on the Mechanical properties at age after
60 days.
Base of the result self compacting concrete specimens have higher
value than normal concrete specimens in all test except modulus of
elasticity. Also specimens with 20% replacement of cement by RHA
have the best performance.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Five vegetables (spinach, lettuce, cabbage, tomato, and onion) were freshly harvested from the Alau Dam and Gongulong agricultural areas for the determination of some organochlorine pesticide residues (o, p-DDE, p,p’-DDD, o,p’-DDD, p,p’-DDT, α-BHC, γ-BHC, metoxichlor, lindane, endosulfan dieldrin, and aldrin.) Soil samples were also collected at different depths for the determination of the above pesticides. Samples collection and preparation were conducted using standard procedures. The concentrations of all the pesticides in the soil and vegetable samples were determined using GC/MS SHIMADZU (GC-17A) equipped with electron capture detector (ECD). The highest concentration was that of p,p’-DDD (132.4±13.45µg/g) which was observed in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (2.34µg/g) was observed in the root of spinach. Similar trends were observed at the Gongulong agricultural area, with p,p’-DDD having the highest concentration of 153.23µg/g in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (12.45µg/g) which was observed in the root of spinach. α-BHC, γ-BHC, Methoxychlor, and lindane were detected in all the vegetable samples studied. The concentrations of all the pesticides in the soil samples were observed to be higher at a depth of 21-30cm, while the lowest concentrations were observed at a depth of 0-10cm. The concentrations of all the pesticides in the vegetables and soil samples from the two agricultural sites were observed to be at alarming levels, much higher than the maximum residue limits (MRLs) and acceptable daily intake values (ADIs) .The levels of the pesticides observed in the vegetables and soil samples investigated, are of such a magnitude that calls for special attention and laws to regulate the use and circulation of such chemicals. Routine monitoring of pesticide residues in these study areas is necessary for the prevention, control and reduction of environmental pollution, so as to minimize health risks.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: The present article comprises a theoretical study of
structures Performat radical (HCO3) with H2O molecule. We make
use of ab initio quantum chemical methods. Unrestricted Hartee-Fock
(UHF) with the basis set6-311+g(2df,2p) and density functional
theory (B3LYP) with the basis set 6-311+g(2df,2p) and also we done
atoms in molecules (AIM) theory for them. We have found four
stable geometries the PerformatRadical(HCO3) with H2O.
Abstract: This paper reports the three-phase (gas + liquid +
hydrate) equilibrium pressure versus temperature data for a (O3 + O2 +
CO2 + H2O) system for developing the hydrate-based technology to
preserve ozone, a chemically unstable substance, for various
industrial, medical and consumer uses. These data cover the
temperature range from 272 K to 277 K, corresponding to pressures
from 1.6 MPa to 3.1 MPa, for each of the three different (O3 +
O2)-to-CO2 or O2-to-CO2 molar ratios in the gas phase, which are
approximately 4 : 6, 5 : 5, respectively. The mole fraction of ozone in
the gas phase was ~0.03 , which are the densest ozone fraction to
artificially form O3 containing hydrate ever reported in the literature.
Based on these data, the formation of hydrate containing
high-concentration ozone, as high as 1 mass %, will be expected.
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: The Pulsed Compression Reactor promises to be a
compact, economical and energy efficient alternative to conventional
chemical reactors.
In this article, the production of synthesis gas using the Pulsed
Compression Reactor is investigated. This is done experimentally as
well as with simulations. The experiments are done by means of a
single shot reactor, which replicates a representative, single
reciprocation of the Pulsed Compression Reactor with great control
over the reactant composition, reactor temperature and pressure and
temperature history. Simulations are done with a relatively simple
method, which uses different models for the chemistry and
thermodynamic properties of the species in the reactor. Simulation
results show very good agreement with the experimental data, and
give great insight into the reaction processes that occur within the
cycle.
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: Some physico-chemical characteristics and mineral
composition of 'Karayemis' (Prunus laurocerasus L.) fruits which
grown naturally in Norteast Turkey was studied. 28 minerals ( Al,
Mg, B, Mn, Co, Na, Ca, Ni, Cd, P, Cr, Pb, Cu, S, Fe, Zn, K, Sr, Li,
As, V, Ag, Ba, Br, Ga, In, Se, Ti) were analyzed and 19 minerals
were present at ascertainable levels. Karayemis fruit was richest in
potassium (7938.711 ppm), magnesium (1242.186 ppm) and calcium
(1158.853 ppm). And some physico-chemical characteristics of
Karayemis fruit was investigated. Fruit length, fruit width, fruit
thickness, fruit weight, total soluble solids, colour, protein, crude ash,
crude fiber, crude oil values were determined as 2.334 cm, 1.884 cm,
2.112 cm, 5.35 g, 20.1 %, S99M99Y99, 0.29 %, 0.22 %, 6.63 % and
0.001 %, respectively. The seed of fruit mean weight, length, width
and thickness were found to be 0.41 g, 1.303 cm, 0.921 cm and
0.803, respectively.
Abstract: Antimosy-doped tin oxide (ATO) particles were
prepared via chemical coprecipitation and reverse emulsion. The size
and size distribution of ATO particles were obviously decreased via
reverse microemulsion method. At the relatively high yield the ATO
particles were nearly spherical in shape, meanwhile the crystalline
structure and excellent conductivity were reserved, which could satisfy
the requirement as composite fillers, such as dielectric filler of
polyimide film.