Abstract: Non-uniform current distribution in polymer
electrolyte membrane fuel cells results in local over-heating,
accelerated ageing, and lower power output than expected. This
issue is very critical when fuel cell experiences water flooding. In
this work, the performance of a PEM fuel cell is investigated under
cathode flooding conditions. Two-dimensional partially flooded
GDL models based on the conservation laws and electrochemical
relations are proposed to study local current density distributions
along flow fields over a wide range of cell operating conditions.
The model results show a direct association between cathode inlet
humidity increases and that of average current density but the
system becomes more sensitive to flooding. The anode inlet
relative humidity shows a similar effect. Operating the cell at
higher temperatures would lead to higher average current densities
and the chance of system being flooded is reduced. In addition,
higher cathode stoichiometries prevent system flooding but the
average current density remains almost constant. The higher anode
stoichiometry leads to higher average current density and higher
sensitivity to cathode flooding.
Abstract: Turbine blade cooling is considered as the most
effective way of maintaining high operating temperature making use
of the available materials, and turbine systems with wet compression
have a potential for future power generation because of high efficiency
and high specific power with a relatively low cost. In this paper
performance analysis of wet-compression gas turbine cycle with
turbine blade cooling is carried out. The wet compression process is
analytically modeled based on non-equilibrium droplet evaporation.
Special attention is paid for the effects of pressure ratio and water
injection ratio on the important system variables such as ratio of
coolant fluid flow, fuel consumption, thermal efficiency and specific
power. Parametric studies show that wet compression leads to
insignificant improvement in thermal efficiency but significant
enhancement of specific power in gas turbine systems with turbine
blade cooling.
Abstract: Humic acids (HAs) have been shown to activate some
ion uptakes along with stimulating the lateral roots at effective
concentration of micronutrients. However, the effects of HA on ion
adsorption by plant roots are not easily explainable due to the
varieties of HAs that differ from origins. Therefore, this study was
aimed to investigate the effect of various concentrations of HA
obtained from the compost derived from mix manures and some
agricultural wastes on the growth of eggplant seedlings (Solanum
melongena L. cv. Chao Praya) in tissue cultures at low nutrient level.
Egg plant seeds were surfaced sterilized and germinated in ½
Murashige and Skoog medium (MS) without HA added or in ¼ MS
supplemented with 0, 25, 50, 75 and 100 ppm of HAs. Then, they
were cultured for 4 weeks under the controlled environment. The
results showed that seedlings grown on ¼MS supplemented with
HAs at the concentration of 25 and 50 ppm had the average plant
heights (2.49 and 2.28 cm, respectively) higher than the other
treatments. Both treatments also significantly showed the maximum
average fresh and dry weights (p
Abstract: A mobile ad hoc network is a network of mobile nodes
without any notion of centralized administration. In such a network,
each mobile node behaves not only as a host which runs applications
but also as a router to forward packets on behalf of others. Clustering
has been applied to routing protocols to achieve efficient
communications. A CH network expresses the connected relationship
among cluster-heads. This paper discusses the methods for
constructing a CH network, and produces the following results: (1)
The required running costs of 3 traditional methods for constructing a
CH network are not so different from each other in the static
circumstance, or in the dynamic circumstance. Their running costs in
the static circumstance do not differ from their costs in the dynamic
circumstance. Meanwhile, although the routing costs required for the
above 3 methods are not so different in the static circumstance, the
costs are considerably different from each other in the dynamic
circumstance. Their routing costs in the static circumstance are also
very different from their costs in the dynamic circumstance, and the
former is one tenths of the latter. The routing cost in the dynamic
circumstance is mostly the cost for re-routing. (2) On the strength of
the above results, we discuss new 2 methods regarding whether they
are tolerable or not in the dynamic circumstance, that is, whether the
times of re-routing are small or not. These new methods are revised
methods that are based on the traditional methods. We recommended
the method which produces the smallest routing cost in the dynamic
circumstance, therefore producing the smallest total cost.
Abstract: We present a discussion of three adaptive filtering
algorithms well known for their one-step termination property, in
terms of their relationship with the minimal residual method. These
algorithms are the normalized least mean square (NLMS), Affine
Projection algorithm (APA) and the recursive least squares algorithm
(RLS). The NLMS is shown to be a result of the orthogonality
condition imposed on the instantaneous approximation of the Wiener
equation, while APA and RLS algorithm result from orthogonality
condition in multi-dimensional minimal residual formulation. Further
analysis of the minimal residual formulation for the RLS leads to
a triangular system which also possesses the one-step termination
property (in exact arithmetic)
Abstract: Fuzzy controllers are potential candidates for the
control of nonlinear, time variant and also complicated systems. Anti
lock brake system (ABS) which is a nonlinear system, may not be
easily controlled by classical control methods. An intelligent Fuzzy
control method is very useful for this kind of nonlinear system. A
typical antilock brake system (ABS) by sensing the wheel lockup,
releases the brakes for a short period of time, and then reapplies again
the brakes when the wheel spins up. In this paper, an intelligent fuzzy
ABS controller is designed to adjust slipping performance for variety
of roads. There are tow major sections in the proposing control
system. First section consists of tow Fuzzy-Logic Controllers (FLC)
providing optimal brake torque for both front and rear wheels.
Second section which is also a FLC provides required amount of slip
and torque references properties for different kind of roads.
Simulation results of our proposed intelligent ABS for three different
kinds of road show more reliable and better performance in compare
with two other break systems.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: In the present investigation, H13 tool steel has been
deposited on copper alloy substrate using both CO2 and diode laser.
A detailed parametric analysis has been carried out in order to find
out optimum processing zone for coating defect free H13 tool steel
on copper alloy substrate. Followed by parametric optimization, the
microstructure and microhardness of the deposited clads have been
evaluated. SEM micrographs revealed dendritic microstructure in
both clads. However, the microhardness of CO2 laser deposited clad
was much higher compared to diode laser deposited clad.
Abstract: To determine the length of engagement threads of a bolt installed in a tapped part in order to avoid the threads stripping remains a very current problem in the design of the thread assemblies. It does not exist a calculation method formalized for the cases where the bolt is screwed directly in a ductile material. In this article, we study the behavior of the threads stripping of a loaded assembly by using a modelling by finite elements and a rupture criterion by damage. This modelling enables us to study the different parameters likely to influence the behavior of this bolted connection. We study in particular, the influence of couple of materials constituting the connection, of the bolt-s diameter and the geometrical characteristics of the tapped part, like the external diameter and the length of engagement threads. We established an experiments design to know the most significant parameters. That enables us to propose a simple expression making possible to calculate the resistance of the threads whatever the metallic materials of the bolt and the tapped part. We carried out stripping tests in order to validate our model. The estimated results are very close to those obtained by the tests.
Abstract: In this paper an analysis of blackouts in electric power
transmission systems is implemented using a model and studied in
simple networks with a regular topology. The proposed model
describes load demand and network improvements evolving on a
slow timescale as well as the fast dynamics of cascading overloads
and outages.
Abstract: In the stadium structure, the significant dynamic
responses such as resonance or similar behavior can be occurred by
spectator rhythmical activities. Thus, accurate analysis and precise
investigation of stadium structure that is subjected to dynamic loads
are required for practical design and serviceability check of stadium
structures. Moreover, it is desirable to measure and analyze the
dynamic loads of spectator activities because these dynamic loads can
not be easily expressed in numerical formula. In this study, various
dynamic loads induced by spectator movements are measured and
analyzed. These dynamic loads induced by spectators movement of
stadium structure can be classified into the impact load and the
periodic load. These dynamic loads can be expressed as Fourier
harmonic load. And, these dynamic loads could be applied for the
accurate vibration analysis of a stadium structure.
Abstract: For fire safety purposes, the fire resistance and the
structural behavior of reinforced concrete members are assessed to
satisfy specific fire performance criteria. The available prescribed
provisions are based on standard fire load. Under various fire
scenarios, engineers are in need of both heat transfer analysis and
structural analysis. For heat transfer analysis, the study proposed a
modified finite difference method to evaluate the temperature profile
within a cross section. The research conducted is limited to concrete
sections exposed to a fire on their one side. The method is based on
the energy conservation principle and a pre-determined power
function of the temperature profile. The power value of 2.7 is found
to be a suitable value for concrete sections. The temperature profiles
of the proposed method are only slightly deviate from those of the
experiment, the FEM and the FDM for various fire loads such as
ASTM E 119, ASTM 1529, BS EN 1991-1-2 and 550 oC. The
proposed method is useful to avoid incontinence of the large matrix
system of the typical finite difference method to solve the
temperature profile. Furthermore, design engineers can simply apply
the proposed method in regular spreadsheet software.
Abstract: The volume of XML data exchange is explosively increasing, and the need for efficient mechanisms of XML data management is vital. Many XML storage models have been proposed for storing XML DTD-independent documents in relational database systems. Benchmarking is the best way to highlight pros and cons of different approaches. In this study, we use a common benchmarking scheme, known as XMark to compare the most cited and newly proposed DTD-independent methods in terms of logical reads, physical I/O, CPU time and duration. We show the effect of Label Path, extracting values and storing in another table and type of join needed for each method's query answering.
Abstract: The elimimation of mefenamic acid has been carried
out by photolysis, ozonation, adsorption onto activated carbon (AC)
and combinations of the previous single systems (O3+AC and
O3+UV). The results obtained indicate that mefenamic acid is not
photo-reactive, showing a relatively low quantum yield of the order
of 6 x 10-4 mol Einstein-1. Application of ozone to mefenamic
aqueous solutions instantaneously eliminates the pharmaceutical,
achieving simultaneously a 40% of mineralization. Addition of AC to
the ozonation process does not enhance the process, moreover,
mineralization is completely inhibited if compared to results obtained
by single ozonation. The combination of ozone and UV radiation led
to the best results in terms of mineralization (60% after 120 min).
Abstract: The impact of noise upon live quality has become an
important aspect to make both urban and environmental policythroughout
Europe and in Turkey. Concern over the quality of urban
environments, including noise levels and declining quality of green
space, is over the past decade with increasing emphasis on designing
livable and sustainable communities. According to the World Health
Organization, noise pollution is the third most hazardous
environmental type of pollution which proceeded by only air (gas
emission) and water pollution. The research carried out in two
phases, the first stage of the research noise and plant types providing
the suction of noise was evaluated through literature study and at the
second stage, definite types (Juniperus horizontalis L., Spirea
vanhouetti Briot., Cotoneaster dammerii C.K., Berberis thunbergii
D.C., Pyracantha coccinea M. etc.) were selected for the city of
Konya. Trials were conducted on the highway of Konya. The biggest
value of noise reduction was 6.3 dB(A), 4.9 dB(A), 6.2 dB(A) value
with compared to the control which includes the group that formed
by the bushes at the distance of 7m, 11m, 20m from the source and
5m, 9m, 20m of plant width, respectively. In this paper, definitions
regarding to noise and its sources were made and the precautions
were taken against to noise that mentioned earlier with the adverse
effects of noise. Plantation design approaches and suggestions
concerning to the diversity to be used, which are peculiar to roadside,
were developed to discuss the role and the function of plant material
to reduce the noise of the traffic.
Abstract: The flow field over a three dimensional pole barn
characterized by a cylindrical roof has been numerically investigated.
Wind pressure and viscous loads acting on the agricultural building
have been analyzed for several incoming wind directions, so as to
evaluate the most critical load condition on the structure. A constant
wind velocity profile, based on the maximum reference wind speed in
the building site (peak gust speed worked out for 50 years return
period) and on the local roughness coefficient, has been simulated.
In order to contemplate also the hazard due to potential air
wedging between the stored hay and the lower part of the ceiling, the
effect of a partial filling of the barn has been investigated.
The distribution of wind-induced loads on the structure have been
determined, allowing a numerical quantification of the effect of wind
direction on the induced stresses acting on a hemicylindrical roof.
Abstract: This paper presents a generalization kernel for gravitational
potential determination by harmonic splines. It was shown
in [10] that the gravitational potential can be approximated using a
kernel represented as a Newton integral over the real Earth body. On
the other side, the theory of geopotential approximation by harmonic
splines uses spherically oriented kernels. The purpose of this paper
is to show that in the spherical case both kernels have the same type
of representation, which leads us to conclusion that it is possible
to consider the kernel represented as a Newton integral over the real
Earth body as a kind of generalization of spherically harmonic kernels
to real geometries.