Abstract: The application of a Static Synchronous Series Compensator (SSSC) controller to improve the transient stability performance of a power system is thoroughly investigated in this paper. The design problem of SSSC controller is formulated as an optimization problem and Particle Swarm Optimization (PSO) Technique is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor angle of the generator is involved; transient stability performance of the system is improved. The proposed controller is tested on a weakly connected power system subjected to different severe disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and its ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC controller improves greatly the voltage profile of the system under severe disturbances.
Abstract: The objective of this paper is to study the analysis and testing for determining the torsional stiffness of the student formula-s space frame. From past study, the space frame for Chulalongkorn University Student Formula team used in 2011 TSAE Auto Challenge Student Formula in Thailand was designed by considering required mass and torsional stiffness based on the numerical method and experimental method. The numerical result was compared with the experimental results to verify the torsional stiffness of the space frame. It can be seen from the large error of torsional stiffness of 2011 frame that the experimental result can not verify by the numerical analysis due to the different between the numerical model and experimental setting. In this paper, the numerical analysis and experiment of the same 2011 frame model is performed by improving the model setting. The improvement of both numerical analysis and experiment are discussed to confirm that the models from both methods are same. After the frame was analyzed and tested, the results are compared to verify the torsional stiffness of the frame. It can be concluded that the improved analysis and experiments can used to verify the torsional stiffness of the space frame.
Abstract: Since the actuator capacity is limited, in the real
application of active control systems under sever earthquakes it is
conceivable that the actuators saturate, hence the actuator saturation
should be considered as a constraint in design of optimal controllers.
In this paper optimal design of active controllers for nonlinear
structures by considering actuator saturation, has been studied. The
proposed method for designing optimal controllers is based on
defining an optimization problem which the objective has been to
minimize the maximum displacement of structure when a limited
capacity for actuator has been used. To this end a single degree of
freedom (SDF) structure with a bilinear hysteretic behavior has been
simulated under a white noise ground acceleration of different
amplitudes. Active tendon control mechanism, comprised of prestressed
tendons and an actuator, and extended nonlinear Newmark
method based instantaneous optimal control algorithm have been
used. To achieve the best results, the weights corresponding to
displacement, velocity, acceleration and control force in the
performance index have been optimized by the Distributed Genetic
Algorithm (DGA). Results show the effectiveness of the proposed
method in considering actuator saturation. Also based on the
numerical simulations it can be concluded that the actuator capacity
and the average value of required control force are two important
factors in designing nonlinear controllers which consider the actuator
saturation.
Abstract: This paper presents a comparative study on two most
popular control strategies for Permanent Magnet Synchronous Motor
(PMSM) drives: field-oriented control (FOC) and direct torque
control (DTC). The comparison is based on various criteria including
basic control characteristics, dynamic performance, and
implementation complexity. The study is done by simulation using
the Simulink Power System Blockset that allows a complete
representation of the power section (inverter and PMSM) and the
control system. The simulation and evaluation of both control
strategies are performed using actual parameters of Permanent
Magnet Synchronous Motor fed by an IGBT PWM inverter.
Abstract: This paper describes various stages of design and prototyping of a modular robot for use in various industrial applications. The major goal of current research has been to design and make different robotic joints at low cost capable of being assembled together in any given order for achieving various robot configurations. Five different types of joins were designed and manufactured where extensive research has been carried out on the design of each joint in order to achieve optimal strength, size, modularity, and price. This paper presents various stages of research and development undertaken to engineer these joints that include material selection, manufacturing, and strength analysis. The outcome of this research addresses the birth of a new generation of modular industrial robots with a wider range of applications and greater efficiency.
Abstract: The service sector continues to grow and the percentage
of GDP accounted for by service industries keeps increasing. The
growth and importance of service to an economy is not just a
phenomenon of advanced economies, service is now a majority of the
world gross domestic products. However, the performance evaluation
process of new service development problems generally involves
uncertain and imprecise data. This paper presents a 2-tuple fuzzy
linguistic computing approach to dealing with heterogeneous
information and information loss problems while the processes of
subjective evaluation integration. The proposed method based on group
decision-making scenario to assist business managers in measuring
performance of new service development manipulates the
heterogeneity integration processes and avoids the information loss
effectively.
Abstract: Time delay in bilateral teleoperation system was
introduced as a sufficient reason to make the system unstable or
certainly degrade the system performance. In this paper, simulations
and experimental results of implementing p-like control scheme,
under different ranges of variable time delay, will be presented to
verify a certain criteria, which guarantee the system stability and
position tracking. The system consists of two Phantom premium 1.5A
devices. One of them acts as a master and the other acts as a slave.
The study includes deriving the Phantom kinematic and dynamic
model, establishing the link between the two Phantoms over
Simulink in Matlab, and verifying the stability criteria with
simulations and real experiments.
Abstract: The present work is concerned with sulfidation of Cu,
Zn and Ni containing plating wastewater with CaS. The sulfidation
experiments were carried out at a room temperature by adding solid
CaS to simulated metal solution containing either single-metal of Ni,
Zn and Cu, or Ni-Zn-Cu mixture. At first, the experiments were
conducted without pH adjustment and it was found that the complete
sulfidation of Zn and Ni was achieved at an equimolar ratio of CaS to a
particular metal. However, in the case of Cu, a complete copper
sulfidation was achieved at CaS to Cu molar ratio of about 2. In the
case of the selective sulfidation, a simulated plating solution
containing Cu, Zn and Ni at the concentration of 100 mg/dm3 was
treated with CaS under various pH conditions. As a result, selective
precipitation of metal sulfides was achieved by a sulfidation treatment
at different pH values. Further, the precipitation agents of NaOH,
Na2S and CaS were compared in terms of the average specific
filtration resistance and compressibility coefficients of metal sulfide
slurry. Consequently, based on the lowest filtration parameters of the
produced metal sulfides, it was concluded that CaS was the most
effective precipitation agent for separation and recovery of Cu, Zn and
Ni.
Abstract: Today, numerical simulation is a powerful tool to
solve various hydraulic engineering problems. The aim of this
research is numerical solutions of shallow water equations using
finite volume method for Simulations of dam break over wet and dry
bed. In order to solve Riemann problem, Roe-s approximate solver is
used. To evaluate numerical model, simulation was done in 1D and
2D states. In 1D state, two dam break test over dry bed (with and
without friction) were studied. The results showed that Structural
failure around the dam and damage to the downstream constructions
in bed without friction is more than friction bed. In 2D state, two
tests for wet and dry beds were done. Generally in wet bed case,
waves are propagated to canal sides but in dry bed it is not
significant. Therefore, damage to the storage facilities and
agricultural lands in wet bed case is more than in dry bed.
Abstract: In this study a neural network (NN) was proposed to
predict the sorption of binary mixture of copper-cobalt ions into
clinoptilolite as ion-exchanger. The configuration of the
backpropagation neural network giving the smallest mean square
error was three-layer NN with tangent sigmoid transfer function at
hidden layer with 10 neurons, linear transfer function at output layer
and Levenberg-Marquardt backpropagation training algorithm.
Experiments have been carried out in the batch reactor to obtain
equilibrium data of the individual sorption and the mixture of coppercobalt
ions. The obtained modeling results have shown that the used
of neural network has better adjusted the equilibrium data of the
binary system when compared with the conventional sorption
isotherm models.
Abstract: These This paper looks into frameworks which aim at
furthering the discussion of the role of regenerative design practices
in a city-s historic core and the tool of urban design to achieve urban
revitalization on the island of Cyprus. It also examines the region-s
demographic mix, the effectiveness of its governmental coordination
and the strategies of adaptive reuse and strategic investments in older
areas with existing infrastructure. The two main prongs of
investigation will consider the effect of the existing and proposed
changes in the physical infrastructure and fabric of the city, as well as
the catalytic effect of sustainable urban design practices. Through this
process, the work hopes to integrate the contained potential within
the existing historic core and the contributions and participation of
the migrant and immigrant populations to the local economy. It also
examines ways in which this coupling of factors can bring to the front
the positive effects of this combined effort on an otherwise sluggish
local redevelopment effort. The data for this study is being collected
and organized as part of ongoing urban design and development
student workshop efforts in urban planning and design education.
The work is presented in graphic form and includes data collected
from interviews with study area organizations and the community at
large. Planning work is also based on best practices initiated by the
staff of the Nicosia Master Plan task force, which coordinates holistic
planning efforts for the historic center of the city of Nicosia.
Abstract: As current business environment is demanding a
constant adaptation of companies, the planning and strategic
management should be an ongoing and natural process in all kind of
organizations. The use of management and monitoring strategic
performance tools such as the Balanced Scorecard (BSC) have been
popular; even to Small and Medium-sized Enterprises. This paper
aims to investigate whether the BSC is being used in monitoring the
performance of small businesses, particularly in small fuel retailers
companies, which are competing in co-branding; and if not, it aims to
identify its strategic orientation in order to recommend a possible
strategy map for those managers that are willing to adopt this model
as an alternative to traditional ones for organizational performance
evaluation, which often focus only on evaluation of the
organizational financial performance.
Abstract: The paper is concerned with developing stochastic delay mechanisms for efficient multicast protocols and for smooth mobile handover processes which are capable of preserving a given Quality of Service (QoS). In both applications the participating entities (receiver nodes or subscribers) sample a stochastic timer and generate load after a random delay. In this way, the load on the networking resources is evenly distributed which helps to maintain QoS communication. The optimal timer distributions have been sought in different p.d.f. families (e.g. exponential, power law and radial basis function) and the optimal parameter have been found in a recursive manner. Detailed simulations have demonstrated the improvement in performance both in the case of multicast and mobile handover applications.
Abstract: The main purpose of this research was to analyze Socio-Cultural obstacles of disseminating of nanotechnology in Iran's agricultural section. One hundred twenty eight out of a total of 190 researchers with different levels of expertise in and familiarity with nanotechnology were randomly selected and questionnaires completed by them. Face validity have been done by expert's suggestion and correction, reliability by using Cronbakh-Alpha formula. The results of a factor analysis showed variation for different factors. For cultural factors 19/475 percent, for management 13/139 percent, information factor 11/277 percent, production factor 9/703 percent, social factor 9/267 percent, and for attitude factor it became 8/947 percent. Also results indicated that socio-cultural factors were the most important obstacle for nanotechnology dissemination in agricultural section in Iran.
Abstract: In this paper, we have combined some spatial derivatives with the optimised time derivative proposed by Tam and Webb in order to approximate the linear advection equation which is given by = 0. Ôêé Ôêé + Ôêé Ôêé x f t u These spatial derivatives are as follows: a standard 7-point 6 th -order central difference scheme (ST7), a standard 9-point 8 th -order central difference scheme (ST9) and optimised schemes designed by Tam and Webb, Lockard et al., Zingg et al., Zhuang and Chen, Bogey and Bailly. Thus, these seven different spatial derivatives have been coupled with the optimised time derivative to obtain seven different finite-difference schemes to approximate the linear advection equation. We have analysed the variation of the modified wavenumber and group velocity, both with respect to the exact wavenumber for each spatial derivative. The problems considered are the 1-D propagation of a Boxcar function, propagation of an initial disturbance consisting of a sine and Gaussian function and the propagation of a Gaussian profile. It is known that the choice of the cfl number affects the quality of results in terms of dissipation and dispersion characteristics. Based on the numerical experiments solved and numerical methods used to approximate the linear advection equation, it is observed in this work, that the quality of results is dependent on the choice of the cfl number, even for optimised numerical methods. The errors from the numerical results have been quantified into dispersion and dissipation using a technique devised by Takacs. Also, the quantity, Exponential Error for Low Dispersion and Low Dissipation, eeldld has been computed from the numerical results. Moreover, based on this work, it has been found that when the quantity, eeldld can be used as a measure of the total error. In particular, the total error is a minimum when the eeldld is a minimum.
Abstract: Stainless steel has been employed in many
engineering applications ranging from pharmaceutical equipment to
piping in the nuclear reactors and storage to chemical products. In
this attempt, simulation of fatigue crack growth based on
experimental results of austenitic stainless steel 304L was presented
using AFGROW code when NASGRO mode laws adopted. Double
through crack at hole specimen is used in this investigation under
constant amplitude loading. Effect of mean stress is highlighted.
Results show that fatigue crack growth rate (FCGR) and fatigue life
were affected by maximum applied load and dimension of hole. An
equivalent of Paris law for this material was estimated.
Abstract: An unstructured finite volume numerical model is
presented here for simulating shallow-water flows with wetting and
drying fronts. The model is based on the Green-s theorem in
combination with Chorin-s projection method. A 2nd-order upwind
scheme coupled with a Least Square technique is used to handle
convection terms. An Wetting and drying treatment is used in the
present model to ensures the total mass conservation. To test it-s
capacity and reliability, the present model is used to solve the
Parabolic Bowl problem. We compare our numerical solutions with
the corresponding analytical and existing standard numerical results.
Excellent agreements are found in all the cases.
Abstract: This paper presents a low cost design of heart beat monitoring device using reflectance mode PhotoPlethysmography (PPG). PPG is known for its simple construction, ease of use and cost effectiveness and can provide information about the changes in cardiac activity as well as aid in earlier non-invasive diagnostics. The proposed device is divided into three phases. First is the detection of pulses through the fingertip. The signal is then passed to the signal processing unit for the purpose of amplification, filtering and digitizing. Finally the heart rate is calculated and displayed on the computer using parallel port interface. The paper is concluded with prototyping of the device followed by verification procedure of the heartbeat signal obtained in laboratory setting.
Abstract: The optimal control problem for the viscoelastic melt
spinning process has not been reported yet in the literature. In this
study, an optimal control problem for a mathematical model of a
viscoelastic melt spinning process is considered. Maxwell-Oldroyd
model is used to describe the rheology of the polymeric material, the
fiber is made of. The extrusion velocity of the polymer at the spinneret
as well as the velocity and the temperature of the quench air and the
fiber length serve as control variables. A constrained optimization
problem is derived and the first–order optimality system is set up
to obtain the adjoint equations. Numerical solutions are carried out
using a steepest descent algorithm. A computer program in MATLAB
is developed for simulations.
Abstract: To identify an endothelial cell-specific promoter suitable for vascular-specific targeting, we tested five promoters in vitro--Tie2SE, Tie2LE, ICAM2, Flt-1 and vWF--for promoter activity and specificity in endothelial cells, smooth muscle cells and non-vascular resident cells as well as tissues. These promoters, except for vWF, exhibited good endothelial activity and specificity in vitro. In a syngenic heart transplantation model, the ICAM2 promoter was variably functional in coronary endothelial cells of donor hearts. Thus, the ICAM2, Flt-1, Tie2SE and Tie2LE promoters hold promise for endothelial-specific targeting, but in vitro expression may not predict in vivo expression.