Abstract: Data of wave height and wind speed were collected
from three existing oil fields in South China Sea – offshore
Peninsular Malaysia, Sarawak and Sabah regions. Extreme values
and other significant data were employed for analysis. The data were
recorded from 1999 until 2008. The results show that offshore
structures are susceptible to unacceptable motions initiated by wind
and waves with worst structural impacts caused by extreme wave
heights. To protect offshore structures from damage, there is a need
to quantify descriptive statistics and determine spectra envelope of
wind speed and wave height, and to ascertain the frequency content
of each spectrum for offshore structures in the South China Sea
shallow waters using measured time series. The results indicate that
the process is nonstationary; it is converted to stationary process by
first differencing the time series. For descriptive statistical analysis,
both wind speed and wave height have significant influence on the
offshore structure during the northeast monsoon with high mean wind
speed of 13.5195 knots ( = 6.3566 knots) and the high mean wave
height of 2.3597 m ( = 0.8690 m). Through observation of the
spectra, there is no clear dominant peak and the peaks fluctuate
randomly. Each wind speed spectrum and wave height spectrum has
its individual identifiable pattern. The wind speed spectrum tends to
grow gradually at the lower frequency range and increasing till it
doubles at the higher frequency range with the mean peak frequency
range of 0.4104 Hz to 0.4721 Hz, while the wave height tends to
grow drastically at the low frequency range, which then fluctuates
and decreases slightly at the high frequency range with the mean
peak frequency range of 0.2911 Hz to 0.3425 Hz.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: SQL injection on web applications is a very popular
kind of attack. There are mechanisms such as intrusion detection
systems in order to detect this attack. These strategies often rely on
techniques implemented at high layers of the application but do not
consider the low level of system calls. The problem of only
considering the high level perspective is that an attacker can
circumvent the detection tools using certain techniques such as URL
encoding. One technique currently used for detecting low-level
attacks on privileged processes is the tracing of system calls. System
calls act as a single gate to the Operating System (OS) kernel; they
allow catching the critical data at an appropriate level of detail. Our
basic assumption is that any type of application, be it a system
service, utility program or Web application, “speaks” the language of
system calls when having a conversation with the OS kernel. At this
level we can see the actual attack while it is happening. We conduct
an experiment in order to demonstrate the suitability of system call
analysis for detecting SQL injection. We are able to detect the attack.
Therefore we conclude that system calls are not only powerful in
detecting low-level attacks but that they also enable us to detect highlevel
attacks such as SQL injection.
Abstract: A genetic algorithm (GA) based feature subset
selection algorithm is proposed in which the correlation structure of
the features is exploited. The subset of features is validated according
to the classification performance. Features derived from the
continuous wavelet transform are potentially strongly correlated.
GA-s that do not take the correlation structure of features into
account are inefficient. The proposed algorithm forms clusters of
correlated features and searches for a good candidate set of clusters.
Secondly a search within the clusters is performed. Different
simulations of the algorithm on a real-case data set with strong
correlations between features show the increased classification
performance. Comparison is performed with a standard GA without
use of the correlation structure.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: A novel design of two-wheeled robotic vehicle with moving payload is presented in this paper. A mathematical model describing the vehicle dynamics is derived and simulated in Matlab Simulink environment. Two control strategies were developed to stabilise the vehicle in the upright position. A robust Proportional- Integral-Derivative (PID) control strategy has been implemented and initially tested to measure the system performance, while the second control strategy is to use a hybrid fuzzy logic controller (FLC). The results are given on a comparative basis for the system performance in terms of disturbance rejection, control algorithms robustness as well as the control effort in terms of input torque.
Abstract: In this paper, linear multistep technique using power
series as the basis function is used to develop the block methods
which are suitable for generating direct solution of the special second
order ordinary differential equations of the form y′′ = f(x,y), a < = x < = b with associated initial or boundary conditions. The continuaous hybrid formulations enable us to differentiate and evaluate at some
grids and off – grid points to obtain two different three discrete
schemes, each of order (4,4,4)T, which were used in block form for
parallel or sequential solutions of the problems. The computational
burden and computer time wastage involved in the usual reduction of
second order problem into system of first order equations are avoided
by this approach. Furthermore, a stability analysis and efficiency of
the block method are tested on linear and non-linear ordinary
differential equations whose solutions are oscillatory or nearly
periodic in nature, and the results obtained compared favourably with
the exact solution.
Abstract: The work reported in this paper is motivated by the fact that there is a need to apply autonomic computing concepts to parallel computing systems. Advancing on prior work based on intelligent cores [36], a swarm-array computing approach, this paper focuses on 'Intelligent agents' another swarm-array computing approach in which the task to be executed on a parallel computing core is considered as a swarm of autonomous agents. A task is carried to a computing core by carrier agents and is seamlessly transferred between cores in the event of a predicted failure, thereby achieving self-ware objectives of autonomic computing. The feasibility of the proposed swarm-array computing approach is validated on a multi-agent simulator.
Abstract: Participation in global trade means that Chinas vegetables and fruits industry faces international food safety standards and increased scrutiny worldwide. The objectives of this paper were to investigate how existing food safety standards and regulations in the importing countries impact the export of vegetables and fruits from China. This paper discussed the current and historical situations of Chinas vegetables and fruits export from 1996 to 2010, analyzed the Maximum Residual Limit (MRL) standards of pesticides imposed by importing countries, quantitatively estimated the impacts of food safety standards on Chinas vegetables and fruits export based on a gravity model. The results showed that although transportation distance between trade partners and tariff rates on vegetables and fruits were still the importantly resistant factors for China export, vegetables and fruits export was sensitive to the number of regulated pesticides, the strictness, and the level of food safety standards imposed by importing countries, which showed a significant trade flow effect, stricter food safety standards, increased number of regulated pesticides significantly inhibit China export of vegetables and fruits. Moreover, Chinas food safety standards also showed a significantly effect on vegetables and fruits export, which inhibited export to some extent. KeywordsFood safety standards, MRL, Vegetables, Fruits, Export.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: In this paper, the Lennard -Jones potential is applied
to molecules of liquid argon as well as its vapor and platinum as solid
surface in order to perform a non-equilibrium molecular dynamics
simulation to study the microscopic aspects of liquid-vapor-solid
interactions. The channel is periodic in x and y directions and along z
direction it is bounded by atomic walls. It was found that density of
the liquids near the solid walls fluctuated greatly and that the
structure was more like a solid than a liquid. This indicates that the
interactions of solid and liquid molecules are very strong. The
resultant surface tension, liquid density and vapor density are found
to be well predicted when compared with the experimental data for
argon. Liquid and vapor densities were found to depend on the cutoff
radius which induces the use of P3M (particle-particle particle-mesh)
method which was implemented for evaluation of force and surface
tension.
Abstract: This paper presents a novel approach to finding a
priori interesting regions in mammograms. In order to delineate those
regions of interest (ROI-s) in mammograms, which appear to be
prominent, a topographic representation called the iso-level contour
map consisting of iso-level contours at multiple intensity levels and
region segmentation based-thresholding have been proposed. The
simulation results indicate that the computed boundary gives the
detection rate of 99.5% accuracy.
Abstract: Networked schools have become a feature of
education systems in countries that seek to provide learning
opportunities in schools located beyond major centres of population.
The internet and e-learning have facilitated the development of
virtual educational structures that complement traditional schools,
encouraging collaborative teaching and learning to proceed. In rural
New Zealand and in the Atlantic Canadian province of
Newfoundland and Labrador, e-learning is able to provide new ways
of organizing teaching, learning and the management of educational
opportunities. However, the future of e-teaching and e-learning in
networked schools depends on the development of professional
education programs that prepare teachers for collaborative teaching
and learning environments in which both virtual and traditional face
to face instruction co-exist.
Abstract: Forty-five dairy cows were used to compare the
enzyme activity of alkaline phosphatase (ALP), lactate
dehydrogenase (LDH), α -amylase in the cervical mucus of cows
during spontaneous and induced estrus using progestagen or PGF2 α
and to determine whether these enzymes affect the fertility in cows
with induced estrus, at the time of Al. The animals were assigned to 3
groups (no treatment, a Crestar® for 12 days, a double im injection of
PGF2 α). The cows were artificially inseminated (AI). Cervical
mucus samples were collected from all cows 3 to 5 min before the
AI. The results are summarized as follows: ALP and α -amylase
activity for spontaneous estrus were similar to those for induced
estrus (P>0.05) . LDH activity levels during spontaneous and PGF2 α
induced estrus was significantly lower (P < 0.001) than that in
progestagene induced estrus groups. While no difference was found
between the first and the third groups. Our result showed a significant
difference in LDH activity levels between cows conceived with 2 or
more AI and those conceived with 1 AI. The result of this study
showed that the enzyme activity in cervical mucus is helpful for
detection of ovulation and time of AI.
Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: Adaptive Genetic Algorithms extend the Standard Gas
to use dynamic procedures to apply evolutionary operators such as
crossover, mutation and selection. In this paper, we try to propose a
new adaptive genetic algorithm, which is based on the statistical
information of the population as a guideline to tune its crossover,
selection and mutation operators. This algorithms is called Statistical
Genetic Algorithm and is compared with traditional GA in some
benchmark problems.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.