Abstract: In this paper, we present a method named Signal Level
Matrix (SLM) which can improve the accuracy and stability of active
RFID indoor positioning system. Considering the accuracy and cost,
we use uniform distribution mode to set up and separate the
overlapped signal covering areas, in order to achieve preliminary
location setting. Then, based on the proposed SLM concept and the
characteristic of the signal strength value that attenuates as the
distance increases, this system cross-examines the distribution of
adjacent signals to locate the users more accurately. The experimental
results indicate that the adaptive positioning method proposed in this
paper could improve the accuracy and stability of the positioning
system effectively and satisfyingly.
Abstract: This paper presents part of a research into the small
scale modelling of masonry. Small scale testing of masonry has been
carried out by many authors, but few have attempted a systematic
determination of the parameters that affect masonry at a small scale.
The effect of increasing mortar strength and different sand gradings
under compression were investigated. The results show masonry
strength at small scale is influenced by increasing mortar strength and
different sand gradings.
Abstract: The design of high-rise building is more often dictated
by its serviceability rather than strength. Structural Engineers are
always striving to overcome challenge of controlling lateral
deflection and storey drifts as well as self weight of structure
imposed on foundation.
One of the most effective techniques is the use of outrigger and
belt truss system in Composite structures that can astutely solve the
above two issues in High-rise constructions.
This paper investigates deflection control by effective utilisation
of belt truss and outrigger system on a 60-storey composite building
subjected to wind loads. A three dimensional Finite Element Analysis
is performed with one, two and three outrigger levels. The reductions
in lateral deflection are 34%, 42% and 51% respectively as compared
to a model without any outrigger system. There is an appreciable
decline in the storey drifts with the introduction of these stiffer
arrangements.
Abstract: The paper investigates the feasibility of constructing a software multi-agent based monitoring and classification system and utilizing it to provide an automated and accurate classification of end users developing applications in the spreadsheet domain. The agents function autonomously to provide continuous and periodic monitoring of excels spreadsheet workbooks. Resulting in, the development of the MultiAgent classification System (MACS) that is in compliance with the specifications of the Foundation for Intelligent Physical Agents (FIPA). However, different technologies have been brought together to build MACS. The strength of the system is the integration of the agent technology with the FIPA specifications together with other technologies that are Windows Communication Foundation (WCF) services, Service Oriented Architecture (SOA), and Oracle Data Mining (ODM). The Microsoft's .NET widows service based agents were utilized to develop the monitoring agents of MACS, the .NET WCF services together with SOA approach allowed the distribution and communication between agents over the WWW that is in order to satisfy the monitoring and classification of the multiple developer aspect. ODM was used to automate the classification phase of MACS.
Abstract: The aim of this study was to extract sugar from
sugarcane using high electric field pulse (HELP) as a non-thermal cell permeabilization method. The result of this study showed that it
is possible to permeablize sugar cane cells using HELP at very short times (less than 10 sec.) and at room temperature. Increasing the field strength (from 0.5kV/cm to 2kV/cm) and pulse number (1 to 12) led to increasing the permeabilization of sugar cane cells. The energy
consumption during HELP treatment of sugar cane (2.4 kJ/kg) was about 100 times less compared to thermal cell disintegration at 85
Abstract: Improving the performance of the QCL through block diagram as well as mathematical models is the main scope of this paper. In order to enhance the performance of the underlined device, the mathematical model parameters are used in a reliable manner in such a way that the optimum behavior was achieved. These parameters play the central role in specifying the optical characteristics of the considered laser source. Moreover, it is important to have a large amount of radiated power, where increasing the amount of radiated power represents the main hopping process that can be predicted from the behavior of quantum laser devices. It was found that there is a good agreement between the calculated values from our mathematical model and those obtained with VisSim and experimental results. These demonstrate the strength of mplementation of both mathematical and block diagram models.
Abstract: The objective of this research was to study influence
parameters affecting to mechanical property of austenitic stainless
steel grade 304 (AISI 304) with Gas Metal Arc Welding (GMAW).
The research was applying factorial design experiment, which have
following interested parameters: welding current at 80, 90, and 100
Amps, welding speeds at 250, 300, and 350 mm/min, and shield gas
of 75% Ar + 25% CO2, 70% Ar + 25% CO2 + 5% O2 and 69.5% Ar +
25% CO2 + 5% O2 + 0.5% He gas. The study was done in following
aspects: ultimate tensile strength and elongation. A research study of
ultimate tensile strength found that main factor effect, which had the
highest strength to AISI 304 welding was shield gas of 70% Ar +
25% CO2 + 5% O2 at average of 954.81 N/mm2. Result of the highest
elongation was showed significantly different at interaction effect
between shield gas of 69.5%Ar+25%CO2+5%O2+.5%He and
welding speed at 250 mm/min at 47.94%.
Abstract: A mobile ad hoc network is a network of mobile nodes
without any notion of centralized administration. In such a network,
each mobile node behaves not only as a host which runs applications
but also as a router to forward packets on behalf of others. Clustering
has been applied to routing protocols to achieve efficient
communications. A CH network expresses the connected relationship
among cluster-heads. This paper discusses the methods for
constructing a CH network, and produces the following results: (1)
The required running costs of 3 traditional methods for constructing a
CH network are not so different from each other in the static
circumstance, or in the dynamic circumstance. Their running costs in
the static circumstance do not differ from their costs in the dynamic
circumstance. Meanwhile, although the routing costs required for the
above 3 methods are not so different in the static circumstance, the
costs are considerably different from each other in the dynamic
circumstance. Their routing costs in the static circumstance are also
very different from their costs in the dynamic circumstance, and the
former is one tenths of the latter. The routing cost in the dynamic
circumstance is mostly the cost for re-routing. (2) On the strength of
the above results, we discuss new 2 methods regarding whether they
are tolerable or not in the dynamic circumstance, that is, whether the
times of re-routing are small or not. These new methods are revised
methods that are based on the traditional methods. We recommended
the method which produces the smallest routing cost in the dynamic
circumstance, therefore producing the smallest total cost.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: Chemical and physical functionalization of multiwalled
carbon nanotubes (MWCNT) has been commonly practiced to
achieve better dispersion of carbon nanotubes (CNTs) in polymer
matrix. This work describes various functionalization methods (acidtreatment,
non-ionic surfactant treatment with TritonX-100),
fabrication of MWCNT/PP nanocomposites via melt blending and
characterization of mechanical properties. Microscopy analysis
(FESEM, TEM, XPS) showed effective purification of MWCNTs
under acid treatment, and better dispersion under both chemical and
physical functionalization techniques combined, in their respective
order. Tensile tests showed increase in tensile strength for the
nanocomposites that contain MWCNTs up to 2 wt%. A decrease in
tensile strength was seen in samples that contain 4 wt% of MWCNTs
for both raw and Triton X-100 functionalized, signifying MWCNT
degradation/rebundling at composition with higher content of
MWCNTs. For the acid-treated MWCNTs, however, the tensile
results showed slight improvement even at 4wt%, indicating effective
dispersion of MWCNTs.
Abstract: This report aims to utilize existing and future Multiple-Input Multiple-Output Orthogonal Frequency Division Multiplexing Wireless Local Area Network (MIMO-OFDM WLAN) systems characteristics–such as multiple subcarriers, multiple antennas, and channel estimation characteristics–for indoor location estimation systems based on the Direction of Arrival (DOA) and Radio Signal Strength Indication (RSSI) methods. Hybrid of DOA-RSSI methods also evaluated. In the experimental data result, we show that location estimation accuracy performances can be increased by minimizing the multipath fading effect. This is done using multiple subcarrier frequencies over wideband frequencies to estimate one location. The proposed methods are analyzed in both a wide indoor environment and a typical room-sized office. In the experiments, WLAN terminal locations are estimated by measuring multiple subcarriers from arrays of three dipole antennas of access points (AP). This research demonstrates highly accurate, robust and hardware-free add-on software for indoor location estimations based on a MIMO-OFDM WLAN system.
Abstract: Some quality control tools use non metric subjective information coming from experts, who qualify the intensity of relations existing inside processes, but without quantifying them. In this paper we have developed a quality control analytic tool, measuring the impact or strength of the relationship between process operations and product characteristics. The tool includes two models: a qualitative model, allowing relationships description and analysis; and a formal quantitative model, by means of which relationship quantification is achieved. In the first one, concepts from the Graphs Theory were applied to identify those process elements which can be sources of variation, that is, those quality characteristics or operations that have some sort of prelacy over the others and that should become control items. Also the most dependent elements can be identified, that is those elements receiving the effects of elements identified as variation sources. If controls are focused in those dependent elements, efficiency of control is compromised by the fact that we are controlling effects, not causes. The second model applied adapts the multivariate statistical technique of Covariance Structural Analysis. This approach allowed us to quantify the relationships. The computer package LISREL was used to obtain statistics and to validate the model.
Abstract: In recent years demolished concrete waste handling and management is the new primary challenging issue faced by the countries all over the world. It is very challenging and hectic problem that has to be tackled in an indigenous manner, it is desirable to completely recycle demolished concrete waste in order to protect natural resources and reduce environmental pollution. In this research paper an experimental study is carried out to investigate the feasibility and recycling of demolished waste concrete for new construction. The present investigation to be focused on recycling demolished waste materials in order to reduce construction cost and resolving housing problems faced by the low income communities of the world. The crushed demolished concrete wastes is segregated by sieving to obtain required sizes of aggregate, several tests were conducted to determine the aggregate properties before recycling it into new concrete. This research shows that the recycled aggregate that are obtained from site make good quality concrete. The compressive strength test results of partial replacement and full recycled aggregate concrete and are found to be higher than the compressive strength of normal concrete with new aggregate.
Abstract: Academia-industry relationship is not like that of
technology donator-acceptor, but is of interactive and collaborative
nature, acknowledging and ensuring mutual respect for each other-s
role and contributions with an eye to attaining the true purpose of
such relationships, namely, bringing about research-outcome
synergy. Indeed, academia-industry interactions are a system that
requires active and collaborative participations of all the
stakeholders.
This paper examines various issues associated with academic
institutions and industry collaboration with special attention to the
nature of resources and potentialities of stakeholders in the context of
knowledge management. This paper also explores the barriers of
academia-industry interaction. It identifies potential areas where
industry-s participation with academia would be most effective for
synergism. Lastly, this paper proposes an integrated model of several
new collaborative approaches that are possible, mainly in the Indian
scenario to strengthen academia-industry interface.
Abstract: This study examined the effects of eight weeks of
whole-body vibration training (WBVT) on vertical and decuple jump
performance in handball athletes. Sixteen collegiate Level I handball
athletes volunteered for this study. They were divided equally as
control group and experimental group (EG). During the period of the
study, all athletes underwent the same handball specific training, but
the EG received additional WBVT (amplitude: 2 mm, frequency: 20 -
40 Hz) three time per week for eight consecutive weeks. The vertical
jump performance was evaluated according to the maximum height of
squat jump (SJ) and countermovement jump (CMJ). Single factor
ANCOVA was used to examine the differences in each parameter
between the groups after training with the pretest values as a covariate.
The statistic significance was set at p < .05. After 8 weeks WBVT, the
EG had significantly improved the maximal height of SJ (40.92 ± 2.96
cm vs. 48.40 ± 4.70 cm, F = 5.14, p < .05) and the maximal height
CMJ (47.25 ± 7.48 cm vs. 52.20 ± 6.25 cm, F = 5.31, p < .05). 8 weeks
of additional WBVT could improve the vertical and decuple jump
performance in handball athletes. Enhanced motor unit
synchronization and firing rates, facilitated muscular contraction
stretch-shortening cycle, and improved lower extremity
neuromuscular coordination could account for these enhancements.
Abstract: Tensile armour wires provide a flexible pipe's
resistance to longitudinal stresses. Flexible pipe manufacturers need
to know the effect of defects such as scratches and cracks, with
dimensions less than 0.2mm which is the limit of the current nondestructive
detection technology, on the fracture stress and fracture
strain of the wire for quality assurance purposes. Recent research
involving the determination of the fracture strength of cracked wires
employed laboratory testing and classical fracture mechanics
approach using non-standardised fracture mechanics specimens
because standard test specimens could not be manufactured from the
wires owing to their sizes. In this work, the effect of miniature
cracks on the fracture properties of tensile armour wires was
investigated using laboratory and finite element tensile testing
simulations with the phenomenological shear fracture model. The
investigation revealed that the presence of cracks shallower than
0.2mm is worse on the fracture strain of the wire.
Abstract: This paper reports the results of an experimental work
conducted to investigate the effect of curing conditions on the
compressive strength of self-compacting geopolymer concrete
prepared by using fly ash as base material and combination of sodium
hydroxide and sodium silicate as alkaline activator. The experiments
were conducted by varying the curing time and curing temperature in
the range of 24-96 hours and 60-90°C respectively. The essential
workability properties of freshly prepared Self-compacting
Geopolymer concrete such as filling ability, passing ability and
segregation resistance were evaluated by using Slump flow,
V-funnel, L-box and J-ring test methods. The fundamental
requirements of high flowability and resistance to segregation as
specified by guidelines on Self-compacting Concrete by EFNARC
were satisfied. Test results indicate that longer curing time and curing
the concrete specimens at higher temperatures result in higher
compressive strength. There was increase in compressive strength
with the increase in curing time; however increase in compressive
strength after 48 hours was not significant. Concrete specimens cured
at 70°C produced the highest compressive strength as compared to
specimens cured at 60°C, 80°C and 90°C.
Abstract: The wide increase and diffusion on telecommunication
technologies have caused a huge spread of electromagnetic sources
in most European Countries. Since the public is continuously being
exposed to electromagnetic radiation the possible health effects have
become the focus of population concerns. As a result, electromagnetic
field monitoring stations which control field strength in commercial
frequency bands are being placed on the flat roof of many buildings.
However there is no guidance on where to place them. This paper
presents an analysis of frequency, polarization and angles of incidence
of a plane wave which impinges on a flat roof security wall and its
dependence on electromagnetic field strength meters placement.