Abstract: The Adaptive Line Enhancer (ALE) is widely used for
enhancing narrowband signals corrupted by broadband noise. In this
paper, we propose novel ALE methods to improve the enhancing
capability. The proposed methods are motivated by the fact that the
output of the ALE is a fine estimate of the desired narrowband signal
with the broadband noise component suppressed. The proposed
methods preprocess the input signal using ALE filter to regenerate a
finer input signal. Thus the proposed ALE is driven by the input signal
with higher signal-to-noise ratio (SNR). The analysis and simulation
results are presented to demonstrate that the proposed ALE has better
performance than conventional ALE’s.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: In VLSI, testing plays an important role. Major
problem in testing are test data volume and test power. The important
solution to reduce test data volume and test time is test data
compression. The Proposed technique combines the bit maskdictionary
and 2n pattern run length-coding method and provides a
substantial improvement in the compression efficiency without
introducing any additional decompression penalty. This method has
been implemented using Mat lab and HDL Language to reduce test
data volume and memory requirements. This method is applied on
various benchmark test sets and compared the results with other
existing methods. The proposed technique can achieve a compression
ratio up to 86%.
Abstract: This paper presents the modeling approach in SBO
sequence for VVER 1000 reactors and describes the reactor core
behavior at late in-vessel phase in case of late reflooding by HPIS
and gives preliminary results for the ASTECv2 validation. The work
is focused on investigation of plant behavior during total loss of
power and the operator actions. The main goal of these analyses is to
assess the phenomena arising during the Station blackout (SBO)
followed by primary side high pressure injection system (HPIS)
reflooding of already damaged reactor core at very late “in-vessel”
phase. The purpose of the analyses is to define how the later HPIS
switching on can delay the time of vessel failure or possibly avoid
vessel failure. The times for HPP injection were chosen based on
previously performed investigations.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: Recently attention has been focused on incomplete
spinal cord injuries (SCI) to the central spine caused by pressure on
parts of the white matter conduction pathway, such as the pyramidal
tract. In this paper, we focus on a training robot designed to assist with
primary walking-pattern training. The target patient for this training
robot is relearning the basic functions of the usual walking pattern; it is
meant especially for those with incomplete-type SCI to the central
spine, who are capable of standing by themselves but not of
performing walking motions. From the perspective of human
engineering, we monitored the operator’s actions to the robot and
investigated the movement of joints of the lower extremities, the
circumference of the lower extremities, and exercise intensity with the
machine. The concept of the device was to provide mild training
without any sudden changes in heart rate or blood pressure, which will
be particularly useful for the elderly and disabled. The mechanism of
the robot is modified to be simple and lightweight with the expectation
that it will be used at home.
Abstract: In some applications, such as image recognition or
compression, segmentation refers to the process of partitioning a
digital image into multiple segments. Image segmentation is typically
used to locate objects and boundaries (lines, curves, etc.) in images.
Image segmentation is to classify or cluster an image into several
parts (regions) according to the feature of image, for example, the
pixel value or the frequency response. More precisely, image
segmentation is the process of assigning a label to every pixel in an
image such that pixels with the same label share certain visual
characteristics. The result of image segmentation is a set of segments
that collectively cover the entire image, or a set of contours extracted
from the image. Several image segmentation algorithms were
proposed to segment an image before recognition or compression. Up
to now, many image segmentation algorithms exist and be
extensively applied in science and daily life. According to their
segmentation method, we can approximately categorize them into
region-based segmentation, data clustering, and edge-base
segmentation. In this paper, we give a study of several popular image
segmentation algorithms that are available.
Abstract: Although there has been a growing interest in the
hybrid free-space optical link and radio frequency FSO/RF
communication system, the current literature is limited to results
obtained in moderate or cold environment. In this paper, using a soft
switching approach, we investigate the effect of weather
inhomogeneities on the strength of turbulence hence the channel
refractive index under Qatar harsh environment and their influence
on the hybrid FSO/RF availability. In this approach, either FSO/RF
or simultaneous or none of them can be active. Based on soft
switching approach and a finite state Markov Chain (FSMC) process,
we model the channel fading for the two links and derive a
mathematical expression for the outage probability of the hybrid
system. Then, we evaluate the behavior of the hybrid FSO/RF under
hazy and harsh weather. Results show that the FSO/RF soft switching
renders the system outage probability less than that of each link
individually. A soft switching algorithm is being implemented on
FPGAs using Raptor code interfaced to the two terminals of a
1Gbps/100 Mbps FSO/RF hybrid system, the first being implemented
in the region. Experimental results are compared to the above
simulation results.
Abstract: The present study aimed to determine the
effectiveness of Metaphor therapy on depression among female
students. The sample included 60 female students with depression
symptoms selected by simple sampling and randomly divided into
two equal groups (experimental and control groups). Beck
Depression Inventory was used to measure the variables. This was an
experimental study with a pre-test/post-test design with control
group. Eight metaphor therapy sessions were held for the
experimental group. A post-test was administered to both groups.
Data were analyzed using multivariate analysis of covariance
(MANCOVA). Results showed that the Metaphor therapy decreased
depression in the experimental group compared to the control group.
Abstract: The application of cold Radio-Frequency (RF) plasma
in the conservation of cultural heritage became important in the last
decades due to the positive results obtained in decontamination
treatments. This paper presents an equipment especially designed for cold RF
plasma application on paper documents, developed within a research
project. The equipment consists in two modules: the first one is
designed for decontamination and cleaning treatments of any type of
paper supports, while the second one can be used for coating friable
papers with adequate polymers, for protection purposes. All these
operations are carried out in cold radio-frequency plasma, working in
gaseous nitrogen, at low pressure. In order to optimize the equipment parameters ancient paper
samples infested with microorganisms have been treated in nitrogen
plasma and the decontamination effects, as well as changes in surface
properties (color, pH) were assessed. The microbiological analysis
revealed complete decontamination at 6 minutes treatment duration;
only minor modifications of the surface pH were found and the
colorimetric analysis showed a slight yellowing of the support.
Abstract: This study examined the mental health and behavioral
problems in early adolescence with the instrument of Achenbach
System of Empirically Based Assessment (ASEBA). The purpose of
the study was stratified sampling method was used to collect data
from 1975 participants. Multiple regression models and hierarchical
regression models were applied to examine the relations between the
background variables and internalizing problems, and the ones
between students’ performance and internalizing problems. The
results indicated that several background variables as predictors could
significantly predict the anxious/depressed problem; reading and
social study scores could significantly predict the anxious/depressed
problem. However the class as a hierarchical macro factor did not
indicate the significant effect. In brief, the majority of these models
represented that the background variables, behaviors and academic
performance were significantly related to the anxious/depressed
problem.
Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: Laban Movement Analysis (LMA), developed in the
dance community over the past seventy years, is an effective method
for observing, describing, notating, and interpreting human
movement to enhance communication and expression in everyday
and professional life. Many applications that use motion capture data
might be significantly leveraged if the Laban qualities will be
recognized automatically. This paper presents an automated
recognition method of Laban qualities from motion capture skeletal
recordings and it is demonstrated on the output of Microsoft’s Kinect
V2 sensor.
Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: Investigating the dynamic responses of high rise
structures under the effect of siesmic ground motion is extremely
important for the proper analysis and design of multitoried structures.
Since the presence of infilled walls strongly influences the behaviour
of frame systems in multistoried buildings, there is an increased need
for developing guidelines for the analysis and design of infilled
frames under the effect of dynamic loads for safe and proper design
of buildings. In this manuscript, we evaluate the natural frequencies
and natural periods of single bay single storey frames considering the
effect of infill walls by using the Eigen value analysis and validating
with SAP 2000 (free vibration analysis). Various parameters obtained
from the diagonal strut model followed for the free vibration analysis
is then compared with the Finite Element model, where infill is
modeled as shell elements (four noded). We also evaluated the effect
of various parameters on the natural periods of vibration obtained by
free vibration analysis in SAP 2000 comparing them with those
obtained by the empirical expressions presented in I.S. 1893(Part I)-
2002.
Abstract: Multiple-input multiple-output (MIMO) radar has
received increasing attention in recent years. MIMO radar has many
advantages over conventional phased array radar such as target
detection,resolution enhancement, and interference suppression. In
this paper, the results are presented from a simulation study of MIMO
uniformly-spaced linear array (ULA) antennas. The performance is
investigated under varied parameters, including varied array size,
pseudo random (PN) sequence length, number of snapshots, and
signal to noise ratio (SNR). The results of MIMO are compared to a
traditional array antenna.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: This survey paper shows the recent state of model
comparison as it’s applies to Model Driven engineering. In Model
Driven Engineering to calculate the difference between the models is
a very important and challenging task. There are number of tasks
involved in model differencing that firstly starts with identifying and
matching the elements of the model. In this paper, we discuss how
model matching is accomplished, the strategies, techniques and the
types of the model. We also discuss the future direction. We found
out that many of the latest model comparison strategies are geared
near enabling Meta model and similarity based matching. Therefore
model versioning is the most dominant application of the model
comparison. Recently to work on comparison for versioning has
begun to deteriorate, giving way to different applications. Ultimately
there is wide change among the tools in the measure of client exertion
needed to perform model comparisons, as some require more push to
encourage more sweeping statement and expressive force.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.