Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The paper describes the workings for four models of
CONWIP systems used till date; the basic CONWIP system, the
hybrid CONWIP system, the multi-product CONWIP system, and the
parallel CONWIP system. The final novel model is introduced in this
paper in a general form. These models may be adopted for analysis
for both simulation studies and implementation on the shop floor. For
each model, input parameters of interest are highlighted and their
impacts on several system performance measures are addressed.
Abstract: The running logs of a process hold valuable
information about its executed activity behavior and generated activity
logic structure. Theses informative logs can be extracted, analyzed and
utilized to improve the efficiencies of the process's execution and
conduction. One of the techniques used to accomplish the process
improvement is called as process mining. To mine similar processes is
such an improvement mission in process mining. Rather than directly
mining similar processes using a single comparing coefficient or a
complicate fitness function, this paper presents a simplified heuristic
process mining algorithm with two similarity comparisons that are
able to relatively conform the activity logic sequences (traces) of
mining processes with those of a normalized (regularized) one. The
relative process conformance is to find which of the mining processes
match the required activity sequences and relationships, further for
necessary and sufficient applications of the mined processes to process
improvements. One similarity presented is defined by the relationships
in terms of the number of similar activity sequences existing in
different processes; another similarity expresses the degree of the
similar (identical) activity sequences among the conforming processes.
Since these two similarities are with respect to certain typical behavior
(activity sequences) occurred in an entire process, the common
problems, such as the inappropriateness of an absolute comparison and
the incapability of an intrinsic information elicitation, which are often
appeared in other process conforming techniques, can be solved by the
relative process comparison presented in this paper. To demonstrate
the potentiality of the proposed algorithm, a numerical example is
illustrated.
Abstract: This paper presents the experimental results of silicone rubber housing material for 24kV lightning arrester under artificial accelerated ageing test based on IEC 61109 specifications. Specimens having inclined and alternated shed made of HTV silicone rubber with ATH content and having leakage distance 625 mm were tested continuously 1000 hrs in artificial salt fog chamber. After 1000 hrs of salt fog ageing test, obviously surface erosion was observed on trunk between the upper large shed and the lower small shed near the energized end. Decreasing in hydrophobicity and increasing in hardness were measured on tested specimen comparing with new specimen. Chemical analysis by ATR-FTIR confirmed the observation results.
Abstract: Life is beautiful. But, it is decided by genes, environment and the individual and shattered by the natural and / or the invited problems. Most of the global rural helpless masses are struggling for their survival since; they are neglected in all aspects of life including health. Amidst a countless number of miserable diseases in man, diabetes is becoming a dreaded killer and ramifying the entire globe in a jet speed. Diabetes control continues as a Herculean task to the scientific community and the modern society in the 21st century also. T2DM is not pertaining to any age and it can develop even during the childhood. This multifactorial disease abruptly changes the activities of certain vital biomarkers in the present rural T2DM cases. A remarkable variation in the levels of biomarkers like AST, ALT, GGT, ALP, LDH, HbA1C, C- peptide, fasting sugar, post-prandial sugar, sodium, potassium, BUN, creatinine and insulin show the rampant nature of T2DM in this physically active rural agrarian community.
Abstract: This paper presents data annotation models at five levels of granularity (database, relation, column, tuple, and cell) of relational data to address the problem of unsuitability of most relational databases to express annotations. These models do not require any structural and schematic changes to the underlying database. These models are also flexible, extensible, customizable, database-neutral, and platform-independent. This paper also presents an SQL-like query language, named Annotation Query Language (AnQL), to query annotation documents. AnQL is simple to understand and exploits the already-existent wide knowledge and skill set of SQL.
Abstract: The voice signal in Voice over Internet protocol (VoIP) system is processed through the best effort policy based IP network, which leads to the network degradations including delay, packet loss jitter. The work in this paper presents the implementation of finite impulse response (FIR) filter for voice quality improvement in the VoIP system through distributed arithmetic (DA) algorithm. The VoIP simulations are conducted with AMR-NB 6.70 kbps and G.729a speech coders at different packet loss rates and the performance of the enhanced VoIP signal is evaluated using the perceptual evaluation of speech quality (PESQ) measurement for narrowband signal. The results show reduction in the computational complexity in the system and significant improvement in the quality of the VoIP voice signal.
Abstract: Mobile Ad Hoc network is an infrastructure less
network which operates with the coordination of each node. Each node
believes to help another node, by forwarding its data to/from another
node. Unlike a wired network, nodes in an ad hoc network are resource
(i.e. battery, bandwidth computational capability and so on)
constrained. Such dependability of one node to another and limited
resources of nodes can result in non cooperation by any node to
accumulate its resources. Such non cooperation is known as selfish
behavior.
This paper discusses the performance analysis of very well known
MANET single-path (i.e. AODV) and multi-path (i.e. AOMDV)
routing protocol, in the presence of selfish behaviors. Along with
existing selfish behaviors, a new variation is also studied. Extensive
simulations were carried out using ns-2 and the study concluded that
the multi-path protocol (i.e. AOMDV) with link disjoint configuration
outperforms the other two configurations.
Abstract: A thirty Rahmani weaned male lambs of average body weight (27.28±1.40 kg) were randomly allotted to three similar groups, ten lambs in each, to study the benefit of commercial feed additives Tonilisat (Saccharomyces cerevisiae) and Roemin W2 (Lactobacillus acidophilus, Lactobacillus thermophilus, Bifidobacterium and Lactose) as growth promoters on lambs performance, digestibility, rumen activity and some blood constituents. The experiment lasted about 107 days. Three experimental groups were allotted as control group: received the basal ration, T1 group: received the basal ration supplemented with Tonilisat as (0.5kg/ ton concentrate feed mixture) and T2 group: received the basal ration supplemented with Roemin W2 (1kg/ ton concentrate feed mixture). Our study revealed that addition of Tonilisat significantly increased digestion coefficient of crude protein than that of the control group, Furthermore, the supplementation of Tonilisat or Roemin W2 increased (p
Abstract: Aluminum alloy has an extensive range of industrial application due to its consistent mechanical properties and structural integrity. The heat treatment by precipitation technique affected the Magnesium, Silicon Manganese and copper crystals dissolved in the Aluminum alloy. The crystals dislocated to precipitate on the crystal’s boundaries of the Aluminum alloy when given a thermal energy increased its hardness. In this project various times and temperature were varied to find out the best combination of these variables to increase the precipitation of the metals on the Aluminum crystal’s boundaries which will lead to get the highest hardness. These specimens are then tested for their hardness and tensile strength. It is noticed that when the temperature increases, the precipitation increases and consequently the hardness increases. A threshold temperature value (264C0) of Aluminum alloy should not be reached due to the occurrence of recrystalization which causes the crystal to grow. This recrystalization process affected the ductility of the alloy and decrease hardness. In addition, and while increasing the temperature the alloy’s mechanical properties will decrease. The mechanical properties, namely tensile and hardness properties are investigated according to standard procedures. In this research, different temperature and time have been applied to increase hardening.The highest hardness at 100°c in 6 hours equals to 207.31 HBR, while at the same temperature and time the lowest elongation equals to 146.5.
Abstract: If an unsteady heat transfer or heat impulse happens in
part of the cryogenic pipeline system of large space environment
simulation equipment while running in vacuum environment, it will
lead to abnormal flow of the cryogenic fluid in the pipeline. When the
situation gets worse, the cryogenic fluid in the pipeline will have phase
change and a gas block which results in the malfunction of the
cryogenic pipeline system. Referring to the structural parameter of a
typical cryogenic pipeline system and the basic equation, an analytical
model and a calculation model for cryogenic pipeline system can be
built. The various factors which influence the thermal resistance of a
cryogenic pipeline system can be analyzed and calculated by using the
qualitative analysis relation deduced for thermal resistance of pipeline.
The research conclusion could provide theoretical support for the
design and operation of a cryogenic pipeline system
Abstract: Wireless capsule Endoscopy (WCE) has rapidly
shown its wide applications in medical domain last ten years
thanks to its noninvasiveness for patients and support for thorough
inspection through a patient-s entire digestive system including
small intestine. However, one of the main barriers to efficient
clinical inspection procedure is that it requires large amount of
effort for clinicians to inspect huge data collected during the
examination, i.e., over 55,000 frames in video. In this paper, we
propose a method to compute meaningful motion changes of
WCE by analyzing the obtained video frames based on regional
optical flow estimations. The computed motion vectors are used to
remove duplicate video frames caused by WCE-s imaging nature,
such as repetitive forward-backward motions from peristaltic
movements. The motion vectors are derived by calculating
directional component vectors in four local regions. Our
experiments are performed on small intestine area, which is of
main interest to clinical experts when using WCEs, and our
experimental results show significant frame reductions comparing
with a simple frame-to-frame similarity-based image reduction
method.
Abstract: This study describes the preparation of a novel proton
conducting membranes based on bacterial cellulose (BC) modified by
grafting of 2-acrylamido-2-methyl-1 -propanesulfonic acid (AMPS)
through UV-induced graft polymerization. These AMPS-g-BC
membranes have been characterized by various techniques including
FTIR, SEM and TGA, to find their successful grafting of AMPS on
BC, surface morphology and thermal stability, respectively. Physical
properties of AMPS-g-BC membranes have been assessed in terms of
Lamda value( λ ), ion exchange capacity(IEC) and proton
conductivity. The relationship between degree of grafting and AMPS
concentration used for grafting has been determined by weight gain
method. An optimum proton conductivity equal to 2.89x10-2 S cm-1
and IEC value equal to 1.79 mmol g-1 have been obtained when 20
wt% AMPS concentration is used for grafting (i.e. the corresponding
membrane is notated as AMPS20-g-BC).
Abstract: Due to insufficient frequency band and tremendous growth of the mobile users, complex computation is needed for the use of resources. Long distance communication began with the introduction of telegraphs and simple coded pulses, which were used to transmit short messages. Since then numerous advances have rendered reliable transfer of information both easier and quicker. Wireless network refers to any type of computer network that is wireless, and is commonly associated with a telecommunications network whose interconnections between nodes is implemented without the use of wires. Wireless network can be broadly categorized in infrastructure network and infrastructure less network. Infrastructure network is one in which we have a base station to serve the mobile users and in the infrastructure less network is one in which no infrastructure is available to serve the mobile users this kind of networks are also known as mobile Adhoc networks. In this paper we have simulated the result for different scenarios with protocols like AODV and DSR; we simulated the result for throughput, delay and receiving traffic in the given scenario.
Abstract: Two different superhydrophobic surfaces were
elaborated and their oil repellency behavior was evaluated using
several liquid with different surface tension. A silicone rubber/SiO2
nanocomposite coated (A) on aluminum substrate by “spin-coating"
and the sample B was an anodized aluminum surface covered by
Teflon-like coating. A high static contact angle about ∼162° was
measured for two prepared surfaces on which the water droplet rolloff.
Scanning electron microscopy (SEM) showed the presence of
micro/nanostructures for both sample A and B similar to that of lotus
leaf.
However the sample A presented significantly different behaviour
of wettability against the low surface tension liquid. Sample A has
been wetted totally by oil (dodecan) droplet while sample B showed
oleophobic behaviour. Oleophobic property of Teflon like coating
can be contributed to the presence of CF2 and CF3 functional group
which was shown by XPS analysis.
Abstract: This paper is concerned with the existence of a linear copositive Lyapunov function(LCLF) for a special class of switched positive linear systems(SPLSs) composed of continuousand discrete-time subsystems. Firstly, by using system matrices, we construct a special kind of matrices in appropriate manner. Secondly, our results reveal that the Hurwitz stability of these matrices is equivalent to the existence of a common LCLF for arbitrary finite sets composed of continuous- and discrete-time positive linear timeinvariant( LTI) systems. Finally, a simple example is provided to illustrate the implication of our results.
Abstract: Organization of video databases is becoming difficult
task as the amount of video content increases. Video classification
based on the content of videos can significantly increase the speed of
tasks such as browsing and searching for a particular video in a
database. In this paper, a content-based videos classification system
for the classes indoor and outdoor is presented. The system is
intended to be used on a mobile platform with modest resources. The
algorithm makes use of the temporal redundancy in videos, which
allows using an uncomplicated classification model while still
achieving reasonable accuracy. The training and evaluation was done
on a video database of 443 videos downloaded from a video sharing
service. A total accuracy of 87.36% was achieved.
Abstract: This paper tries to study the effect of geosynthetic inclusion on the improvement of the load-settlement characters of two layered soil. In addition, the effect of geogrid and geotextile in reduction of the required thickness of subbase layer in unpaved roads is studied. Considering the vast application of bearing ratio tests in road construction projects, this test is used in present investigation. Bearing ratio tests were performed on two layered soil including a granular soil layer at the top (as the subbase layer) and a weak clayey soil placed at the bottom (as the subgrade layer). These tests were performed for different conditions including unreinforced and reinforced by geogrid and geotextile and three thicknesses for top layer soil (subbase layer). In the reinforced condition the reinforcing element was placed on the interface of the top granular layer and the beneath clayey layer to study the separation effect of geosynthetics. In all tests the soils (both granular and clayey soil layers) were compacted according to optimum water content. At the end, the diagrams were plotted and were compared with each other. Furthermore, a comparison between geogrids and geotextiles behaviors on two layer soil is done in this paper. The results show an increase in compression strength of reinforced specimen in comparison with unreinforced soil sample. The effect of geosynthetic inclusion reduces by increasing the subbase thickness. In addition it was found that geogrids have more desirable behavior rather than geotextiles due to interlocking with the subbase layer aggregates.
Abstract: M. Kemal Ataturk was a great leader who was fond of art and he had displayed his being fond of art many times. In his speeches and writings you can see that he had showed his approval to art and the importance of artists and art for the society. During the foundation of republic, he also wanted renovation in art as in other fields and ordered many novelties both in art and society. One of the greatest steps in realizing this was to prepare a national Turkish opera. In this study, it was studied how a Turkish opera, Özsoy was prepared in the context of social and political conditions of that time and what kind of processes it passed. As a result, it is seen that there was two main aims for Ataturk with this opera. First, Ataturk wanted to abolish the sectarian conflict between Iran and Turkey going on for centuries. The second and maybe the most important is that he wanted to make a revolution in the field of art and aimed to reach the level of civilized countries.