Abstract: Theobjective of this study was to evaluate the optimal
treatment condition of Fenton oxidation process to removal
contaminant in soil slurry contaminated by petroleum hydrocarbons.
This research studied somefactors that affect the removal efficiency
of petroleum hydrocarbons in soil slurry including molar ratio of
hydrogen peroxide (H2O2) to ferrous ion(Fe2+), pH condition and
reaction time.The resultsdemonstrated that the optimum condition
was that the molar ratio of H2O2:Fe3+ was 200:1,the pHwas 4.0and
the rate of reaction was increasing rapidly from starting point to 7th
hour and destruction kinetic rate (k) was 0.24 h-1. Approximately
96% of petroleum hydrocarbon was observed(initialtotal petroleum
hydrocarbon (TPH) concentration = 70±7gkg-1)
Abstract: Block replacement algorithms to increase hit ratio
have been extensively used in cache memory management. Among
basic replacement schemes, LRU and FIFO have been shown to be
effective replacement algorithms in terms of hit rates. In this paper,
we introduce a flexible stack-based circuit which can be employed in
hardware implementation of both LRU and FIFO policies. We
propose a simple and efficient architecture such that stack-based
replacement algorithms can be implemented without the drawbacks
of the traditional architectures. The stack is modular and hence, a set
of stack rows can be cascaded depending on the number of blocks in
each cache set. Our circuit can be implemented in conjunction with
the cache controller and static/dynamic memories to form a cache
system. Experimental results exhibit that our proposed circuit
provides an average value of 26% improvement in storage bits and its
maximum operating frequency is increased by a factor of two
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.
Abstract: An epidemiological cross sectional study was
undertaken in Yaoundé in 2002 and updated in 2005. Focused on
health within the city, the objectives were to measure diarrheal
prevalence and to identify the risk factors associated with them.
Results of microbiological examinations have revealed an urban
average prevalence rate of 14.5%. Access to basic services in the
living environment appears to be an important risk factor for
diarrheas. Statistical and spatial analyses conducted have revealed
that prevalence of diarrheal diseases vary among the two main types
of settlement (informal and planned). More importantly, this study
shows that, diarrhea prevalence rates (notably bacterial and parasitic
diarrheas) vary according to the sub- category of settlements. The
study draws a number of theoretical and policy implications for
researchers and policy decision makers.
Abstract: The paper presents the influence of the conventional
ploughing tillage technology in comparison with the minimum
tillage, upon the soil properties, weed control and yield in the case of
maize (Zea mays L.), soya-bean (Glycine hispida L.) and winter
wheat (Triticum aestivum L.) in a three years crop rotation. A
research has been conducted at the University of Agricultural
Sciences and Veterinary Medicine Cluj-Napoca, Romania. The use of
minimum soil tillage systems within a three years rotation: maize,
soya-bean, wheat favorites the rise of the aggregates hydro stability
with 5.6-7.5% on a 0-20 cm depth and 5-11% on 20-30 cm depth.
The minimum soil tillage systems – paraplow, chisel or rotary grape
– are polyvalent alternatives for basic preparation, germination bed
preparation and sowing, for fields and crops with moderate loose
requirements being optimized technologies for: soil natural fertility
activation and rationalization, reduction of erosion, increasing the
accumulation capacity for water and realization of sowing in the
optimal period. The soil tillage system influences the productivity
elements of cultivated species and finally the productions thus
obtained. Thus, related to conventional working system, the
productions registered in minimum tillage working represented 89-
97% in maize, 103-112% in soya-bean, 93-99% in winter-wheat. The
results of investigations showed that the yield is a conclusion soil
tillage systems influence on soil properties, plant density assurance
and on weed control. Under minimum tillage systems in the case of
winter weat as an option for replacing classic ploughing, the best
results in terms of quality indices were obtained from version worked
with paraplow, followed by rotary harrow and chisel. At variants
worked with paraplow were obtained quality indices close to those of
the variant worked with plow, and protein and gluten content was
even higher. At Ariesan variety, highest protein content, 12.50% and
gluten, 28.6% was obtained for the variant paraplow.
Abstract: This article is an extension and a practical application
approach of Wheeler-s NEBIC theory (Net Enabled Business
Innovation Cycle). NEBIC theory is a new approach in IS research
and can be used for dynamic environment related to new technology.
Firms can follow the market changes rapidly with support of the IT
resources. Flexible firms adapt their market strategies, and respond
more quickly to customers changing behaviors. When every leading
firm in an industry has access to the same IT resources, the way that
these IT resources are managed will determine the competitive
advantages or disadvantages of firm. From Dynamic Capabilities
Perspective and from newly introduced NEBIC theory by Wheeler,
we know that only IT resources cannot deliver customer value but
good configuration of those resources can guarantee customer value
by choosing the right emerging technology, grasping the economic
opportunities through business innovation and growth. We found
evidences in literature that SOA (Service Oriented Architecture) is a
promising emerging technology which can deliver the desired
economic opportunity through modularity, flexibility and loosecoupling.
SOA can also help firms to connect in network which can
open a new window of opportunity to collaborate in innovation and
right kind of outsourcing
Abstract: This paper will focus on modeling, analysis and simulation of a 42V/14V dc/dc converter based architecture. This architecture is considered to be technically a viable solution for automotive dual-voltage power system for passenger car in the near further. An interleaved dc/dc converter system is chosen for the automotive converter topology due to its advantages regarding filter reduction, dynamic response, and power management. Presented herein, is a model based on one kilowatt interleaved six-phase buck converter designed to operate in a Discontinuous Conduction Mode (DCM). The control strategy of the converter is based on a voltagemode- controlled Pulse Width Modulation (PWM) with a Proportional-Integral-Derivative (PID). The effectiveness of the interleaved step-down converter is verified through simulation results using control-oriented simulator, MatLab/Simulink.
Abstract: The White Kwao (Pueraria mirifica), a potent phytoestrogenic medicinal plant, has long been use in Thailand as a traditional folkmedicine. However, no scientific information of the direct effect of White Kwao on the development of mammalian embryo was available. Therefore, the purpose of this study was to investigate the effect of White Kwao extract on the in vitro development and implantation rate of mouse embryos. This study was designed into two experiments. In the first experiment, the two-cell stage mouse embryos were collected from the oviduct of superovulated mature female mice, and randomly cultured in three different media, the M16, M16 supplemented with 0.52μg esthinylestradiol-17β, and M16 supplemented with 10 mg/ml White Kwao extract. The culture was incubated in CO2 incubator at 37 oC . After the embryos were cultivated, the developments of embryos were observed every 24 hours for 5 days. The development rate of embryos from the two-cell stage to blastocyst stage in the media was with White Kwao was significantly higher (p
Abstract: Various assisted reproductive techniques have been
developed and refined to obtain a large number of offspring from
genetically superior animals or obtain offspring from infertile (or
subfertile) animals. The embryo transfer is one assisted reproductive
technique developed well, aimed at increased productivity of selected
females, disease control, importation and exportation of livestock,
rapid screening of AI sires for genetically recessive characteristics,
treatment or circumvention of certain types of infertility. Embryo
transfer also is a useful research tool for evaluating fetal and maternal
interactions. This technique has been applied to nearly every species
of domestic animal and many species of wildlife and exotic animals,
including humans and non-human primates. The successful of
embryo transfers have been limited to within-animal, homologous
replacement of the embryos. There are several examples of
interspecific and intergeneric embryo transfers in which embryos
implanted but did not develop to term: sheep and goat, mouse and rat.
An immunological rejections and placental incompatibility between
the embryo and the surrogate mother appear to restrict interspecific
embryo transfer/interspecific pregnancy. Recently, preimplantation
embryo manipulation procedures have been applied, such as
technique of inner cell mass transfer. This technique will possible to
overcome the reproductive barrier interspecific embryo
transfer/interspecific pregnancy, if there is a protective mechanism
which prevents recognition of the foreign fetus by the mother of the
other species
Abstract: A new power regulator controller with multiple-access
PID compensator is proposed, which can achieve a minimum memory
requirement for fully table look-up. The proposed regulator controller
employs hysteresis comparators, an error process unit (EPU) for
voltage regulation, a multiple-access PID compensator and a lowpower-
consumption digital PWM (DPWM). Based on the multipleaccess
mechanism, the proposed controller can alleviate the penalty of
large amount of memory employed for fully table look-up based PID
compensator in the applications of power regulation. The proposed
controller has been validated with simulation results.
Abstract: Chemical reaction and diffusion are important phenomena in quantitative neurobiology and biophysics. The knowledge of the dynamics of calcium Ca2+ is very important in cellular physiology because Ca2+ binds to many proteins and regulates their activity and interactions Calcium waves propagate inside cells due to a regenerative mechanism known as calcium-induced calcium release. Buffer-mediated calcium diffusion in the cytosol plays a crucial role in the process. A mathematical model has been developed for calcium waves by assuming the buffers are in equilibrium with calcium i.e., the rapid buffering approximation for a one dimensional unsteady state case. This model incorporates important physical and physiological parameters like dissociation rate, diffusion rate, total buffer concentration and influx. The finite difference method has been employed to predict [Ca2+] and buffer concentration time course regardless of the calcium influx. The comparative studies of the effect of the rapid buffered diffusion and kinetic parameters of the model on the concentration time course have been performed.
Abstract: Square pipes (pipes with square cross sections) are
being used for various industrial objectives, such as machine
structure components and housing/building elements. The utilization
of them is extending rapidly and widely. Hence, the out-put of those
pipes is increasing and new application fields are continually
developing.
Due to various demands in recent time, the products have to
satisfy difficult specifications with high accuracy in dimensions. The
reshaping process design of pipes with square cross sections;
however, is performed by trial and error and based on expert-s
experience.
In this paper, a computer-aided simulation is developed based on
the 2-D elastic-plastic method with consideration of the shear
deformation to analyze the reshaping process. Effect of various
parameters such as diameter of the circular pipe and mechanical
properties of metal on product dimension and quality can be
evaluated by using this simulation. Moreover, design of reshaping
process include determination of shrinkage of cross section,
necessary number of stands, radius of rolls and height of pipe at each
stand, are investigated. Further, it is shown that there are good
agreements between the results of the design method and the
experimental results.
Abstract: In this paper, transversal vibration of buried pipelines
during loading induced by underground explosions is analyzed. The
pipeline is modeled as an infinite beam on an elastic foundation, so
that soil-structure interaction is considered by means of transverse
linear springs along the pipeline. The pipeline behavior is assumed to
be ideal elasto-plastic which an ultimate strain value limits the plastic
behavior. The blast loading is considered as a point load, considering
the affected length at some point of the pipeline, in which the
magnitude decreases exponentially with time. A closed-form solution
for the quasi-static problem is carried out for both elastic and elasticperfect
plastic behaviors of pipe materials. At the end, a comparative
study on steel and polyethylene pipes with different sizes buried in
various soil conditions, affected by a predefined underground
explosion is conducted, in which effect of each parameter is
discussed.
Abstract: Phishing scheme is a new emerged security issue of
E-Commerce Crime in globalization. In this paper, the legal scaffold
of Malaysia, United States and United Kingdom are analyzed and
followed by discussion on critical issues that rose due to phishing
activities. The result revealed that inadequacy of current legal
framework is the main challenge to govern this epidemic. However,
lack of awareness among consumers, crisis on merchant-s
responsibility and lack of intrusion reports and incentive arrangement
contributes to phishing proliferating. Prevention is always better than
curb. By the end of this paper, some best practices for consumers and
corporations are suggested.
Abstract: Rapid economic development and population growth
in Malaysia had accelerated the generation of solid waste. This issue
gives pressure for effective management of municipal solid waste
(MSW) to take place in Malaysia due to the increased cost of landfill.
This paper discusses optimal planning of waste-to-energy (WTE)
using a combinatorial simulation and optimization model through
mixed integer linear programming (MILP) approach. The proposed
multi-period model is tested in Iskandar Malaysia (IM) as case study
for a period of 12 years (2011 -2025) to illustrate the economic
potential and tradeoffs involved in this study. In this paper, 3
scenarios have been used to demonstrate the applicability of the
model: (1) Incineration scenario (2) Landfill scenario (3) Optimal
scenario. The model revealed that the minimum cost of electricity
generation from 9,995,855 tonnes of MSW is estimated as USD
387million with a total electricity generation of 50MW /yr in the
optimal scenario.
Abstract: Nowadays, with the emerging of the new applications
like robot control in image processing, artificial vision for visual
servoing is a rapidly growing discipline and Human-machine
interaction plays a significant role for controlling the robot. This
paper presents a new algorithm based on spatio-temporal volumes for
visual servoing aims to control robots. In this algorithm, after
applying necessary pre-processing on video frames, a spatio-temporal
volume is constructed for each gesture and feature vector is extracted.
These volumes are then analyzed for matching in two consecutive
stages. For hand gesture recognition and classification we tested
different classifiers including k-Nearest neighbor, learning vector
quantization and back propagation neural networks. We tested the
proposed algorithm with the collected data set and results showed the
correct gesture recognition rate of 99.58 percent. We also tested the
algorithm with noisy images and algorithm showed the correct
recognition rate of 97.92 percent in noisy images.
Abstract: Effective evaluation of software development effort is an important aspect of successful project management. Based on a large database with 4106 projects ever developed, this study statistically examines the factors that influence development effort. The factors found to be significant for effort are project size, average number of developers that worked on the project, type of development, development language, development platform, and the use of rapid application development. Among these factors, project size is the most critical cost driver. Unsurprisingly, this study found that the use of CASE tools does not necessarily reduce development effort, which adds support to the claim that the use of tools is subtle. As many of the current estimation models are rarely or unsuccessfully used, this study proposes a parsimonious parametric model for the prediction of effort which is both simple and more accurate than previous models.
Abstract: Prior to the use of detectors, characteristics
comparison study was performed and baseline established. In patient
specific QA, the portal dosimetry mean values of area gamma,
average gamma and maximum gamma were 1.02, 0.31 and 1.31 with
standard deviation of 0.33, 0.03 and 0.14 for IMRT and the
corresponding values were 1.58, 0.48 and 1.73 with standard
deviation of 0.31, 0.06 and 0.66 for VMAT. With ImatriXX 2-D
array system, on an average 99.35% of the pixels passed the criteria
of 3%-3 mm gamma with standard deviation of 0.24 for dynamic
IMRT. For VMAT, the average value was 98.16% with a standard
deviation of 0.86. The results showed that both the systems can be
used in patient specific QA measurements for IMRT and VMAT.
The values obtained with the portal dosimetry system were found to
be relatively more consistent compared to those obtained with
ImatriXX 2-D array system.
Abstract: Every 2-3 years the influenza B virus serves
epidemics. Neuraminidase (NA) is an important target for influenza
drug design. Although, oseltamivir, an oral neuraminidase drug, has
been shown good inhibitory efficiency against wild-type of influenza
B virus, the lower susceptibility to the R152K mutation has been
reported. Better understanding of oseltamivir efficiency and
resistance toward the influenza B NA wild-type and R152K mutant,
respectively, could be useful for rational drug design. Here, two
complex systems of wild-type and R152K NAs with oseltamivir
bound were studied using molecular dynamics (MD) simulations.
Based on 5-ns MD simulation, the loss of notable hydrogen bond and
decrease in per-residue decomposition energy from the mutated
residue K152 contributed to drug compared to those of R152 in wildtype
were found to be a primary source of high-level of oseltamivir
resistance due to the R152K mutation.
Abstract: The paper presents the virtual model of the active
suspension system used for improving the dynamic behavior of a
motor vehicle. The study is focused on the design of the control
system, the purpose being to minimize the effect of the road
disturbances (which are considered as perturbations for the control
system). The analysis is performed for a quarter-car model, which
corresponds to the suspension system of the front wheel, by using the
DFC (Design for Control) software solution EASY5 (Engineering
Analysis Systems) of MSC Software. The controller, which is a PIDbased
device, is designed through a parametric optimization with the
Matrix Algebra Tool (MAT), considering the gain factors as design
variables, while the design objective is to minimize the overshoot of
the indicial response.