Abstract: The study in this paper underlines the importance of
correct joint selection of the spreading codes for uplink of multicarrier
code division multiple access (MC-CDMA) at the transmitter
side and detector at the receiver side in the presence of nonlinear
distortion due to high power amplifier (HPA). The bit error rate
(BER) of system for different spreading sequences (Walsh code, Gold
code, orthogonal Gold code, Golay code and Zadoff-Chu code) and
different kinds of receivers (minimum mean-square error receiver
(MMSE-MUD) and microstatistic multi-user receiver (MSF-MUD))
is compared by means of simulations for MC-CDMA transmission
system. Finally, the results of analysis will show, that the application
of MSF-MUD in combination with Golay codes can outperform
significantly the other tested spreading codes and receivers for all
mostly used models of HPA.
Abstract: This article presents the simulation, parameterization and optimization of an electromagnet with the C–shaped configuration, intended for the study of magnetic properties of materials. The electromagnet studied consists of a C-shaped yoke, which provides self–shielding for minimizing losses of magnetic flux density, two poles of high magnetic permeability and power coils wound on the poles. The main physical variable studied was the static magnetic flux density in a column within the gap between the poles, with 4cm2 of square cross section and a length of 5cm, seeking a suitable set of parameters that allow us to achieve a uniform magnetic flux density of 1x104 Gaussor values above this in the column, when the system operates at room temperature and with a current consumption not exceeding 5A. By means of a magnetostatic analysis by the finite element method, the magnetic flux density and the distribution of the magnetic field lines were visualized and quantified. From the results obtained by simulating an initial configuration of electromagnet, a structural optimization of the geometry of the adjustable caps for the ends of the poles was performed. The magnetic permeability effect of the soft magnetic materials used in the poles system, such as low– carbon steel (0.08% C), Permalloy (45% Ni, 54.7% Fe) and Mumetal (21.2% Fe, 78.5% Ni), was also evaluated. The intensity and uniformity of the magnetic field in the gap showed a high dependence with the factors described above. The magnetic field achieved in the column was uniform and its magnitude ranged between 1.5x104 Gauss and 1.9x104 Gauss according to the material of the pole used, with the possibility of increasing the magnetic field by choosing a suitable geometry of the cap, introducing a cooling system for the coils and adjusting the spacing between the poles. This makes the device a versatile and scalable tool to generate the magnetic field necessary to perform magnetic characterization of materials by techniques such as vibrating sample magnetometry (VSM), Hall-effect, Kerr-effect magnetometry, among others. Additionally, a CAD design of the modules of the electromagnet is presented in order to facilitate the construction and scaling of the physical device.
Abstract: This paper presents comparative study on recent
integer DCTs and a new method to construct a low sensitive structure
of integer DCT for colored input signals. The method refers to
sensitivity of multiplier coefficients to finite word length as an
indicator of how word length truncation effects on quality of output
signal. The sensitivity is also theoretically evaluated as a function of
auto-correlation and covariance matrix of input signal. The structure of
integer DCT algorithm is optimized by combination of lower sensitive
lifting structure types of IRT. It is evaluated by the sensitivity of
multiplier coefficients to finite word length expression in a function of
covariance matrix of input signal. Effectiveness of the optimum
combination of IRT in integer DCT algorithm is confirmed by quality
improvement comparing with existing case. As a result, the optimum
combination of IRT in each integer DCT algorithm evidently improves
output signal quality and it is still compatible with the existing one.
Abstract: Border Gateway Protocol (BGP) is the standard routing protocol between various autonomous systems (AS) in the internet. In the event of failure, a considerable delay in the BGP convergence has been shown by empirical measurements. During the convergence time the BGP will repeatedly advertise new routes to some destination and withdraw old ones until it reach a stable state. It has been found that the KEEPALIVE message timer and the HOLD time are tow parameters affecting the convergence speed. This paper aims to find the optimum value for the KEEPALIVE timer and the HOLD time that maximally reduces the convergence time without increasing the traffic. The KEEPALIVE message timer optimal value founded by this paper is 30 second instead of 60 seconds, and the optimal value for the HOLD time is 90 seconds instead of 180 seconds.
Abstract: This study compares three meta heuristics to minimize makespan (Cmax) for Hybrid Flow Shop (HFS) Scheduling Problem with Parallel Machines. This problem is known to be NP-Hard. This study proposes three algorithms among improvement heuristic searches which are: Genetic Algorithm (GA), Simulated Annealing (SA), and Tabu Search (TS). SA and TS are known as deterministic improvement heuristic search. GA is known as stochastic improvement heuristic search. A comprehensive comparison from these three improvement heuristic searches is presented. The results for the experiments conducted show that TS is effective and efficient to solve HFS scheduling problems.
Abstract: This paper presents modeling and optimization of two NP-hard problems in flexible manufacturing system (FMS), part type selection problem and loading problem. Due to the complexity and extent of the problems, the paper was split into two parts. The first part of the papers has discussed the modeling of the problems and showed how the real coded genetic algorithms (RCGA) can be applied to solve the problems. This second part discusses the effectiveness of the RCGA which uses an array of real numbers as chromosome representation. The novel proposed chromosome representation produces only feasible solutions which minimize a computational time needed by GA to push its population toward feasible search space or repair infeasible chromosomes. The proposed RCGA improves the FMS performance by considering two objectives, maximizing system throughput and maintaining the balance of the system (minimizing system unbalance). The resulted objective values are compared to the optimum values produced by branch-and-bound method. The experiments show that the proposed RCGA could reach near optimum solutions in a reasonable amount of time.
Abstract: Interpretation of aerial images is an important task in
various applications. Image segmentation can be viewed as the essential
step for extracting information from aerial images. Among many
developed segmentation methods, the technique of clustering has been
extensively investigated and used. However, determining the number
of clusters in an image is inherently a difficult problem, especially
when a priori information on the aerial image is unavailable. This
study proposes a support vector machine approach for clustering
aerial images. Three cluster validity indices, distance-based index,
Davies-Bouldin index, and Xie-Beni index, are utilized as quantitative
measures of the quality of clustering results. Comparisons on the
effectiveness of these indices and various parameters settings on the
proposed methods are conducted. Experimental results are provided
to illustrate the feasibility of the proposed approach.
Abstract: The number of features required to represent an image
can be very huge. Using all available features to recognize objects
can suffer from curse dimensionality. Feature selection and
extraction is the pre-processing step of image mining. Main issues in
analyzing images is the effective identification of features and
another one is extracting them. The mining problem that has been
focused is the grouping of features for different shapes. Experiments
have been conducted by using shape outline as the features. Shape
outline readings are put through normalization and dimensionality
reduction process using an eigenvector based method to produce a
new set of readings. After this pre-processing step data will be
grouped through their shapes. Through statistical analysis, these
readings together with peak measures a robust classification and
recognition process is achieved. Tests showed that the suggested
methods are able to automatically recognize objects through their
shapes. Finally, experiments also demonstrate the system invariance
to rotation, translation, scale, reflection and to a small degree of
distortion.
Abstract: In order to make surfing the internet faster, and to save redundant processing load with each request for the same web page, many caching techniques have been developed to reduce latency of retrieving data on World Wide Web. In this paper we will give a quick overview of existing web caching techniques used for dynamic web pages then we will introduce a design and implementation model that take advantage of “URL Rewriting" feature in some popular web servers, e.g. Apache, to provide an effective approach of caching dynamic web pages.
Abstract: Active Vibration Control (AVC) is an important
problem in structures. One of the ways to tackle this problem is to
make the structure smart, adaptive and self-controlling. The objective
of active vibration control is to reduce the vibration of a system by
automatic modification of the system-s structural response. This
paper features the modeling and design of a Periodic Output
Feedback (POF) control technique for the active vibration control of
a flexible Timoshenko cantilever beam for a multivariable case with
2 inputs and 2 outputs by retaining the first 2 dominant vibratory
modes using the smart structure concept. The entire structure is
modeled in state space form using the concept of piezoelectric
theory, Timoshenko beam theory, Finite Element Method (FEM) and
the state space techniques. Simulations are performed in MATLAB.
The effect of placing the sensor / actuator at 2 finite element
locations along the length of the beam is observed. The open loop
responses, closed loop responses and the tip displacements with and
without the controller are obtained and the performance of the smart
system is evaluated for active vibration control.
Abstract: The purpose of this study is to examine the self and
decision making levels of students receiving education in schools of
physical training and sports. The population of the study consisted
258 students, among which 152 were male and 106 were female
( X age=19,3713 + 1,6968), that received education in the schools of
physical education and sports of Selcuk University, Inonu University,
Gazi University and Karamanoglu Mehmetbey University. In order to
achieve the purpose of the study, the Melbourne Decision Making
Questionnary developed by Mann et al. (1998) [1] and adapted to
Turkish by Deniz (2004) [2] and the Self-Esteem Scale developed by
Aricak (1999) [3] was utilized. For analyzing and interpreting data
Kolmogorov-Smirnov test, t-test and one way anova test were used,
while for determining the difference between the groups Tukey test
and Multiple Linear Regression test were employed and significance
was accepted at P
Abstract: Smart Dust particles, are small smart materials used for generating weather maps. We investigate question of the optimal number of Smart Dust particles necessary for generating precise, computationally feasible and cost effective 3–D weather maps. We also give an optimal matching algorithm for the generalized scenario, when there are N Smart Dust particles and M ground receivers.
Abstract: In this paper, an analytical modeling is presentated to
describe the channel noise in GME SGT/CGT MOSFET, based on
explicit functions of MOSFETs geometry and biasing conditions for
all channel length down to deep submicron and is verified with the
experimental data. Results shows the impact of various parameters
such as gate bias, drain bias, channel length ,device diameter and gate
material work function difference on drain current noise spectral
density of the device reflecting its applicability for circuit design
applications.
Abstract: Computerized alarm systems have been applied
increasingly to nuclear power plants. For existing plants, an add-on
computer alarm system is often installed to the control rooms. Alarm
avalanches during the plant transients are major problems with the
alarm systems in nuclear power plants. Computerized alarm systems
can process alarms to reduce the number of alarms during the plant
transients. This paper describes various alarm processing methods, an
alarm cause tracking function, and various alarm presentation schemes
to show alarm information to the operators effectively which are
considered during the development of several computerized alarm
systems for Korean nuclear power plants and are found to be helpful to
the operators.
Abstract: In many buildings we rely on large footings to offer
structural stability. Designers often compensate for the lack of
knowledge available with regard to foundation-soil interaction by
furnishing structures with overly large footings. This may lead to a
significant increase in building expenditures if many large
foundations are present. This paper describes the interface material
law that governs the behavior along the contact surface of adjacent
materials, and the behavior of a large foundation under ultimate limit
loading. A case study is chosen that represents a common
foundation-soil system frequently used in general practice and
therefore relevant to other structures. Investigations include
compressing versus uplifting wind forces, alterations to the
foundation size and subgrade compositions, the role of the slab
stiffness and presence and the effect of commonly used structural
joints and connections. These investigations aim to provide the
reader with an objective design approach, efficiently preventing
structural instability.
Abstract: Biological Ammonia removal (nitrification), the
oxidation of ammonia to nitrate catalyzed by bacteria, is a key part of
global nitrogen cycling. In the first step of nitrification,
chemolithoautotrophic ammonia oxidizer transform ammonia to
nitrite, this subsequently oxidized to nitrate by nitrite oxidizing
bacteria. This process can be affected by several factors. In this study
the effect of influent COD on biological ammonia removal in a
bench-scale biological reactor was investigated. Experiments were
carried out using synthetic wastewater. The initial ammonium
concentration was 25mgNH4
+-N L-1. The effect of COD between
247.55±1.8 and 601.08±3.24mgL-1 on biological ammonia removal
was investigated by varying the COD loading supplied to reactor.
From the results obtained in this study it could be concluded in the
range of 247.55±1.8 to 351.35±2.05mgL-1, there is a direct
relationship between amount of COD and ammonia removal.
However more than 351.35±2.05 up to 601.08±3.24mgL-1 were
found an indirect relationship between them.
Abstract: The purpose of this study was to evaluate the tissue
composition and carcass muscularity of 32 legs of Ile de France
lambs fed with diets containing sunflower seeds and vitamin E, with
mean body weight of 15 kg, lodged in individual pens at 15 kg and
slaughtered at 32 kg of body weight. The treatments influenced
(P0,05) by the treatments. The
interaction of the sunflower and vitamin E was positive for bone total
weights and intermuscular fat.
Abstract: An analysis is performed to study the influence of nonuniform double slot suction on a steady laminar boundary layer flow over a rotating sphere when fluid properties such as viscosity and Prandtl number are inverse linear functions of temperature. Nonsimilar solutions have been obtained from the starting point of the streamwise co-ordinate to the exact point of separation. The difficulties arising at the starting point of the streamwise co-ordinate, at the edges of the slot and at the point of separation have been overcome by applying an implicit finite difference scheme in combination with the quasi-linearization technique and an appropriate selection of the finer step sizes along the stream-wise direction. The present investigation shows that the point of ordinary separation can be delayed by nonuniform double slot suction if the mass transfer rate is increased and also if the slots are positioned further downstream. In addition, the investigation reveals that double slot suction is found to be more effective compared to a single slot suction in delaying ordinary separation. As rotation parameter increase the point of separation moves upstream direction.
Abstract: A numerical simulation of micro Poiseuille flow has
performed for rarefied and compressible flow at slip flow regimes.
The wall roughness is simulated in two cases with triangular
microelements and random micro peaks distributed on wall surfaces
to study the effects of roughness shape and distribution on flow field.
Two values of Mach and Knudsen numbers have used to investigate
the effects of rarefaction as well as compressibility. The numerical
results have also checked with available theoretical and experimental
relations and good agreements has achieved. High influence of
roughness shape can be seen for both compressible and
incompressible rarefied flows. In addition it is found that rarefaction
has more significant effect on flow field in microchannels with
higher relative roughness. It is also found that compressibility has
more significant effects on Poiseuille number when relative
roughness increases.
Abstract: Algae-based fuel are considered a promising sources
of clean energy, and because it has many advantages over traditional
biofuel, research and business ventures have driven into developing
and producing Algal-biofuel. But its production stages create a cost
structure that it is not competitive with traditional fuels. Therefore,
cost becomes the main obstacle in commercial production purpose.
However, the present research which aims at using cost structure
model, and designed MS-Dose program, to investigate the a mount of
production cost and determined the parameter had great effect on it,
second to measured the amount of contribution rate of algae in
process the pollution by capturing Co2 from air . The result generated
from the model shows that the production cost of biomass is between
$0.137 /kg for 100 ha and $0.132 /kg for 500 ha which was less than
cost of other studies, while gallon costs between $3.4 - 3.5, more
than traditional sources of oil about $1 ,which regarded as a rate of
contribution of algal in capturing CO2 from air.