Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: In this paper, we study the numerical method for solving second-order fuzzy differential equations using Adomian method under strongly generalized differentiability. And, we present an example with initial condition having four different solutions to illustrate the efficiency of the proposed method under strongly generalized differentiability.
Abstract: This paper presents comparative emission study of
newly introduced gasoline/LPG bifuel automotive engine in Indian
market. Emissions were tested as per LPG-Bharat stage III driving
cycle. Emission tests were carried out for urban cycle and extra urban
cycle. Total time for urban and extra urban cycle was 1180 sec.
Engine was run in LPG mode by using conversion system. Emissions
were tested as per standard procedure and were compared. Corrected
emissions were computed by deducting ambient reading from sample
reading. Paper describes detail emission test procedure and results
obtained. CO emissions were in the range of38.9 to 111.3 ppm. HC
emissions were in the range of 18.2 to 62.6 ppm. Nox emissions were
08 to 3.9 ppm and CO2 emissions were from 6719.2 to 8051 ppm.
Paper throws light on emission results of LPG vehicles recently
introduced in Indian automobile market. Objectives of this
experimental study were to measure emissions of engines in gasoline
& LPG mode and compare them.
Abstract: Very few studies have examined performance
implications of strategic alliance announcements in the information
technologies industry from a resource-based view. Furthermore, none
of these studies have investigated resource congruence and alliance
motive as potential sources of abnormal firm performance. This paper
extends upon current resource-based literature to discover and explore
linkages between these concepts and the practical performance of
strategic alliances. This study finds that strategic alliance
announcements have provided overall abnormal positive returns, and
that marketing alliances with marketing resource incongruence have
also contributed to significant firm performance.
Abstract: The purpose of this study was primarily assessing how important economic factors namely: The Thai export price of white rice, the exchange rate, and the world rice consumption affect the overall Thai white rice export, using historical data during the period 1989-2013 from the Thai Rice Exporters Association, and Food and Agricultural Organization of the United Nations. The co-integration method, regression analysis, and error correction model were applied to investigate the econometric model. The findings indicated that in the long-run, the world rice consumption, the exchange rate, and the Thai export price of white rice were the important factors affecting the export quantity of Thai white rice respectively, as indicated by their significant coefficients. Meanwhile, the rice export price was an important factor affecting the export quantity of Thai white rice in the short-run. This information is useful in the business, export opportunities, price competitiveness, and policymaker in Thailand.
Abstract: This paper argues that a product development exercise
involves in addition to the conventional stages, several decisions
regarding other aspects. These aspects should be addressed
simultaneously in order to develop a product that responds to the
customer needs and that helps realize objectives of the stakeholders
in terms of profitability, market share and the like. We present a
framework that encompasses these different development
dimensions. The framework shows that a product development
methodology such as the Quality Function Deployment (QFD) is the
basic tool which allows definition of the target specifications of a
new product. Creativity is the first dimension that enables the
development exercise to live and end successfully. A number of
group processes need to be followed by the development team in
order to ensure enough creativity and innovation. Secondly,
packaging is considered to be an important extension of the product.
Branding strategies, quality and standardization requirements,
identification technologies, design technologies, production
technologies and costing and pricing are also integral parts to the
development exercise. These dimensions constitute the proposed
framework. The paper also presents a mathematical model used to
calculate the design targets based on the target costing principle. The
framework is used to study a case of a new product development in
the telecommunications services sector.
Abstract: Organizational structure of the Turkish state
universities is a form of bureaucracy, a high efficient system in
rational and formal control. According to the dimensional approach
bureaucracy can occur in an organization in a degree, as some
bureaucracy characteristics can be stronger than others. In addition,
the units of an organization due to their different specific
characteristic properties can perceive the bureaucracy differently. In
the study, Hall-s Organizational Inventory, which was developed for
evaluating the degree of bureaucratization from the dimensional
perspective, is used to find out if there is a difference in the
perception of the bureaucracy between the academicians working in
three different departments and two faculties in the same university.
Abstract: In the present research, a finite element model is
presented to study the geometrical and material nonlinear behavior of
reinforced concrete plane frames considering soil-structure
interaction. The nonlinear behaviors of concrete and reinforcing steel
are considered both in compression and tension up to failure. The
model takes account also for the number, diameter, and distribution
of rebar along every cross section. Soil behavior is taken into
consideration using four different models; namely: linear-, nonlinear
Winkler's model, and linear-, nonlinear continuum model. A
computer program (NARC) is specially developed in order to
perform the analysis. The results achieved by the present model show
good agreement with both theoretical and experimental published
literature. The nonlinear behavior of a rectangular frame resting on
soft soil up to failure using the proposed model is introduced for
demonstration.
Abstract: This research is to study the types of products and
services that employs 'ambient media and respective techniques in its
advertisement materials. Data collection has been done via analyses of a total of 62 advertisements that employed ambient media
approach in Thailand during the years 2004 to 2011. The 62 advertisement were qualifying advertisements of the Adman Awards
& Symposium under the category of Outdoor & Ambience. Analysis
results reveal that there is a total of 14 products and services that
chooses to utilize ambient media in its advertisement. Amongst all ambient media techniques, 'intrusion' uses the value of a medium in
its representation of content most often. Following intrusion is 'interaction', where consumers are invited to participate and interact
with the advertising materials. 'Illusion' ranks third in its ability to subject the viewers to distortions of reality that makes the division
between reality and fantasy less clear.
Abstract: From past many decades human beings are suffering
from plethora of natural disasters. Occurrence of disasters is a
frequent process; it changes conceptual myths as more and more
advancement are made. Although we are living in technological era
but in developing countries like Pakistan disasters are shaped by
socially constructed roles. The need is to understand the most
vulnerable group of society i.e. females; their issues are complex in
nature because of undermined gender status in the society. There is a
need to identify maximum issues regarding females and to enhance
the achievement of millennium development goals (MDGs). Gender
issues are of great concern all around the globe including Pakistan.
Here female visibility in society is low, and also during disasters, the
failure to understand the reality that concentrates on double burden
including productive and reproductive care. Women have to
contribute a lot in society so we need to make them more disaster
resilient. For this non-structural measures like awareness, trainings
and education must be carried out. In rural and in urban settings in
any disaster like earthquake or flood, elements like gender
perspective, their age, physical health, demographic issues contribute
towards vulnerability. In Pakistan the gender issues in disasters were
of less concern before 2005 earthquake and 2010 floods. Significant
achievements are made after 2010 floods when gender and child cell
was created to provide all facilities to women and girls. The aim of
the study is to highlight all necessary facilities in a disaster to build
coping mechanism in females from basic rights till advance level
including education.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: Automatic Vehicle Identification (AVI) has many
applications in traffic systems (highway electronic toll collection, red
light violation enforcement, border and customs checkpoints, etc.).
License Plate Recognition is an effective form of AVI systems. In
this study, a smart and simple algorithm is presented for vehicle-s
license plate recognition system. The proposed algorithm consists of
three major parts: Extraction of plate region, segmentation of
characters and recognition of plate characters. For extracting the
plate region, edge detection algorithms and smearing algorithms are
used. In segmentation part, smearing algorithms, filtering and some
morphological algorithms are used. And finally statistical based
template matching is used for recognition of plate characters. The
performance of the proposed algorithm has been tested on real
images. Based on the experimental results, we noted that our
algorithm shows superior performance in car license plate
recognition.
Abstract: We propose a reduced-ordermodel for the instantaneous
hydrodynamic force on a cylinder. The model consists of a system of
two ordinary differential equations (ODEs), which can be integrated
in time to yield very accurate histories of the resultant force and
its direction. In contrast to several existing models, the proposed
model considers the actual (total) hydrodynamic force rather than its
perpendicular or parallel projection (the lift and drag), and captures
the complete force rather than the oscillatory part only. We study
and provide descriptions of the relationship between the model
parameters, evaluated utilizing results from numerical simulations,
and the Reynolds number so that the model can be used at any
arbitrary value within the considered range of 100 to 500 to provide
accurate representation of the force without the need to perform timeconsuming
simulations and solving the partial differential equations
(PDEs) governing the flow field.
Abstract: This paper studies the duration or survival time of commercial banks active in the Moscovian three month Rouble deposits market, during the 1994-1997 period. The privatization process of the Russian commercial banking industry, after the 1988 banking reform, caused a massive entry of new banks followed by a period of high rates of exit. As a consequence, many firms went bankrupt without refunding their deposits. Therefore, both for the banks and for the banks- depositors, it is of interest to analyze which are the significant characteristics that motivate the exit or the closing of the bank. We propose a different methodology based on penalized weighted least squares which represents a very general, flexible and innovative approach for this type of analysis. The more relevant results are that smaller banks exit sooner, banks that enter the market in the last part of the study have shorter durations. As expected, the more experienced banks have a longer duration in the market. In addition, the mean survival time is lower for banks which offer extreme interest rates.
Abstract: Several methods have been proposed for color image
compression but the reconstructed image had very low signal to noise
ratio which made it inefficient. This paper describes a lossy
compression technique for color images which overcomes the
drawbacks. The technique works on spatial domain where the pixel
values of RGB planes of the input color image is mapped onto two
dimensional planes. The proposed technique produced better results
than JPEG2000, 2DPCA and a comparative study is reported based
on the image quality measures such as PSNR and MSE.Experiments
on real time images are shown that compare this methodology with
previous ones and demonstrate its advantages.
Abstract: This paper presents the outcomes of a qualitative
study which aims to investigate the pedagogical potentials of serious
games in the preparation of future teachers. The authors discuss the
existing problems and barriers associated with the organization of
teaching practices in Bulgaria as part of the pre-service teacher
training, as well as the attitudes and perceptions of the interviewed
academics, teachers and trainees concerning the integration of serious
games in the teaching practicum. The study outcomes strongly
confirm the positive attitudes of the respondents to the introduction
of virtual learning environments for the development of professional
skills of future teachers as a supplement to the traditional forms of
education. Through the inclusion of serious games it is expected to
improve the quality of practical training of pre-service teachers as
they overcome many of the problems identified in the existing
teaching practices. The outcomes of the study will inform the design
of the educational simulation software which is part of the project
SimAula Tomorrow's Teachers Training.
Abstract: Isobaric vapor-liquid equilibrium measurements are
reported for binary mixture of 2-Methyltetrahydrofuran and Cumene
at 97.3 kPa. The data were obtained using a vapor recirculating type
(modified Othmer's) equilibrium still. The mixture shows slight
negative deviation from ideality. The system does not form an
azeotrope. The experimental data obtained in this study are
thermodynamically consistent according to the Herington test. The
activity coefficients have been satisfactorily correlated by means of
the Margules, and NRTL equations. Excess Gibbs free energy has
been calculated from the experimental data. The values of activity
coefficients have also been obtained by the UNIFAC group
contribution method.
Abstract: Water is the main component of biological processes.
Water management is important to obtain higher productivity. In this
study, some of the yield components were investigated together with
different drought levels. Four chickpea genotypes (CDC Frontier,
CDC Luna, Sawyer and Sierra) were grown in pots with 3 different
irrigation levels (a dose of 17.5 ml, 35 ml and 70 ml for each pot per
day) after three weeks from sowing. In the research, flowering, pod
set, pod per plant, fertile pod, double seed/pod, stem diameter, plant
weight, seed per plant, 1000 seed weight, seed diameter, vegetation
length and weekly plant height were measured. Consequently,
significant differences were observed on all the investigated
characteristics owing to genotypes (except double seed/pod and stem
diameter), water levels (except first pod, seed weight and height on
3rd week) and genotype x water level interaction (except first pod,
double seed/pod, seed weight and height).
Abstract: This paper presents the possibilities of using Weibull statistical distribution in modeling the distribution of defects in ERP systems. There follows a case study, which examines helpdesk records of defects that were reported as the result of one ERP subsystem upgrade. The result of the applied modeling is in modeling the reliability of the ERP system from a user perspective with estimated parameters like expected maximum number of defects in one day or predicted minimum of defects between two upgrades. Applied measurement-based analysis framework is proved to be suitable in predicting future states of the reliability of the observed ERP subsystems.
Abstract: Renewable water resources are crucial production
variables in arid and semi-arid regions where intensive agriculture is
practiced to meet ever-increasing demand for food and fiber. This is
crucial for the Dez and Moghan command areas where water delivery
problems and adverse environmental issues are widespread. This
paper aims to identify major problems areas using on-farm surveys of
200 farmers, agricultural extensionists and water suppliers which was
complemented by secondary data and field observations during 2010-
2011 cultivating season. The SPSS package was used to analyze and
synthesis data. Results indicated inappropriate canal operations in
both schemes, though there was no unanimity about the underlying
causes. Inequitable and inflexible distribution was found to be rooted
in deficient hydraulic structures particularly in the main and
secondary canals. The inadequacy and inflexibility of water
scheduling regime was the underlying causes of recurring pest and
disease spread which often led to the decline of crop yield and
quality, although these were not disputed, the water suppliers were
not prepared to link with the deficiencies in the operation of the main
and secondary canals. They rather attributed these to the prevailing
salinity; alkalinity, water table fluctuations and leaching of the
valuable agro-chemical inputs from the plants- route zone with farreaching
consequences. Examples of these include the pollution of
ground and surface resources due to over-irrigation at the farm level
which falls under the growers- own responsibility. Poor irrigation
efficiency and adverse environmental problems were attributed to
deficient and outdated farming practices that were in turn rooted in
poor extension programs and irrational water charges.