Abstract: In this study, the precision heading process of
spur gears has been investigated by means of numerical
analysis. The effect of some parameters such as teeth number
and module on the forming force and material flow were
presented. The simulation works were performed rigid-plastic
finite element method using DEFORM 3D software. In order
to validate the estimated numerical results, they were
compared with those obtained experimentally during heading
of spur gear using lead as a model material. Results showed
that the optimum number of gear teeth is between 10 to 20,
that is because of being the specific pressure in its minimum
value.
Abstract: In this study, the dispersed model is used to predict
gas phase concentration, liquid drop concentration. The venturi
scrubber efficiency is calculated by gas phase concentration. The
modified model has been validated with available experimental data
of Johnstone, Field and Tasler for a range of throat gas velocities,
liquid to gas ratios and particle diameters and is used to study the
effect of some design parameters on collection efficiency.
Abstract: An actual power plant, which is the power plant of Iron and Steel Factory at Misurata city in Libya , has been modeled using Matlab in order to compare its results to the actual results of the actual cycle. This paper concentrates on two factors:
a- The comparison between exergy losses in the actual cycle and the modeled cycle.
b- The effect of extracting pressure on temperature water at boiler inlet.
Closed heat exchangers used in this plant have been substituted by open heat exchangers in the current study of the modeled power plant and the required changes in the pressure have been considered. In the following investigation the two points mentioned above are taken in consideration.
Abstract: Accounts of language acquisition differ significantly in their treatment of the role of prediction in language learning. In particular, nativist accounts posit that probabilistic learning about words and word sequences has little to do with how children come to use language. The accuracy of this claim was examined by testing whether distributional probabilities and frequency contributed to how well 3-4 year olds repeat simple word chunks. Corresponding chunks were the same length, expressed similar content, and were all grammatically acceptable, yet the results of the study showed marked differences in performance when overall distributional frequency varied. It was found that a distributional model of language predicted the empirical findings better than a number of other models, replicating earlier findings and showing that children attend to distributional probabilities in an adult corpus. This suggested that language is more prediction-and-error based, rather than on abstract rules which nativist camps suggest.
Abstract: Intradiscal and intervertebral pressure transducers
were developed. They were used to map the pressures in the nucleus
and within the annulus of the human spinal segments. Their stressrelaxation
were recorded over a period of time for nucleus
pressure, applied load, and peripherial strain against time. The
results show that for normal discs, pressures in the nucleus are
viscoelastic in nature with the applied compressive load.
Mechanical strains which develop around the periphery of the
vertebral body are also viscoelastic with the applied compressive
load. Applied compressive load against time also shows viscoelastic
behavior. However, annulus does not respond viscoelastically with
the applied load. It showed a linear response to compressive loading.
Abstract: A novel concept to balance and tradeoff between
make-to-stock and make-to-order has been hybrid MTS/MTO production context. One of the most important decisions involved in
the hybrid MTS/MTO environment is determining whether a product
is manufactured to stock, to order, or hybrid MTS/MTO strategy. In this paper, a model based on analytic network process is developed to tackle the addressed decision. Since the regarded decision deals with
the uncertainty and ambiguity of data as well as experts- and
managers- linguistic judgments, the proposed model is equipped with
fuzzy sets theory. An important attribute of the model is its generality due to diverse decision factors which are elicited from the
literature and developed by the authors. Finally, the model is validated by applying to a real case study to reveal how the proposed
model can actually be implemented.
Abstract: A new observer based fault detection and diagnosis
scheme for predicting induction motors- faults is proposed in this
paper. Prediction of incipient faults, using different variants of
Kalman filter and their relative performance are evaluated. Only soft
faults are considered for this work. The data generation, filter
convergence issues, hypothesis testing and residue estimates are
addressed. Simulink model is used for data generation and various
types of faults are considered. A comparative assessment of the
estimates of different observers associated with these faults is
included.
Abstract: The higher compounded growth rates coupled with
favourable demographics in emerging markets portend abundant
opportunities for multinational organizations. With many
organizations competing for talent in these growing markets, their
ability to succeed will depend on their understanding of local
workforce needs and aspirations. Using data from the Towers Watson
2010 Global Workforce Study, this paper highlights differences in
employee engagement, turnover risks, and attraction and retention
drivers between the two markets. Apart from looking at the
traditional drivers of employee engagement, the study also explores
the value placed by employees on elements like a strong senior
leadership, managerial capabilities and career advancement
opportunities. Results reveal that emerging markets employees seem
to be more engaged and value the non-traditional elements more
highly than the developed markets employees.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and Choram
are the most important and populated cities in this area. The study
was undertaken to assess the status of water quality in the urban areas
of the Kowsar dam. A total of 28 water samples were collected from
6 stations on surface water and 1 station from groundwater on the
watershed of the Kowsar dam. All the samples were analyzed for Ni
concentration using standard procedures. The results were compared
with other national and international standards. Among the analyzed
samples, as the maximum value of Nickel (0.01 mg/L) was observed
on the station 2 at the autumn 2010, all the samples analyzed were
within the maximum admissible limits by the United States
Environmental Protection Agency, EU, WHO and the Iranian. In
general results of the present study have shown that a Ni mean value
of station No. 2 with 0.006 mg/L is higher than the other stations. Ni
level of all samples and stations have had normal values and this is an
indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watersheds.
Abstract: Nano MgO has been synthesized by hydration and
dehydration method by modifies the commercial MgO. The prepared
MgO had been investigated as a heterogeneous base catalyst for
transesterification process for biodiesel production using palm oil.
TGA, FT-IR and XRD results obtained from this study lie each other
and proved in the formation of nano MgO from decomposition of
Mg(OH)2. This study proved that the prepared nano MgO was a
better base transesterification catalyst compared to commercial MgO.
The nano MgO calcined at 600ºC had gives the highest conversion of
51.3% of palm oil to biodiesel.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: This research aimed to study correlation between
work satisfaction and organization core value of officers in
Waterworks Authority, Bangkean Branch. Sample group of the study
was 112 officers who worked in the Waterworks Authority,
Bangkean Branch. Questionnaires were employed as a research tools,
while, Percentage, Mean, Standard Deviation, T-test, One-way
ANOVA, and Pearson Product Moment Correlation were claimed as
statistics used in this study. Researcher found that overall and
individual aspects of work satisfaction namely, work characteristic,
work progress, and colleagues significantly correlated with
organization core value in aspect of perception in choice of work at
0.5, 0.01, and 0.01 respectively. Also, such aspects were compatible
with income at .05 which indicated the low level of correlation, mid
low correlation respectively at the same direction, same direction,
opposite direction, and same direction, correspondingly.
Abstract: The aims of this study were to compare the
differences of being good membership behavior among faculties and
staffs of Suan Sunandha Rajabhat University with different sex, age,
income, education, marital status, and working period, and
investigate the relationships between organizational commitment and
being good membership behavior. The research methodology
employed a questionnaire as a quantitative method. The respondents
were 305 faculties and staffs of Suan Sunandha Rajabhat University.
This research used Percentage, Mean, Standard Deviation, t-test,
One-Way ANOVA Analysis of Variance, and Pearson’s Product
Moment Correlation Coefficient in data analysis. The results showed
that organizational commitment among faculties and staffs of Suan
Sunandha Rajabhat University was at a high level. In addition,
differences in sex, age, income, education, marital status, and
working period revealed differences in being good membership
behavior. The results also indicated that organizational commitment
was significantly related to being good membership behavior.
Abstract: In the normal operation conditions of a pico satellite,
conventional Unscented Kalman Filter (UKF) gives sufficiently good
estimation results. However, if the measurements are not reliable
because of any kind of malfunction in the estimation system, UKF
gives inaccurate results and diverges by time. This study, introduces
Robust Unscented Kalman Filter (RUKF) algorithms with the filter
gain correction for the case of measurement malfunctions. By the use
of defined variables named as measurement noise scale factor, the
faulty measurements are taken into the consideration with a small
weight and the estimations are corrected without affecting the
characteristic of the accurate ones. Two different RUKF algorithms,
one with single scale factor and one with multiple scale factors, are
proposed and applied for the attitude estimation process of a pico
satellite. The results of these algorithms are compared for different
types of measurement faults in different estimation scenarios and
recommendations about their applications are given.
Abstract: In this study is presented a general methodology to
predict the performance of a continuous near-critical fluid extraction
process to remove compounds from aqueous solutions using hollow
fiber membrane contactors. A comprehensive 2D mathematical
model was developed to study Porocritical extraction process. The
system studied in this work is a membrane based extractor of ethanol
and acetone from aqueous solutions using near-critical CO2.
Predictions of extraction percentages obtained by simulations have
been compared to the experimental values reported by Bothun et al.
[5]. Simulations of extraction percentage of ethanol and acetone
show an average difference of 9.3% and 6.5% with the experimental
data, respectively. More accurate predictions of the extraction of
acetone could be explained by a better estimation of the transport
properties in the aqueous phase that controls the extraction of this
solute.
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Recent quasi-experimental evaluation of the Canadian Active Labour Market Policies (ALMP) by Human Resources and Skills Development Canada (HRSDC) has provided an opportunity to examine alternative methods to estimating the incremental effects of Employment Benefits and Support Measures (EBSMs) on program participants. The focus of this paper is to assess the efficiency and robustness of inverse probability weighting (IPW) relative to kernel matching (KM) in the estimation of program effects. To accomplish this objective, the authors compare pairs of 1,080 estimates, along with their associated standard errors, to assess which type of estimate is generally more efficient and robust. In the interest of practicality, the authorsalso document the computationaltime it took to produce the IPW and KM estimates, respectively.
Abstract: Computers are increasingly being used as educational
tools in elementary/primary schools worldwide. A specific
application of such computer use, is that of multimedia games, where
the aim is to combine pedagogy and entertainment. This study
reports on a case-study whereby an educational multimedia game has
been developed for use by elementary school children. The stages of
the application-s design, implementation and evaluation are
presented. Strengths of the game are identified and discussed, and its
weaknesses are identified, allowing for suggestions for future redesigns.
The results show that the use of games can engage children
in the learning process for longer periods of time with the added
benefit of the entertainment factor.