Abstract: In this paper, using a model transformation approach a system of linear delay differential equations (DDEs) with multiple delays is converted to a non-delayed initial value problem. The variational iteration method (VIM) is then applied to obtain the approximate analytical solutions. Numerical results are given for several examples involving scalar and second order systems. Comparisons with the classical fourth-order Runge-Kutta method (RK4) verify that this method is very effective and convenient.
Abstract: An organic bulk heterojunction (BHJ) was fabricated using a blended film containing Copper (II) tetrakis(4-acumylphenoxy) phthalocyanine (Tc-CuPc) along with [6,6]-Phenyl C61 butyric acid methyl ester (PCBM). Weight ratio between Tc-CuPc and PCBM was 1:1. The electrical properties of Tc-CuPc: PCBM BHJ were examined. Rectifying nature of the BHJ was displayed by current-voltage (I-V) curves, recorded in dark and at various temperatures. At low voltages, conduction was ohmic succeeded by space-charge limiting current (SCLC) conduction at higher voltages in which exponential trap distribution was dominant. Series resistance, shunt resistance, ideality factor, effective barrier height and mobility at room temperature were found to be 526 4, 482 k4, 3.7, 0.17 eV and 2×10-7 cm2V-1s-1 respectively. Temperature effect towards different BHJ parameters was observed under dark condition.
Abstract: Alkali treated oil palm empty fruit bunch (EFB) fibres
(TEFBF) and untreated EFBF fibers (UEFBF) were incorporated in
polypropylene (PP) with and without malic anhydride grafted PP
(MAPP) and magnesium hydroxide as flame retardant (FR) to
produce TEFBF-PP and UEFBF-PP composites by the melt casting
method. The composites were characterized by mechanical and
burning tests along with a scanning electron microscope and Fourier
transform infrared spectroscopy. The significant improvement in
flexural modulus (133%) and flame retardant property (60%) of
TEFBF-PP composite with MAPP and FR is observed. The improved
mechanical property is discussed by the development of encapsulated
textures.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: The effect of SnO2 surface modification by Ag nanoclusters, synthesized by SILD method, on the operating characteristics of thin film gas sensors was studied and models for the promotional role of Ag additives were discussed. It was found that mentioned above approach can be used for improvement both the sensitivity and the rate of response of the SnO2-based gas sensors to CO and H2. At the same time, the presence of the Ag clusters on the surface of SnO2 depressed the sensor response to ozone.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.
Abstract: Organic Flash Cycle (OFC) has potential of improving
efficiency for recovery of low temperature heat sources mainly due to
reducing temperature mismatch in the heat exchanger. In this work
exergetical performance analysis of ORC is conducted for recovery of
low grade heat source. Effects of system parameters such as flash
evaporation temperature or heating temperature are theoretically
investigated on the exergy destructions (anergies) at various
components of the system as well as exergy efficiency. Results show
that exergy efficiency has a peak with respect to the flash temperature,
and the optimum flash temperature increases with the heating
temperature. The component where the largest exergy destruction
occurs varies with the flash temperature or heating temperature.
Abstract: In the present paper, a set of parametric FE stress
analyses is carried out for two-planar welded tubular DKT-joints
under two different axial load cases. Analysis results are used to
present general remarks on the effect of geometrical parameters on
the stress concentration factors (SCFs) at the inner saddle, outer
saddle, toe, and heel positions on the main (outer) brace. Then a new
set of SCF parametric equations is developed through nonlinear
regression analysis for the fatigue design of two-planar DKT-joints.
An assessment study of these equations is conducted against the
experimental data; and the satisfaction of the criteria regarding the
acceptance of parametric equations is checked. Significant effort has
been devoted by researchers to the study of SCFs in various uniplanar
tubular connections. Nevertheless, for multi-planar joints
covering the majority of practical applications, very few
investigations have been reported due to the complexity and high
cost involved.
Abstract: The effect of a chiral bianisotropic substrate on the
complex resonant frequency of a rectangular microstrip resonator has
been studied on the basis of the integral equation formulation. The
analysis is based on numerical resolution of the integral equation
using Galerkin procedure for moment method in the spectral domain.
This work aim first to study the effect of the chirality of a
bianisotopic substrate upon the resonant frequency and the half
power bandwidth, second the effect of a magnetic anisotropy via an
asymptotic approach for very weak substrate upon the resonant
frequency and the half power bandwidth has been investigated. The
obtained results are compared with previously published work [11-9],
they were in good agreement.
Abstract: The aim of this study is to emphasize the opportunities in space design under the aspect of HCI as performance areas. HCI is a multidisciplinary approach that could be identified in many different areas. The aesthetical reflections of HCI by virtual reality in space design are the high-tech solutions of the new innovations as computational facilities by artistic features. The method of this paper is to identify the subject in 3 main parts. In the first part a general approach and definition of interactivity on the basis of space design; in the second part the concept of multimedia interactive theater by some chosen samples from the world and interactive design aspects; in the third part the samples from Turkey will be identified by stage designing principles. In the results it could be declared that the multimedia database is the virtual approach of theatre stage designing regarding interactive means by computational facilities according to aesthetical aspects. HCI is mostly identified in theatre stages as computational intelligence under the affect of interactivity.
Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: The effect of the number of quantum dot (QD) layers
on the saturated gain of doped QD semiconductor optical amplifiers
(SOAs) has been studied using multi-population coupled rate
equations. The developed model takes into account the effect of
carrier coupling between adjacent layers. It has been found that
increasing the number of QD layers (K) increases the unsaturated
optical gain for K
Abstract: Soil organic carbon (SOC) plays a key role in soil
fertility, hydrology, contaminants control and acts as a sink or source
of terrestrial carbon content that can affect the concentration of
atmospheric CO2. SOC supports the sustainability and quality of
ecosystems, especially in semi-arid region. This study was
conducted to determine relative importance of 13 different
exploratory climatic, soil and geometric factors on the SOC contents
in one of the semiarid watershed zones in Iran. Two methods
canonical discriminate analysis (CDA) and feed-forward back
propagation neural networks were used to predict SOC. Stepwise
regression and sensitivity analysis were performed to identify
relative importance of exploratory variables. Results from sensitivity
analysis showed that 7-2-1 neural networks and 5 inputs in CDA
models output have highest predictive ability that explains %70 and
%65 of SOC variability. Since neural network models outperformed
CDA model, it should be preferred for estimating SOC.
Abstract: Search for a tertiary substructure that geometrically
matches the 3D pattern of the binding site of a well-studied protein provides a solution to predict protein functions. In our previous work,
a web server has been built to predict protein-ligand binding sites
based on automatically extracted templates. However, a drawback of such templates is that the web server was prone to resulting in many
false positive matches. In this study, we present a sequence-order constraint to reduce the false positive matches of using automatically
extracted templates to predict protein-ligand binding sites. The binding site predictor comprises i) an automatically constructed template library and ii) a local structure alignment algorithm for
querying the library. The sequence-order constraint is employed to
identify the inconsistency between the local regions of the query protein and the templates. Experimental results reveal that the sequence-order constraint can largely reduce the false positive matches and is effective for template-based binding site prediction.
Abstract: School leadership is commonly considered to have a
significant influence on school effectiveness and improvement.
Effective school leaders are expected to successfully introduce and
support change and innovation at the school unit. Despite an
abundance of studies on educational leadership, very few studies
have provided evidence on the link between leadership models, and
specific educational and school outcomes. This is true of a popular
contemporary approach to leadership, namely, distributed leadership.
The paper provides an overview of research findings on the effect of
distributed leadership on educational outcomes. The theoretical basis
for this approach to leadership is presented, with reference to
methodological and research limitations. The paper discusses
research findings and draws their implications for educational
research on school leadership.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: Hybrid knowledge model is suggested as an underlying
framework for product development management. It can support such
hybrid features as ontologies and rules. Effective collaboration in
product development environment depends on sharing and reasoning
product information as well as engineering knowledge. Many studies
have considered product information and engineering knowledge.
However, most previous research has focused either on building the
ontology of product information or rule-based systems of engineering
knowledge. This paper shows that F-logic based knowledge model can
support such desirable features in a hybrid way.
Abstract: In the visual servoing systems, the data obtained by
Visionary is used for controlling robots. In this project, at first the
simulator which was proposed for simulating the performance of a
6R robot before, was examined in terms of software and test, and in
the proposed simulator, existing defects were obviated. In the first
version of simulation, the robot was directed toward the target object only in a Position-based method using two cameras in the
environment. In the new version of the software, three cameras were used simultaneously. The camera which is installed as eye-inhand on the end-effector of the robot is used for visual servoing in a
Feature-based method. The target object is recognized according to
its characteristics and the robot is directed toward the object in compliance with an algorithm similar to the function of human-s
eyes. Then, the function and accuracy of the operation of the robot are examined through Position-based visual servoing method using
two cameras installed as eye-to-hand in the environment. Finally, the obtained results are tested under ANSI-RIA R15.05-2 standard.
Abstract: This paper presents one of the best applications of wireless sensor network for campus Monitoring. With the help of PIR sensor, temperature sensor and humidity sensor, effective utilization of energy resources has been implemented in one of rooms of Sharda University, Greater Noida, India. The RISC microcontroller is used here for analysis of output of sensors and providing proper control using ZigBee protocol. This wireless sensor module presents a tremendous power saving method for any campus
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.