Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: A active inductor in CMOS techonology with a supply voltage of 1.8V is presented. The value of the inductance L can be in the range from 0.12nH to 0.25nH in high frequency(HF). The proposed active inductor is designed in TSMC 0.18-um CMOS technology. The power dissipation of this inductor can retain constant at all operating frequency bands and consume around 20mW from 1.8V power supply. Inductors designed by integrated circuit occupy much smaller area, for this reason,attracted researchers attention for more than decade. In this design we used Advanced Designed System (ADS) for simulating cicuit.
Abstract: In this study, the Taguchi method was used to optimize the effect of HALO structure or halo implant variations on threshold voltage (VTH) and leakage current (ILeak) in 45nm p-type Metal Oxide Semiconductor Field Effect Transistors (MOSFETs) device. Besides halo implant dose, the other process parameters which used were Source/Drain (S/D) implant dose, oxide growth temperature and silicide anneal temperature. This work was done using TCAD simulator, consisting of a process simulator, ATHENA and device simulator, ATLAS. These two simulators were combined with Taguchi method to aid in design and optimize the process parameters. In this research, the most effective process parameters with respect to VTH and ILeak are halo implant dose (40%) and S/D implant dose (52%) respectively. Whereas the second ranking factor affecting VTH and ILeak are oxide growth temperature (32%) and halo implant dose (34%) respectively. The results show that after optimizations approaches is -0.157V at ILeak=0.195mA/μm.
Abstract: This paper presents the development of an electricity simulation model taking into account electrical network constraints, applied on the Belgian power system. The base of the model is optimizing an extensive Unit Commitment (UC) problem through the use of Mixed Integer Linear Programming (MILP). Electrical constraints are incorporated through the implementation of a DC load flow. The model encloses the Belgian power system in a 220 – 380 kV high voltage network (i.e., 93 power plants and 106 nodes). The model features the use of pumping storage facilities as well as the inclusion of spinning reserves in a single optimization process. Solution times of the model stay below reasonable values.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: In this paper we present a new multichannel high
voltage driver box to connect up to six MOEMS mirror devices to it that have resonant and also quasistatically driven actuating electrodes. It is possible to drive all resonant axes synchronously
while the amplitude of them can individually be controlled by separate microcontrollers that also operate the quasistatic axes.
Circuit simulations are compared with the measurements done on the
real system and also show the robust driving performance of a
MOEMS mirror.
Abstract: RF performance of SOI CMOS device has attracted
significant amount of interest recently. In order to improve RF
parameters, Strained Si/Relaxed Si0.8Ge0.2 investigated as a
replacement for Si technology .Enhancement of carrier mobility
associated with strain engineering makes Strained Si a promising
candidate for improving RF performance of CMOS technology.
From the simulation, the cut-off frequency is estimated to be 224
GHZ, whereas in SOI at similar bias is about 188 GHZ. Therefore,
Strained Si exhibits 19% improvement in cut-off frequency over
similar Si counterpart. In this paper, Ion/Ioff ratio is studied as one of
the key parameters in logic and digital application. Strained Si/SiGe
demonstrates better Ion/Ioff characteristic than SOI, in similar channel
length of 100 nm.Another important key analog figures of merit such
as Early Voltage (VEA) ,transconductance vs drain current (gm /Ids)
are studied. They introduce the efficiency of the devices to convert
dc power into ac frequency.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: Photovoltaic power generation forecasting is an
important task in renewable energy power system planning and
operating. This paper explores the application of neural networks
(NN) to study the design of photovoltaic power generation
forecasting systems for one week ahead using weather databases
include the global irradiance, and temperature of Ghardaia city
(south of Algeria) using a data acquisition system. Simulations were
run and the results are discussed showing that neural networks
Technique is capable to decrease the photovoltaic power generation
forecasting error.
Abstract: In this paper, the details of an experimental method to measure the clamping force value at bolted connections due to application of wrenching torque to tighten the nut have been presented. A simplified bolted joint including a holed plate with a single bolt was considered to carry out the experiments. This method was designed based on Hooke-s law by measuring compressive axial strain of a steel bush placed between the nut and the plate. In the experimental procedure, the values of clamping force were calculated for seven different levels of applied torque, and this process was repeated three times for each level of the torque. Moreover, the effect of lubrication of threads on the clamping value was studied using the same method. In both conditions (dry and lubricated threads), relation between the torque and the clamping force have been displayed in graphs.
Abstract: This purpose of this paper is to develop and validate a
model to accurately predict the cell temperature of a PV module that
adapts to various mounting configurations, mounting locations, and
climates while only requiring readily available data from the module
manufacturer. Results from this model are also compared to results
from published cell temperature models. The models were used to
predict real-time performance from a PV water pumping systems in
the desert of Medenine, south of Tunisia using 60-min intervals of
measured performance data during one complete year. Statistical
analysis of the predicted results and measured data highlight possible
sources of errors and the limitations and/or adequacy of existing
models, to describe the temperature and efficiency of PV-cells and
consequently, the accuracy of performance of PV water pumping
systems prediction models.
Abstract: This paper present the harmonic elimination of hybrid
multilevel inverters (HMI) which could be increase the number of
output voltage level. Total Harmonic Distortion (THD) is one of the
most important requirements concerning performance indices.
Because of many numbers output levels of HMI, it had numerous
unknown variables of eliminate undesired individual harmonic and
THD nonlinear equations set. Optimized harmonic stepped waveform
(OHSW) is solving switching angles conventional method, but most
complicated for solving as added level. The artificial intelligent
techniques are deliberation to solve this problem. This paper presents
the Particle Swarm Optimization (PSO) technique for solving
switching angles to get minimum THD and eliminate undesired
individual harmonics of 15-levels hybrid multilevel inverters.
Consequently it had many variables and could eliminate numerous
harmonics. Both advantages including high level of inverter and
Particle Swarm Optimization (PSO) are used as powerful tools for
harmonics elimination.
Abstract: Voltage flicker problems have long existed in several
of the distribution areas served by the Taiwan Power Company. In
the past, those research results indicating that the estimated ΔV10
value based on the conventional method is significantly smaller than
the survey value. This paper is used to study the relationship between
the voltage flicker problems and harmonic power variation for the
power system with electric arc furnaces. This investigation discussed
thought the effect of harmonic power fluctuation with flicker
estimate value. The method of field measurement, statistics and
simulation is used. The survey results demonstrate that 10 ΔV
estimate must account for the effect of harmonic power variation.
Abstract: This paper presents a new true RMS-to-DC converter
circuit based on a square-root-domain squarer/divider. The circuit is
designed by employing up-down translinear loop and using of
MOSFET transistors that operate in strong inversion saturation
region. The converter offer advantages of two-quadrant input current,
low circuit complexity, low supply voltage (1.2V) and immunity
from the body effect. The circuit has been simulated by HSPICE.
The simulation results are seen to conform to the theoretical analysis
and shows benefits of the proposed circuit.
Abstract: In Peer-to-Peer service networks, where peers offer any kind of publicly available services or applications, intuitive navigation through all services in the network becomes more difficult as the number of services increases. In this article, a concept is discussed that enables users to intuitively browse and use large scale P2P service networks. The concept extends the idea of creating virtual 3D-environments solely based on Peer-to-Peer technologies. Aside from browsing, users shall have the possibility to emphasize services of interest using their own semantic criteria. The appearance of the virtual world shall intuitively reflect network properties that may be of interest for the user. Additionally, the concept comprises options for load- and traffic-balancing. In this article, the requirements concerning the underlying infrastructure and the graphical user interface are defined. First impressions of the appearance of future systems are presented and the next steps towards a prototypical implementation are discussed.
Abstract: Nowadays it is a trend for electronic circuit designers to
integrate all system components on a single-chip. This paper proposed
the design of a single-chip proportional to absolute temperature
(PTAT) sensor including a voltage reference circuit using CEDEC
0.18m CMOS Technology. It is a challenge to design asingle-chip
wide range linear response temperature sensor for many applications.
The channel widths between the compensation transistor and the
reference transistor are critical to design the PTAT temperature sensor
circuit. The designed temperature sensor shows excellent linearity
between -100°C to 200° and the sensitivity is about 0.05mV/°C.
The chip is designed to operate with a single voltage source of 1.6V.
Abstract: In this paper, in order to investigate the effects of
photovoltaic system introduction to detached houses in Japan, two
kinds of works were done. Firstly, the hourly generation amount of a
4.2kW photovoltaic system were simulated in 46 cities to investigate
the potential of the system in different regions in Japan using a
simulation model of photovoltaic system. Secondly, based on the
simulated electricity generation amount, the energy saving, the
environmental and the economic effect of the photovoltaic system
were examined from hourly to annual timescales, based upon
calculations of typical electricity, heating, cooling and hot water
supply load profiles for Japanese dwellings. The above analysis was
carried out using a standard year-s hourly weather data for the
different city provided by the Expanded AMeDAS Weather Data
issued by AIJ (Architectural Institute of Japan).