Abstract: This work presents an approach for the measurement
of mutual inductance on near field inductive coupling. The mutual
inductance between inductive circuits allows the simulation of energy
transfer from reader to tag, that can be used in RFID and powerless
implantable devices. It also allows one to predict the maximum
voltage in the tag of the radio-frequency system.
Abstract: This paper proposes a Particle Swarm Optimization
(PSO) based technique for the optimal allocation of Distributed
Generation (DG) units in the power systems. In this paper our aim is
to decide optimal number, type, size and location of DG units for
voltage profile improvement and power loss reduction in distribution
network. Two types of DGs are considered and the distribution load
flow is used to calculate exact loss. Load flow algorithm is combined
appropriately with PSO till access to acceptable results of this
operation. The suggested method is programmed under MATLAB
software. Test results indicate that PSO method can obtain better
results than the simple heuristic search method on the 30-bus and 33-
bus radial distribution systems. It can obtain maximum loss reduction
for each of two types of optimally placed multi-DGs. Moreover,
voltage profile improvement is achieved.
Abstract: In this paper, a alternative structure method for
continuous time sigma delta modulator is presented. In this
modulator for implementation of integrators in loop filter second
generation current conveyors are employed. The modulator is
designed in CMOS technology and features low power consumption
(65db),
and with 180khZ bandwidth. Simulation results confirm that this
design is suitable for data converters.
Abstract: This paper describes a three-dimensional thermal
model of the current path included in the low voltage power circuit
breakers. The model can be used to analyse the thermal behaviour of
the current path during both steady-state and transient conditions.
The current path lengthwise temperature distribution and timecurrent
characteristic of the terminal connections of the power circuit
breaker have been obtained. The influence of the electric current and
voltage drop on main electric contact of the circuit breaker has been
investigated. To validate the three-dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: This paper proposes an active soft-switching circuit for
bridge converters aiming to improve the power conversion efficiency.
The proposed circuit achieves loss-less switching for both main and
auxiliary switches without increasing the main switch current/voltage
rating. A winding coupled to the primary of power transformer
ensures ZCS for the auxiliary switches during their turn-off. A 350 W,
100 kHz phase shifted full bridge (PSFB) converter is built to validate
the analysis and design. Theoretical loss calculations for proposed
circuit is presented. The proposed circuit is compared with passive
soft switched PSFB in terms of efficiency and loss in duty cycle.
Abstract: This research study the application of the immobilized
TiO2 layer and Cu-TiO2 layer on graphite substrate as a negative
electrode or anode for Li-ion battery. The titania layer was produced
through chemical bath deposition method, meanwhile Cu particles
were deposited electrochemically. A material can be used as an
electrode as it has capability to intercalates Li ions into its crystal
structure. The Li intercalation into TiO2/Graphite and Cu-
TiO2/Graphite were analyzed from the changes of its XRD pattern
after it was used as electrode during discharging process. The XRD
patterns were refined by Le Bail method in order to determine the
crystal structure of the prepared materials. A specific capacity and the
cycle ability measurement were carried out to study the performance
of the prepared materials as negative electrode of the Li-ion battery.
The specific capacity was measured during discharging process from
fully charged until the cut off voltage. A 300 was used as a load.
The result shows that the specific capacity of Li-ion battery with
TiO2/Graphite as negative electrode is 230.87 ± 1.70mAh.g-1 which is
higher than the specific capacity of Li-ion battery with pure graphite
as negative electrode, i.e 140.75 ±0.46mAh.g-1. Meanwhile
deposition of Cu onto TiO2 layer does not increase the specific
capacity, and the value even lower than the battery with
TiO2/Graphite as electrode. The cycle ability of the prepared battery
is only two cycles, due to the Li ribbon which was used as cathode
became fragile and easily broken.
Abstract: The deficit of power for electricity demand reaches
almost 30% for consumers in the last few years. This reflects with
continually increasing the price of electricity, and today the price for
small industry is almost 110Euro/MWh. The high price is additional
problem for the owners in the economy crisis which is reflected with
higher price of the goods.
The paper gives analyses of the energy needs for real agro
complex in Macedonia, private vinery with capacity of over 2 million
liters in a year and with self grapes and fruits fields. The existing
power supply is from grid with 10/04 kV transformer. The
geographical and meteorological condition of the vinery location
gives opportunity for including renewable as a power supply option
for the vinery complex.
After observation of the monthly energy needs for the vinery, the
base scenario is the existing power supply from the distribution grid.
The electricity bill in small industry has three factors: electricity in
high and low tariffs in kWh and the power engaged for the
technological process of production in kW. These three factors make
the total electricity bill and it is over 110 Euro/MWh which is the
price near competitive for renewable option. On the other side
investments in renewable (especially photovoltaic (PV)) has tendency
of decreasing with price of near 1,5 Euro/W. This means that
renewable with PV can be real option for power supply for small
industry capacities (under 500kW installed power).
Therefore, the other scenarios give the option with PV and the last
one includes wind option. The paper presents some scenarios for
power supply of the vinery as the followings:
• Base scenario of existing conventional power supply from the
grid
• Scenario with implementation of renewable of Photovoltaic
• Scenario with implementation of renewable of Photovoltaic and
Wind power
The total power installed in a vinery is near 570 kW, but the
maximum needs are around 250kW. At the end of the full paper some
of the results from scenarios will be presented. The paper also
includes the environmental impacts of the renewable scenarios, as
well as financial needs for investments and revenues from renewable.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: Although water only takes a little percentage in the total mass of soil, it indeed plays an important role to the strength of structure. Moisture transfer can be carried out by many different mechanisms which may involve heat and mass transfer, thermodynamic phase change, and the interplay of various forces such as viscous, buoyancy, and capillary forces. The continuum models are not well suited for describing those phenomena in which the connectivity of the pore space or the fracture network, or that of a fluid phase, plays a major role. However, Lattice Boltzmann methods (LBMs) are especially well suited to simulate flows around complex geometries. Lattice Boltzmann methods were initially invented for solving fluid flows. Recently, fluid with multicomponent and phase change is also included in the equations. By comparing the numerical result with experimental result, the Lattice Boltzmann methods with phase change will be optimized.
Abstract: In this paper, an ultra low power and low jitter 12bit
CMOS digitally controlled oscillator (DCO) design is presented.
Based on a ring oscillator implemented with low power Schmitt
trigger based inverters. Simulation of the proposed DCO using 32nm
CMOS Predictive Transistor Model (PTM) achieves controllable
frequency range of 550MHz~830MHz with a wide linearity and high
resolution. Monte Carlo simulation demonstrates that the time-period
jitter due to random power supply fluctuation is under 31ps and the
power consumption is 0.5677mW at 750MHz with 1.2V power
supply and 0.53-ps resolution. The proposed DCO has a good
robustness to voltage and temperature variations and better linearity
comparing to the conventional design.
Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: This paper presents the results of an experimental study on the performance of a triboelectric separator of plastic mixtures used for recycling. The separator consists of four cylindrical electrodes. The principle behind the separation technique is based on the difference in the Coulomb force acting on the plastic particles after triboelectric charging. The separation of mixtures of acrylonitrile butadiene styrene (ABS) and polystyrene (PS) using this method was studied. The effects of the triboelectric charging time and applied voltage on the separation efficiency were investigated. The experimental results confirm that it is possible to obtain a high purity and recovery rate for the initial compositions considered in this study.
Abstract: There is need to explore emerging technologies based on carbon nanotube electronics as the MOS technology is approaching its limits. As MOS devices scale to the nano ranges, increased short channel effects and process variations considerably effect device and circuit designs. As a promising new transistor, the Carbon Nanotube Field Effect Transistor(CNTFET) avoids most of the fundamental limitations of the Traditional MOSFET devices. In this paper we present the analysis and comparision of a Carbon Nanotube FET(CNTFET) based 10(A current mirror with MOSFET for 32nm technology node. The comparision shows the superiority of the former in terms of 97% increase in output resistance,24% decrease in power dissipation and 40% decrease in minimum voltage required for constant saturation current. Furthermore the effect on performance of current mirror due to change in chirality vector of CNT has also been investigated. The circuit simulations are carried out using HSPICE model.
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: In a wind power generator using doubly fed induction
generator (DFIG), the three-phase pulse width modulation (PWM)
voltage source converter (VSC) is used as grid side converter (GSC)
and rotor side converter (RSC). The standard linear control laws
proposed for GSC provides not only instablity against comparatively
large-signal disturbances, but also the problem of stability due to
uncertainty of load and variations in parameters. In this paper, a
nonlinear controller is designed for grid side converter (GSC) of a
DFIG for wind power application. The nonlinear controller is
designed based on the input-output feedback linearization control
method. The resulting closed-loop system ensures a sufficient
stability region, make robust to variations in circuit parameters and
also exhibits good transient response. Computer simulations and
experimental results are presented to confirm the effectiveness of the
proposed control strategy.
Abstract: For gamma radiation detection, assemblies having
scintillation crystals and a photomultiplier tube, also there is a
preamplifier connected to the detector because the signals from
photomultiplier tube are of small amplitude. After pre-amplification
the signals are sent to the amplifier and then to the multichannel
analyser. The multichannel analyser sorts all incoming electrical
signals according to their amplitudes and sorts the detected photons
in channels covering small energy intervals. The energy range of
each channel depends on the gain settings of the multichannel
analyser and the high voltage across the photomultiplier tube. The
exit spectrum data of the two main isotopes studied ,putting data in
biomass program ,process it by Matlab program to get the solid
holdup image (solid spherical nuclear fuel)
Abstract: The hydrodynamic and thermal lattice Boltzmann
methods are applied to investigate the turbulent convective heat
transfer in the wavy channel flows. In this study, the turbulent
phenomena are modeling by large-eddy simulations with the
Smagorinsky model. As a benchmark, the laminar and turbulent
backward-facing step flows are simulated first. The results give good
agreement with other numerical and experimental data. For wavy
channel flows, the distribution of Nusselt number and the skin-friction
coefficients are calculated to evaluate the heat transfer effect and the
drag force. It indicates that the vortices at the trough would affect the
magnitude of drag and weaken the heat convection effects on the wavy
surface. In turbulent cases, if the amplitude of the wavy boundary is
large enough, the secondary vortices would be generated at troughs
and contribute to the heat convection. Finally, the effects of different
Re on the turbulent transport phenomena are discussed.
Abstract: This paper proposes the study of a robust control of
the doubly fed induction generator (DFIG) used in a wind energy
production. The proposed control is based on the linear active
disturbance rejection control (ADRC) and it is applied to the control
currents rotor of the DFIG, the DC bus voltage and active and
reactive power exchanged between the DFIG and the network. The
system under study and the proposed control are simulated using
MATLAB/SIMULINK.