Abstract: The proper selection of the AC-side passive filter
interconnecting the voltage source converter to the power supply is
essential to obtain satisfactory performances of an active power filter
system. The use of the LCL-type filter has the advantage of
eliminating the high frequency switching harmonics in the current
injected into the power supply. This paper is mainly focused on
analyzing the influence of the interface filter parameters on the active
filtering performances. Some design aspects are pointed out. Thus,
the design of the AC interface filter starts from transfer functions by
imposing the filter performance which refers to the significant current
attenuation of the switching harmonics without affecting the
harmonics to be compensated. A Matlab/Simulink model of the entire
active filtering system including a concrete nonlinear load has been
developed to examine the system performances. It is shown that a
gamma LC filter could accomplish the attenuation requirement of the
current provided by converter. Moreover, the existence of an optimal
value of the grid-side inductance which minimizes the total harmonic
distortion factor of the power supply current is pointed out.
Nevertheless, a small converter-side inductance and a damping
resistance in series with the filter capacitance are absolutely needed
in order to keep the ripple and oscillations of the current at the
converter side within acceptable limits. The effect of change in the
LCL-filter parameters is evaluated. It is concluded that good active
filtering performances can be achieved with small values of the
capacitance and converter-side inductance.
Abstract: Nanomaterials have attracted considerable attention
during the last two decades, due to their unusual electrical, mechanical
and other physical properties as compared with their bulky
counterparts. The mechanical properties of nanostructured materials
show strong size dependency, which has been explained within the
framework of continuum mechanics by including the effects of surface
stress. The size-dependent deformations of two-dimensional
nanosized structures with surface effects are investigated in the paper
by the finite element method. Truss element is used to evaluate the
contribution of surface stress to the total potential energy and the
Gurtin and Murdoch surface stress model is implemented with
ANSYS through its user programmable features. The proposed
approach is used to investigate size-dependent stress concentration
around a nanosized circular hole and the size-dependent effective
moduli of nanoporous materials. Numerical results are compared with
available analytical results to validate the proposed modeling
approach.
Abstract: Paper presents knowledge about types of test in area
of materials properties of selected methods of rapid prototyping
technologies. In today used rapid prototyping technologies for
production of models and final parts are used materials in initial state
as solid, liquid or powder material structure. In solid state are used
various forms such as pellets, wire or laminates. Basic range
materials include paper, nylon, wax, resins, metals and ceramics. In
Fused Deposition Modeling (FDM) rapid prototyping technology are
mainly used as basic materials ABS (Acrylonitrile Butadiene
Styrene), polyamide, polycarbonate, polyethylene and polypropylene.
For advanced FDM applications are used special materials as silicon
nitrate, PZT (Piezoceramic Material - Lead Zirconate Titanate),
aluminium oxide, hydroxypatite and stainless steel.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Nowadays, one of the most important problems of the
metropolises and the world large cities is the habitant traffic difficulty
and lack of sufficient parking site for the vehicles. Esfahan city as the
third metropolis of Iran has encountered with the vehicles parkingplace
problems in the most parts of fourteen regions of the city. The
non principled and non systematic dispersal and lack of parking sites
in the city has created an unfavorable status for its traffic and has
caused the air and sound pollutions increase; in addition, it wastes the
most portions of the citizenship and travelers' charge and time in
urban pathways and disturbs their mental and psychical calmness,
thus leads to their intensive dissatisfaction. In this study, by the usage
of AHP model in GIS environment, the effective criteria in selecting
the public parking sites have been combined with each other, and the
results of the created layers overlapping represent the parking
utilitarian vastness and widths. The achieved results of this research
indicate the pretty appropriate public parking sites selection in region
number 3 of Esfahan; but inconsequential dispersal and lack of these
parking sites in this region have caused abundant transportation
problems in Esfahan city.
Abstract: Nowadays, manufacturers are facing great challenges
with regard to the production of green products due to the emerging issue of hazardous substance management (HSM). In particular,
environmental legislation pressures have yielded to increased risk,
manufacturing complexity and green components demands. The green principles were expanded to many departments within
organization, including supply chain. Green supply chain
management (GSCM) was emerging in the last few years. This idea
covers every stage in manufacturing from the first to the last stage of
life cycle. From product lifecycle concept, the cycle starts at the design of a product. QFD is a customer-driven product development
tool, considered as a structured management approach for efficiently
translating customer needs into design requirements and parts deployment, as well as manufacturing plans and controls in order to
achieve higher customer satisfaction. This paper develops an Eco-
QFD to provide a framework for designing Eco-mobile phone by integrating the life cycle analysis LCA into QFD throughout the entire product development process.
Abstract: While in practice negotiation is always a mix of
cooperation and competition, these two elements correspond to
different approaches of the relationship and also different orientations
in term of strategy, techniques, tactics and arguments employed by
the negotiators with related effects and in the end leading to different
outcomes. The levels of honesty, trust and therefore cooperation are
influenced not only by the uncertainty of the situation, the objectives,
stakes or power but also by the orientation given from the very
beginning of the relationship. When negotiation is reduced to a
confrontation of power, participants rely on coercive measures, using
different kinds of threats or make false promises and bluff in order to
establish a more acceptable balance of power.
Most of the negotiators have a tendency to complain about the
unethical aspects of the tactics used by their counterparts while, as
the same time, they are mostly unaware of the sources of influence of
their own vision and practices. In this article, our intention is to
clarify these sources and try to understand what can lead negotiators
to unethical practices.
Abstract: Needs of an efficient information retrieval in recent
years in increased more then ever because of the frequent use of
digital information in our life. We see a lot of work in the area of
textual information but in multimedia information, we cannot find
much progress. In text based information, new technology of data
mining and data marts are now in working that were started from the
basic concept of database some where in 1960.
In image search and especially in image identification,
computerized system at very initial stages. Even in the area of image
search we cannot see much progress as in the case of text based
search techniques. One main reason for this is the wide spread roots
of image search where many area like artificial intelligence,
statistics, image processing, pattern recognition play their role. Even
human psychology and perception and cultural diversity also have
their share for the design of a good and efficient image recognition
and retrieval system.
A new object based search technique is presented in this paper
where object in the image are identified on the basis of their
geometrical shapes and other features like color and texture where
object-co-relation augments this search process.
To be more focused on objects identification, simple images are
selected for the work to reduce the role of segmentation in overall
process however same technique can also be applied for other
images.
Abstract: Incremental forming is a complex forming process with
continuously local cumulative deformation taking place during its
process, and springback that forming quality affected by would occur.
The springback evaluation method based on forming error
compensation also was proposed, which it can be defined as the
difference between theory and the actual amount of compensation
along the measured direction. According to forming error
compensation evaluation method, experiments was designed and
implemented. And from the results that obtained it can be show, the
magnitude of springback average (δE) of formed parts was very small,
and the forming precision could be significantly improved by adopting
compensation method. Based on double tensile stress state in the main
deformation area, a hypothesis that there is little springback be arisen
by bending behavior on the formed parts that was proposed.
Abstract: The leisure boatbuilding industry has tight profit margins that demand that boats are created to a high quality but with low cost. This requirement means reduced design times combined with increased use of design for production can lead to large benefits. The evolutionary nature of the boatbuilding industry can lead to a large usage of previous vessels in new designs. With the increase in automated tools for concurrent engineering within structural design it is important that these tools can reuse this information while subsequently feeding this to designers. The ability to accurately gather this materials and parts data is also a key component to these tools. This paper therefore aims to develop an architecture made up of neural networks and databases to feed information effectively to the designers based on previous design experience.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: The product development process (PDP) in the
Technology group plays a very important role in the launch of any
product. While a manufacturing process encourages the use of certain
measures to reduce health, safety and environmental (HSE) risks on
the shop floor, the PDP concentrates on the use of Geometric
Dimensioning and Tolerancing (GD&T) to develop a flawless design.
Furthermore, PDP distributes and coordinates activities between
different departments such as marketing, purchasing, and
manufacturing. However, it is seldom realized that PDP makes a
significant contribution to developing a product that reduces HSE
risks by encouraging the Technology group to use effective GD&T.
The GD&T is a precise communication tool that uses a set of
symbols, rules, and definitions to mathematically define parts to be
manufactured. It is a quality assurance method widely used in the oil
and gas sector. Traditionally it is used to ensure the
interchangeability of a part without affecting its form, fit, and
function. Parts that do not meet these requirements are rejected
during quality audits.
This paper discusses how the Technology group integrates this
quality assurance tool into the PDP and how the tool plays a major
role in helping the HSE department in its goal towards eliminating
HSE incidents. The PDP involves a thorough risk assessment and
establishes a method to address those risks during the design stage.
An illustration shows how GD&T helped reduce safety risks by
ergonomically improving assembling operations. A brief discussion
explains how tolerances provided on a part help prevent finger injury.
This tool has equipped Technology to produce fixtures, which are
used daily in operations as well as manufacturing. By applying
GD&T to create good fits, HSE risks are mitigated for operating
personnel. Both customers and service providers benefit from
reduced safety risks.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: Automatic methods of detecting changes through
satellite imaging are the object of growing interest, especially
beca²use of numerous applications linked to analysis of the Earth’s
surface or the environment (monitoring vegetation, updating maps,
risk management, etc...). This work implemented spatial analysis
techniques by using images with different spatial and spectral
resolutions on different dates. The work was based on the principle
of control charts in order to set the upper and lower limits beyond
which a change would be noted. Later, the a contrario approach was
used. This was done by testing different thresholds for which the
difference calculated between two pixels was significant. Finally,
labeled images were considered, giving a particularly low difference
which meant that the number of “false changes” could be estimated
according to a given limit.
Abstract: Clustering large populations is an important problem
when the data contain noise and different shapes. A good clustering
algorithm or approach should be efficient enough to detect clusters
sensitively. Besides space complexity, time complexity also gains
importance as the size grows. Using hierarchies we developed a new
algorithm to split attributes according to the values they have and
choosing the dimension for splitting so as to divide the database
roughly into equal parts as much as possible. At each node we
calculate some certain descriptive statistical features of the data
which reside and by pruning we generate the natural clusters with a
complexity of O(n).
Abstract: With the proliferation of multi-channel retailing, developing a better understanding of the factors that affect customers- purchase behaviors within a multi-channel retail context has become an important topic for practitioners and academics. While many studies have investigated the various customer behaviors associated with brick-and-mortar retailing, online retailing, and brick-and-click retailing, little research has explored how customer shopping value perceptions influence online purchase behaviors within the TV-and-online retail environment. The main purpose of this study is to investigate the influence of TV and online shopping values on online patronage intention. Data collected from 116 respondents in Taiwan are tested against the research model using the partial least squares (PLS) approach. The results indicate that utilitarian and hedonic TV shopping values have indirect, positive influences on online patronage intention through their online counterparts in the TV-and-online retail context. The findings of this study provide several important theoretical and practical implications for multi-channel retailing.
Abstract: Bones are dynamic and responsive organs, they
regulate their strength and mass according to the loads which they are subjected. Because, the Wnt/β-catenin pathway has profound
effects on the regulation of bone mass, we hypothesized that mechanical loading of bone cells stimulates Wnt/β-catenin signaling, which results in the generation of new bone mass.
Mechanical loading triggers the secretion of the Wnt molecule, which after binding to transmembrane proteins, causes GSK-3β (Glycogen synthase kinase 3 beta) to cease the phosphorylation of β-catenin. β-catenin accumulation in the cytoplasm, followed by its
transport into the nucleus, binding to transcription factors (TCF/LEF)
that initiate transcription of genes related to bone formation. To test this hypothesis, we used TOPGAL (Tcf Optimal Promoter
β-galactosidase) mice in an experiment in which cyclic loads were
applied to the forearm. TOPGAL mice are reporters for cells effected
by the Wnt/β-catenin signaling pathway. TOPGAL mice are genetically engineered mice in which transcriptional activation of β-
catenin, results in the production of an enzyme, β-galactosidase. The
presence of this enzyme allows us to localize transcriptional
activation of β-catenin to individual cells, thereby, allowing us to quantify the effects that mechanical loading has on the Wnt/β-catenin pathway and new bone formation. The ulnae of loaded TOPGAL
mice were excised and transverse slices along different parts of the
ulnar shaft were assayed for the presence of β-galactosidase.
Our results indicate that loading increases β-catenin transcriptional
activity in regions where this pathway is already primed (i.e. where basal activity is already higher) in a load magnitude dependent
manner. Further experiments are needed to determine the temporal and spatial activation of this signaling in relation to bone formation.
Abstract: Retrieval image by shape similarity, given a template
shape is particularly challenging, owning to the difficulty to derive a
similarity measurement that closely conforms to the common
perception of similarity by humans. In this paper, a new method for the
representation and comparison of shapes is present which is based on
the shape matrix and snake model. It is scaling, rotation, translation
invariant. And it can retrieve the shape images with some missing or
occluded parts. In the method, the deformation spent by the template
to match the shape images and the matching degree is used to evaluate
the similarity between them.
Abstract: This work consists of three parts. First, the alias-free
condition for the conventional two-channel quadrature mirror filter
bank is analyzed using complex arithmetic. Second, the approach
developed in the first part is applied to the complex quadrature mirror
filter bank. Accordingly, the structure is simplified and the theory is
easier to follow. Finally, a new class of complex quadrature mirror
filter banks is proposed. Interesting properties of this new structure
are also discussed.
Abstract: This paper presents modeling and optimization of two NP-hard problems in flexible manufacturing system (FMS), part type selection problem and loading problem. Due to the complexity and extent of the problems, the paper was split into two parts. The first part of the papers has discussed the modeling of the problems and showed how the real coded genetic algorithms (RCGA) can be applied to solve the problems. This second part discusses the effectiveness of the RCGA which uses an array of real numbers as chromosome representation. The novel proposed chromosome representation produces only feasible solutions which minimize a computational time needed by GA to push its population toward feasible search space or repair infeasible chromosomes. The proposed RCGA improves the FMS performance by considering two objectives, maximizing system throughput and maintaining the balance of the system (minimizing system unbalance). The resulted objective values are compared to the optimum values produced by branch-and-bound method. The experiments show that the proposed RCGA could reach near optimum solutions in a reasonable amount of time.